Ax3 weak wifi signal/range and wifi6

rafal17 · January 24, 2024, 8:56pm

Hi,
so far I have Hap Ac2 without external antennas
now I bought Hap Ax3 with two external antennas and unfortunately this new router has a worse wifi range, both 2Ghz and 5Ghz.
The old router had networks in N and of course I configured AX networks (wifi6) on the new one.
and unfortunately the wifi range is much smaller and does not cover the entire house.
Ac2 easily covered the entire house and some of the yard.
When I change the channel to the N network on Ax3, the range improves, but it is still slightly higher than Ac2.

Tested on 7.13.2 and 7.14beta8 programming.

Is this a problem with the router or antennas? Does band Ax have a shorter range than the older band N?

Possibly what else to configure on Ax3 to improve the WiFi range.

Here is my wifi configuration:

/interface wifi channel
add band=2ghz-ax disabled=no name=ch-2ghz skip-dfs-channels=10min-cac width=
20/40mhz
add band=5ghz-ax disabled=no name=ch-5ghz skip-dfs-channels=10min-cac width=
20/40mhz

/interface wifi configuration
add disabled=no mode=ap name=cfg_5G
security.authentication-types=“” ssid=TEST5
add disabled=no mode=ap name=cfg_2G
security.authentication-types=“” ssid=TEST2
add disabled=no mode=ap name=cfg_2G_goscie
security.authentication-types=“” ssid=TEST33

/interface wifi security
name=“profileSIEC1” authentication-types=wpa2-psk,wpa3-psk encryption=“” group-key-update=5m
passphrase=“XXXXXXXXXXX” management-protection=allowed
name=“profileSIEC2” authentication-types=wpa2-psk,wpa3-psk encryption=“” group-key-update=5m
passphrase=“XXXXXXXXXXX” management-protection=allowed
name=“profileSIEC3” authentication-types=wpa2-psk,wpa3-psk encryption=“” group-key-update=5m
passphrase=“XXXXXXXXXXX” management-protection=allowed

/interface wifi
set [ find default-name=wifi2 ] arp-timeout=5m channel=ch-2ghz configuration=
cfg_2G configuration.mode=ap disabled=no name=wlan1_2G security=
profileSIEC1 security.authentication-types=wpa2-psk,wpa3-psk .wps=disable
set [ find default-name=wifi1 ] arp-timeout=5m channel=ch-5ghz configuration=
cfg_5G configuration.mode=ap disabled=no name=wlan2_5G security=
profileSIEC2 security.authentication-types=wpa2-psk,wpa3-psk .wps=disable
add arp-timeout=5m configuration=cfg_2G_goscie configuration.hide-ssid=no
.mode=ap disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=
wlan1_2G name=wlan3_2G_goscie security=profileSIEC3
security.authentication-types=wpa2-psk,wpa3-psk .wps=disable

pterhu · January 25, 2024, 9:01am

Check this topic:
http://forum.mikrotik.com/t/hap-ax3-wireless-problem/172468/1

kalamaja · January 25, 2024, 9:17am

Check that bridge protocol-mode=rtsp
Check info about your country’s regulations: /interface/wifiwave2/radio/reg-info country=“Yourcountry” number=0
Set 5GHz frequency to 5500 and check if signal got better

rafal17 · January 25, 2024, 3:08pm

ad 1) I had and still have it established

ad 2)
/interface/wifiwave2/radio/reg-info country=“Poland” number=0
ranges: 2402-2482/20
5170-5250/23/indoor
5250-5330/23/indoor/dfs
5490-5730/30/dfs
5735-5875/14

ad 3) I set it and I don’t see much improvement
it may be that the 5Ghz network has improved a bit, but the 2Ghz network is still much weaker than on the old Ac2, both routers are placed next to each other

rafal17 · January 28, 2024, 7:35am

Hi,
should I understand that it is impossible to solve the problem with wifi coverage on hap Ax3?

marine88 · November 22, 2025, 8:04pm

Still have problem with my xiaomi box and my xiaomi tablet and mikrotik wifi 6 any idea ?

mikhailov · November 23, 2025, 3:11pm

Wireless performance is subject to hardware problems, software misconfiguration, noisy neighbors and constantly saturated radio frequency channels impacting one another. Higher frequency 5GHz has lower penetration than 2.4GHz but higher frequencis are generally less crowded. Do you want stable signal with no drops or unstable signal that is frequently disconnected? Or do you want stable and performant? How do you measure that change you made helped? How do you detect when a neighbor filled up radio frequency that was previously unused?

