Cant bridge IPX traffic (novell)

RouterOS Forwarding Protocols
1

Hi.
I have omnitik as a AP (ap bridge+wds). it seems to not forward IPX trafiic. Before it was two ovislink devices and everythink worked fine, now i changed one ovislink to omnitik and IPX doesnt work. I tried to sniff packets but it gives me nothing.
/system resource print
uptime: 3d7h29m42s
version: 5.26
free-memory: 49712KiB
total-memory: 62184KiB
cpu: MIPS 24Kc V7.4
cpu-count: 1
cpu-frequency: 400MHz
cpu-load: 6%
free-hdd-space: 90552KiB
total-hdd-space: 126976KiB
write-sect-since-reboot: 19679
write-sect-total: 20954
bad-blocks: 0.2%
architecture-name: mipsbe
board-name: RB OmniTIK U-5HnD
platform: MikroTik
Configuration:
interface wireless print
Flags: X - disabled, R - running
0 R name="wlan1" mtu=1500 mac-address=xx:xx:xx:xx:xx:xx arp=enabled interface-type=Atheros 11N mode=ap-bridge ssid="xxx" frequency=5180
band=5ghz-a channel-width=20mhz scan-list=default wireless-protocol=802.11 wds-mode=dynamic wds-default-bridge=bridge1 wds-ignore-ssid=no
bridge-mode=enabled default-authentication=no default-forwarding=no default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no
security-profile=default compression=no

/interface bridge print
Flags: X - disabled, R - running
0 R name="bridge1" mtu=1500 l2mtu=1600 arp=enabled mac-address=xx protocol-mode=none priority=0x8000 auto-mac=no
admin-mac=xx max-message-age=20s forward-delay=15s transmit-hold-count=6 ageing-time=5m

inter br por pri
Flags: X - disabled, I - inactive, D - dynamic

INTERFACE BRIDGE PRIORITY PATH-COST HORIZON

0 I ether2 bridge1 0x80 10 none
1 wlan1 bridge1 0x80 10 none
2 ether1 bridge1 0x80 10 none
3 I ether3 bridge1 0x80 10 none
4 I ether4 bridge1 0x80 10 none
5 I ether5 bridge1 0x80 10 none
6 D wds2 bridge1 0x80 74 none
7 D wds1

So as you see its pure bridge without any filters.

2

You set default-forwarding=no on wireless interface.
The default is yes on all version of RouterOS, is your fault.

3

As for IPX, NCP (which is the only common protocol that was used with IPX/SPX) had TCP/IP support added almost 20 years ago.

4

It has to be like that, i dont need it because i have wireless client added to access list.

Its not my network, it has to be on pure IPX.

5

default forwarding is not the same as default authenticate. Set default forwarding to yes and default authenticate to no for what you want to do.

6

I have plenty of mikrotik devices and i always have default forward to “no”.
From MT wiki:
“default-forwarding (yes | no; Default: yes) This is the value of forwarding for clients that do not match any entry in the access-list”
Its my default config so i know what im saying.

IT DOESNT HAVE ANYTING WITH MY PROBLEM.

7

“/export compact”

8

/certificate
add common-name=changeme country=US locality=SanFrancisco name=cert1
organization=Fort-Funston state=CA subject-alt-name=
email:mail@host.domain trusted=yes unit=changeme
add common-name=changeme country=US locality=SanFrancisco name=cert2
organization=Fort-Funston state=CA subject-alt-name=
email:mail@host.domain trusted=yes unit=changeme
/interface bridge
add admin-mac=xx auto-mac=no l2mtu=1598 name=bridge1
protocol-mode=none
/interface wireless
set [ find default-name=wlan1 ] default-authentication=no default-forwarding=
no disabled=no l2mtu=2290 mac-address=xx mode=ap-bridge
radio-name=xx ssid=chemikow wds-default-bridge=bridge1
wds-mode=dynamic wireless-protocol=802.11
/interface ethernet
set [ find default-name=ether1 ] comment=“UPLINK” mac-address=
xx
/ip neighbor discovery
set ether1 comment=“UPLINK”
/interface ethernet switch port
set 0 vlan-mode=disabled
set 1 vlan-mode=disabled
set 2 vlan-mode=disabled
set 3 vlan-mode=disabled
set 4 vlan-mode=disabled
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik wpa-pre-shared-key=
46A5043B431D wpa2-pre-shared-key=46A5043B431D
/ip hotspot user profile
set [ find default=yes ] idle-timeout=none keepalive-timeout=2m
mac-cookie-timeout=3d
/ip ipsec proposal
set [ find default=yes ] enc-algorithms=3des
/system logging action
set 0 memory-lines=100
set 1 disk-lines-per-file=100
/interface bridge filter
add action=log chain=forward log-prefix=test mac-protocol=ipx
/interface bridge port
add bridge=bridge1 edge=no external-fdb=no interface=ether2 point-to-point=no
add bridge=bridge1 edge=no external-fdb=no interface=wlan1 point-to-point=no
add bridge=bridge1 edge=no external-fdb=no interface=ether1 point-to-point=no
add bridge=bridge1 edge=no external-fdb=no interface=ether3 point-to-point=no
add bridge=bridge1 edge=no external-fdb=no interface=ether4 point-to-point=no
add bridge=bridge1 edge=no external-fdb=no interface=ether5 point-to-point=no
/interface bridge settings
set allow-fast-path=no
/interface wireless access-list
add comment=192.168.1.101 mac-address=xx (this is troubleshooting link)
add comment=192.168.1.102 mac-address=xx
/interface wireless connect-list
add comment=192.168.1.101 interface=wlan1 mac-address=xx
security-profile=default
add comment=192.168.1.102 interface=wlan1 mac-address=xx
security-profile=default
/ip address
add address=192.168.1.100/24 comment=“default configuration” interface=
bridge1 network=192.168.1.0
/ip dhcp-client
add comment=“default configuration” dhcp-options=hostname,clientid interface=
bridge1
/ip dns
set allow-remote-requests=yes
/ip dns static
add address=192.168.88.1 name=router
/ip firewall connection tracking
set enabled=no
/ip firewall service-port
set ftp disabled=yes
set tftp disabled=yes
set irc disabled=yes
set h323 disabled=yes
set sip disabled=yes
set pptp disabled=yes
/ip route
add distance=1 dst-address=172.28.255.0/24 gateway=192.168.185.1
/ip service
set ftp disabled=yes
set www disabled=yes
set www-ssl certificate=cert1 disabled=no port=8080
set api disabled=yes
/ip upnp
set allow-disable-external-interface=no
/system clock
set time-zone-name=Europe/Warsaw
/system identity
set name=XX
/system logging
set 0 action=disk
set 1 action=disk
set 3 action=disk
/system ntp client
set enabled=yes mode=unicast primary-ntp=xx

9

I do not see any trouble on that config… check the machine?