Mikrotik is high spec hardware with very low spec antennas. These cheap antennas make flagship wireless access points perform so bad that people give up. But investing in good antennas can solve problem better you can expect. At least it did for me. I almost gave up but talking to Mikrotik support, Antennas manufacture support and browsing the forum I found out what to do. An antenna can be high quality or low quality. An antenna placement can be good or can be very bad.

Before taking any advice on tuning wireless performance via software make sure you invest in 1) monitoring, 2) decent antenna, 3) thermal upgrade. No software tweaks can help to overcome inferior built-in antenna. It’s too suboptimal to work well no matter how you configure the driver. If you decide not to upgrade antenna, make sure it’s fully attached to the socket, as plug is flimsy.

Before 7.19.2 (when wireless driver was finally fixed) I was able to get stable wireless signal. I described all steps that helped to achieve good wireless performance on my AX^3 in every detail hAP AX^3 wireless performance journey . Based on my monitoring system results the version 7.19.4 is the best so far, still waiting to upgrade to 7.20.

jaclaz · November 23, 2025, 3:25pm

To be fair, in your (BTW very nice ) report, details on how exactly you enhanced cooling are completley missing, there is only a vague reference to:

... reduce number of thermal pads and paste, then CPU temperature went up to +72C under bandwidth load, I was very happy to see and continued working on thermal upgrade until it reached steady temperature without load and gradually increasing temperature under bandwidth test load ...

mikhailov · November 23, 2025, 3:40pm

This was lengthy 3-days process of trial and error. The goal was to make sure thermal throttling isn’t a problem.

I went through disassembling, replacing thermal pads and paste, measuring thermal under load every time. Factory thermal setup wasn’t good enough, thermal pads covered only a portion of a surface.

jaclaz · November 23, 2025, 3:52pm

So, essentially, you put larger thermal pads to completely cover the heating surfaces, thus increasing the transmission of heat to the dissipator(s)?

mikhailov · November 23, 2025, 4:22pm

yes, exactly, to make sure there isn’t overheating that may cause throttling under heavy benchmark load but higher spec antennas is what I needed the most to solve the problem with radio signal transmission

jaclaz · November 23, 2025, 4:45pm

Yep, the antenna change part is clear.

Cannot say if there is such an advantage using a single antenna with 2x2 conneciton over two separate antennas or even using the Mikrotik antennas with an extension cable to place them outside the rack.
It is very difficult to find comparison of different antennas and their real world capabilities.

Which thickness are the thermal pad you used?

mikhailov · November 23, 2025, 5:20pm

Using stock antennas with an extension cable could be an option but only for placement, not for signal strength. To be honest an antenna with cables weren’t much expensive than cable extension, so choice wasn’t too difficult to make.

Thermal pads I used were Gelid Solutions GP-Ultimate - Thermal Pad 90x50x1.0mm (2pcs). It doesn’t matter the brand as long as you can stack few pieces one to another in some areas, so an excessive heat can dissipate rather than accumulate in one place.

marine88 · November 23, 2025, 11:12pm

I tried everything I know and still have problem im using 2 wap ax and 1 cap ax2 and have disconnection from my xiaomi box 2nd gen. Even disabling the ft still have problems i trie version 7.19 7.20 7.21 beta and all of them my samsung galaxy s23 ultra and xiaomi box random disconnect from network logs show nothing im desperated. Everyone told me to buy ubiquiti but i was dumb and bought mikrotik because my main router was mikrotik. Here is my config

/interface wifi channel add band=2ghz-ax comment="CHANNELS 2.4 AX" disabled=no frequency=2412,2437,2462 name=ch-2-ax reselect-interval=23h..1d width=20mhz/interface wifi channel add band=5ghz-ax comment="CHANNELS 5 AX" deprioritize-unii-3-4=no disabled=no frequency=5180,5200,5220,5240,5745,5765,5785,5805,5825 name=ch-5-ax reselect-interval=23h..1d skip-dfs-channels=10min-cac width=20/40/80mhz/interface wifi channel add band=2ghz-n comment="CHANNELS 2.4 N" disabled=no frequency=2412,2437,2462 name=ch-2-n reselect-interval=23h..1d width=20mhz/interface wifi channel add band=5ghz-ac comment="CHANNELS 5 AC" disabled=no frequency=5180,5200,5220,5240,5745,5765,5785,5805,5825 name=ch-5-ac reselect-interval=23h..1d skip-dfs-channels=10min-cac width=20/40mhz/interface wifi security add authentication-types=wpa2-psk,wpa3-psk comment=GUEST connect-group="" connect-priority=0/1 disabled=no encryption=ccmp ft=yes ft-over-ds=yes name=sec-guest/interface wifi security add authentication-types=wpa-psk,wpa2-psk comment=DOMOTIC disabled=no management-protection=allowed name=sec-domotic wps=disable/interface wifi security add authentication-types=wpa2-psk,wpa3-psk comment=MAIN disabled=no encryption=ccmp ft=yes ft-over-ds=yes management-protection=allowed name=sec-main/interface wifi security add authentication-types=wpa-psk,wpa2-psk comment=CAMERAS disabled=no management-protection=allowed name=sec-cameras wps=disable/interface wifi steering add 2g-probe-delay=yes disabled=no name=steering-default rrm=yes wnm=yes/interface wifi configuration add channel=ch-2-ax channel.frequency=2412,2437,2462 comment="MAIN 2 AX" country=Portugal disabled=no hw-protection-mode=rts-cts interworking.internet=no mode=ap name=cfg-main-2-ax security=sec-main ssid=r&D_house steering=steering-default tx-power=15/interface wifi configuration add channel=ch-5-ax channel.reselect-interval=23h..1d .skip-dfs-channels=10min-cac comment="MAIN 5 AX" country=Portugal disabled=no mode=ap name=cfg-main-5-ax security=sec-main ssid=r&D_house steering=steering-default tx-power=20/interface wifi configuration add channel=ch-5-ac channel.frequency=5180,5200,5220,5240,5745,5765,5785,5805,5825 comment="MAIN 5 AC" country=Portugal disabled=no hide-ssid=no mode=ap name=cfg-main-5-ac security=sec-main ssid=r&D_house station-roaming=no steering=steering-default tx-power=20

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-main-5-ax disabled=no name=AP1_Office radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-main-2-ax disabled=no name=AP1_Office2 radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-main-5-ax disabled=no name=AP2_Bed radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-main-2-ax disabled=no name=AP2_Bed2 radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-main-2-ax disabled=no name=AP3_Room radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add channel.band=5ghz-ax .frequency=5180,5200,5220,5240,5745,5765,5785,5805,5825 configuration=cfg-main-5-ax configuration.mode=ap disabled=no name=AP3_Room2 radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-main-5-ac disabled=no name=AP4_Kitchen radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi datapath add bridge=bridge-LAN client-isolation=yes comment=GUEST disabled=no name=data-guest vlan-id=10/interface wifi datapath add bridge=bridge-LAN client-isolation=no comment=CAMERAS disabled=no name=data-cameras vlan-id=30/interface wifi datapath add bridge=bridge-LAN client-isolation=no comment=DOMOTIC disabled=no name=data-domotic vlan-id=50/interface wifi datapath add bridge=bridge-LAN client-isolation=no comment=WIFIAC disabled=no name=data-wifi-ac

/interface wifi configuration add channel=ch-2-ax comment="CAMERAS AX" datapath=data-cameras disabled=no hide-ssid=yes name=cfg-cameras-2-ax security=sec-cameras ssid=rD_cameras/interface wifi configuration add channel=ch-2-ax comment="DOMOTIC  AX" datapath=data-domotic disabled=no hide-ssid=yes mode=ap name=cfg-domotic-2-ax security=sec-domotic security.ft=no .ft-over-ds=no .ft-preserve-vlanid=no ssid=rD_domotic/interface wifi configuration add channel=ch-2-ax comment="GUEST 2 AX" datapath=data-guest disabled=no name=cfg-guest-2-ax security=sec-guest ssid=r&D_house_guest steering=steering-default/interface wifi configuration add channel=ch-5-ax comment="GUEST 5 AX" datapath=data-guest disabled=no name=cfg-guest-5-ax security=sec-guest ssid=r&D_house_guest station-roaming=yes steering=steering-default/interface wifi configuration add channel=ch-2-n comment="DOMOTIC N" country=Portugal datapath=data-wifi-ac disabled=no hide-ssid=yes mode=ap name=cfg-domotic-2-ac security=sec-domotic security-ft=no ssid=rD_domotic tx-power=18/interface wifi configuration add channel=ch-2-n comment="CAMERAS N" datapath=data-wifi-ac disabled=no hide-ssid=yes mode=ap name=cfg-cameras-ac security=sec-cameras ssid=rD_cameras/interface wifi configuration add channel=ch-5-ac comment="GUEST 5 AC" datapath=data-wifi-ac disabled=no hide-ssid=no name=cfg-guest-5-ac security=sec-guest ssid=r&D_house_guest steering=steering-default

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-guest-5-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP1_Office name=AP1_Office-virtual

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-guest-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP1_Office2 name=AP1_Office-virtual2

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-domotic-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP1_Office2 name=AP1_Office-virtual3

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-cameras-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP1_Office2 name=AP1_Office-virtual4

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-guest-5-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP2_Bed name=AP2_Bed-virtual

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-guest-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP2_Bed2 name=AP2_Bed-virtual2

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-domotic-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP2_Bed2 name=AP2_Bed-virtual3

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-cameras-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP2_Bed2 name=AP2_Bed-virtual4

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-guest-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP3_Room name=AP3_Room-virtual

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-domotic-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP3_Room name=AP3_Room-virtual2

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-cameras-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP3_Room name=AP3_Room-virtual3

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-guest-5-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP3_Room2 name=AP3_Room-virtual4

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-guest-5-ac disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP4_Kitchen name=AP4_Kitchen-virtual

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-domotic-2-ac disabled=no name=AP4_Kitchen2 radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi

operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP

add configuration=cfg-cameras-ac disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP4_Kitchen2 name=AP4_Kitchen-virtual2

/interface wifi access-list add action=accept comment="Aceitar sinal bom" disabled=no signal-range=-75..120/interface wifi access-list add action=accept allow-signal-out-of-range=2m comment="Aceitar sinal aceitavel" disabled=yes signal-range=-82..-76/interface wifi access-list add action=reject comment="Rejeitar sinal fraco" disabled=yes signal-range=-120..-83

/interface wifi cap set slaves-static=no/interface wifi capsman set ca-certificate=auto certificate=auto enabled=yes interfaces=bridge-LAN package-path=/firmware require-peer-certificate=no upgrade-policy=suggest-same-version

/interface wifi provisioning add action=create-enabled comment="WIFI AX 2.4" disabled=no master-configuration=cfg-main-2-ax name-format=%I slave-configurations=cfg-guest-2-ax,cfg-domotic-2-ax,cfg-cameras-2-ax slave-name-format=%I%v supported-bands=2ghz-ax/interface wifi provisioning add action=create-enabled comment="WIFI  AC 2.4" disabled=no master-configuration=cfg-domotic-2-ac name-format=%I slave-configurations=cfg-cameras-ac slave-name-format=%I%v supported-bands=2ghz-n/interface wifi provisioning add action=create-enabled comment="WIFI AX 5" disabled=no identity-regexp="" master-configuration=cfg-main-5-ax name-format=%I slave-configurations=cfg-guest-5-ax slave-name-format=%I%v supported-bands=5ghz-ax/interface wifi provisioning add action=create-enabled comment="WIFI AC 5" disabled=no master-configuration=cfg-main-5-ac name-format=%I slave-configurations=cfg-guest-5-ac slave-name-format=%I%v supported-bands=5ghz-ac

/interface wifi security multi-passphrase add comment=Cameras disabled=no group=iot+cameras vlan-id=30/interface wifi security multi-passphrase add comment=DOMOTIC disabled=no group=iot+cameras vlan-id=50

mikhailov · November 24, 2025, 8:01am

I tried everything I know and still have problem im using 2 wap ax and 1 cap ax2 and have disconnection from my xiaomi box 2nd gen.

Have you tried to measure radio signal strength per each device that experiences it? Is it stable? Is it changing under the load? Is any component of the router overheating? Are both antennas positioned correctly? How do they position at the moment?

Even disabling the ft still have problems i trie version 7.19 7.20 7.21 beta and all of them my samsung galaxy s23 ultra and xiaomi box random disconnect from network logs show nothing im desperated.

If logs show nothing why do you make a conclusion the problem is with the access point? Does the problem persist if you find less crowded frequency in a given time? Does the problem occur only to few devices? What happen to the other devices? What radio frequency are they on? How many devices connect to the access point? Do they often jump from 2.4GHz to 5Ghz? Does your 5GHz interface have higher Tx Power than 2.4GHz to compensate for shorter length wave? Have you tried to bind specific frequency to impacted devices via Wifi - Access List - Interface so they don’t jump while radio signal change?

Everyone told me to buy ubiquiti but i was dumb and bought mikrotik because my main router was mikrotik.

Opinions are subjective. You don’t have to use Mikrotik access point if you don’t want to but if you do such problems are solvable, alternative vendors may have better stock antennas, antennas placement or better thermal setup. The first step to solving the problem is to collect the data from sensors: radio signal strength per device and temperature sensors.

Here is my config

Configuration is incomplete, also this format is unreadable, can you share it in a way so no horizontall scrolling needed to analyze it please?

marine88 · November 24, 2025, 12:23pm

Here you have the configuration complete of the wifi the temperature are good devices are near the ap so signal strengh are also good

/interface wifi channel add band=2ghz-ax comment="CHANNELS 2.4 AX" disabled=no frequency=2412,2437,2462 name=ch-2-ax reselect-interval=23h..1d width=20mhz
/interface wifi channel add band=5ghz-ax comment="CHANNELS 5 AX" deprioritize-unii-3-4=no disabled=no frequency=5180,5200,5220,5240,5745,5765,5785,5805,5825 name=ch-5-ax reselect-interval=23h..1d skip-dfs-channels=10min-cac width=20/40/80mhz
/interface wifi channel add band=2ghz-n comment="CHANNELS 2.4 N" disabled=no frequency=2412,2437,2462 name=ch-2-n reselect-interval=23h..1d width=20mhz
/interface wifi channel add band=5ghz-ac comment="CHANNELS 5 AC" disabled=no frequency=5180,5200,5220,5240,5745,5765,5785,5805,5825 name=ch-5-ac reselect-interval=23h..1d skip-dfs-channels=10min-cac width=20/40mhz
/interface wifi security add authentication-types=wpa2-psk,wpa3-psk comment=GUEST connect-group="" connect-priority=0/1 disabled=no encryption=ccmp ft=yes ft-over-ds=yes name=sec-guest
/interface wifi security add authentication-types=wpa-psk,wpa2-psk comment=DOMOTIC disabled=no management-protection=allowed name=sec-domotic wps=disable
/interface wifi security add authentication-types=wpa2-psk,wpa3-psk comment=MAIN disabled=no encryption=ccmp ft=yes ft-over-ds=yes management-protection=allowed name=sec-main
/interface wifi security add authentication-types=wpa-psk,wpa2-psk comment=CAMERAS disabled=no management-protection=allowed name=sec-cameras wps=disable
/interface wifi steering add 2g-probe-delay=yes disabled=no name=steering-default rrm=yes wnm=yes
/interface wifi configuration add channel=ch-2-ax channel.frequency=2412,2437,2462 comment="MAIN 2 AX" country=Portugal disabled=no hw-protection-mode=rts-cts interworking.internet=no mode=ap name=cfg-main-2-ax security=sec-main ssid=r&D_house steering=steering-default tx-power=15
/interface wifi configuration add channel=ch-5-ax channel.reselect-interval=23h..1d .skip-dfs-channels=10min-cac comment="MAIN 5 AX" country=Portugal disabled=no mode=ap name=cfg-main-5-ax security=sec-main ssid=r&D_house steering=steering-default tx-power=20
/interface wifi configuration add channel=ch-5-ac channel.frequency=5180,5200,5220,5240,5745,5765,5785,5805,5825 comment="MAIN 5 AC" country=Portugal disabled=no hide-ssid=no mode=ap name=cfg-main-5-ac security=sec-main ssid=r&D_house station-roaming=no steering=steering-default tx-power=20

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-main-5-ax disabled=no name=AP1_Office radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-main-2-ax disabled=no name=AP1_Office2 radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-main-5-ax disabled=no name=AP2_Bed radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-main-2-ax disabled=no name=AP2_Bed2 radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-main-2-ax disabled=no name=AP3_Room radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add channel.band=5ghz-ax .frequency=5180,5200,5220,5240,5745,5765,5785,5805,5825 configuration=cfg-main-5-ax configuration.mode=ap disabled=no name=AP3_Room2 radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-main-5-ac disabled=no name=AP4_Kitchen radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi datapath add bridge=bridge-LAN client-isolation=yes comment=GUEST disabled=no name=data-guest vlan-id=10
/interface wifi datapath add bridge=bridge-LAN client-isolation=no comment=CAMERAS disabled=no name=data-cameras vlan-id=30
/interface wifi datapath add bridge=bridge-LAN client-isolation=no comment=DOMOTIC disabled=no name=data-domotic vlan-id=50
/interface wifi datapath add bridge=bridge-LAN client-isolation=no comment=WIFIAC disabled=no name=data-wifi-ac

/interface wifi configuration add channel=ch-2-ax comment="CAMERAS AX" datapath=data-cameras disabled=no hide-ssid=yes name=cfg-cameras-2-ax security=sec-cameras ssid=rD_cameras
/interface wifi configuration add channel=ch-2-ax comment="DOMOTIC  AX" datapath=data-domotic disabled=no hide-ssid=yes mode=ap name=cfg-domotic-2-ax security=sec-domotic security.ft=no .ft-over-ds=no .ft-preserve-vlanid=no ssid=rD_domotic
/interface wifi configuration add channel=ch-2-ax comment="GUEST 2 AX" datapath=data-guest disabled=no name=cfg-guest-2-ax security=sec-guest ssid=r&D_house_guest steering=steering-default
/interface wifi configuration add channel=ch-5-ax comment="GUEST 5 AX" datapath=data-guest disabled=no name=cfg-guest-5-ax security=sec-guest ssid=r&D_house_guest station-roaming=yes steering=steering-default
/interface wifi configuration add channel=ch-2-n comment="DOMOTIC N" country=Portugal datapath=data-wifi-ac disabled=no hide-ssid=yes mode=ap name=cfg-domotic-2-ac security=sec-domotic security-ft=no ssid=rD_domotic tx-power=18
/interface wifi configuration add channel=ch-2-n comment="CAMERAS N" datapath=data-wifi-ac disabled=no hide-ssid=yes mode=ap name=cfg-cameras-ac security=sec-cameras ssid=rD_cameras
/interface wifi configuration add channel=ch-5-ac comment="GUEST 5 AC" datapath=data-wifi-ac disabled=no hide-ssid=no name=cfg-guest-5-ac security=sec-guest ssid=r&D_house_guest steering=steering-default

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-guest-5-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP1_Office name=AP1_Office-virtual

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-guest-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP1_Office2 name=AP1_Office-virtual2

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-domotic-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP1_Office2 name=AP1_Office-virtual3

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-cameras-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP1_Office2 name=AP1_Office-virtual4

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-guest-5-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP2_Bed name=AP2_Bed-virtual

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-guest-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP2_Bed2 name=AP2_Bed-virtual2

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-domotic-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP2_Bed2 name=AP2_Bed-virtual3

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-cameras-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP2_Bed2 name=AP2_Bed-virtual4

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-guest-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP3_Room name=AP3_Room-virtual

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-domotic-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP3_Room name=AP3_Room-virtual2

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-cameras-2-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP3_Room name=AP3_Room-virtual3

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-guest-5-ax disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP3_Room2 name=AP3_Room-virtual4

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-guest-5-ac disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP4_Kitchen name=AP4_Kitchen-virtual

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-domotic-2-ac disabled=no name=AP4_Kitchen2 radio-mac=XX:XX:XX:XX:XX:XX

/interface wifi
# operated by CAP XX:XX:XX:XX:XX:XX%bridge-LAN, traffic processing on CAP
add configuration=cfg-cameras-ac disabled=no mac-address=XX:XX:XX:XX:XX:XX master-interface=AP4_Kitchen2 name=AP4_Kitchen-virtual2

/interface wifi access-list add action=accept comment="Aceitar sinal bom" disabled=no signal-range=-75..120
/interface wifi access-list add action=accept allow-signal-out-of-range=2m comment="Aceitar sinal aceitavel" disabled=yes signal-range=-82..-76
/interface wifi access-list add action=reject comment="Rejeitar sinal fraco" disabled=yes signal-range=-120..-83

/interface wifi cap set slaves-static=no
/interface wifi capsman set ca-certificate=auto certificate=auto enabled=yes interfaces=bridge-LAN package-path=/firmware require-peer-certificate=no upgrade-policy=suggest-same-version

/interface wifi provisioning add action=create-enabled comment="WIFI AX 2.4" disabled=no master-configuration=cfg-main-2-ax name-format=%I slave-configurations=cfg-guest-2-ax,cfg-domotic-2-ax,cfg-cameras-2-ax slave-name-format=%I%v supported-bands=2ghz-ax
/interface wifi provisioning add action=create-enabled comment="WIFI  AC 2.4" disabled=no master-configuration=cfg-domotic-2-ac name-format=%I slave-configurations=cfg-cameras-ac slave-name-format=%I%v supported-bands=2ghz-n
/interface wifi provisioning add action=create-enabled comment="WIFI AX 5" disabled=no identity-regexp="" master-configuration=cfg-main-5-ax name-format=%I slave-configurations=cfg-guest-5-ax slave-name-format=%I%v supported-bands=5ghz-ax
/interface wifi provisioning add action=create-enabled comment="WIFI AC 5" disabled=no master-configuration=cfg-main-5-ac name-format=%I slave-configurations=cfg-guest-5-ac slave-name-format=%I%v supported-bands=5ghz-ac

/interface wifi security multi-passphrase add comment=Cameras disabled=no group=iot+cameras vlan-id=30
/interface wifi security multi-passphrase add comment=DOMOTIC disabled=no group=iot+cameras vlan-id=50

mikhailov · November 24, 2025, 4:31pm

You re looking for a quick misleading naive answer that won’t help, right? Sorry, it’s difficult to answer your question based on information you provide

marine88 · November 24, 2025, 7:41pm

I don´t understand why you say that? What information you need more?