# CHR on OVH VPS SSD

**URL:** <https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670>\
**Category:** Virtualization\
**Created:** [April 5, 2017, 4:50am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670 "2017-04-05T04:50:48Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![th0massin0](https://forum.mikrotik.com/letter_avatar/th0massin0/32/6_449c533f586939b6e5f246632a46421f.png) [@th0massin0](https://forum.mikrotik.com/u/th0massin0)\
**Post date:** [April 5, 2017, 4:50am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/1 "2017-04-05T04:50:48Z")

</div>

1. RouterOS \>= 6.42rc52
2. Boot VPS to rescue mode from OVH panel.
3. Login via ssh.
4. Execute this TWO lines:

v7.6

```plaintext
cd /root && curl -O https://download.mikrotik.com/routeros/7.6/chr-7.6.img.zip && gunzip -S .zip chr-7.6.img.zip && umount /mnt/sdb1
dd if=/root/chr-7.6.img of=/dev/sdb

```

v6.48.6

```plaintext
cd /root && curl -O https://download.mikrotik.com/routeros/6.48.6/chr-6.48.6.img.zip && gunzip -S .zip chr-6.48.6.img.zip && umount /mnt/sdb1
dd if=/root/chr-6.48.6.img of=/dev/sdb

```

1. Reboot from OVH panel, done!

---

<div class="post-metadata">

**Author:** ![Chupaka](https://forum.mikrotik.com/user_avatar/forum.mikrotik.com/chupaka/32/215_2.png) [@Chupaka](https://forum.mikrotik.com/u/Chupaka)\
**Post date:** [April 14, 2017, 2:37pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/2 "2017-04-14T14:37:31Z")

</div>

Have you tried to dd already installed image from some other VM?

---

<div class="post-metadata">

**Author:** ![th0massin0](https://forum.mikrotik.com/letter_avatar/th0massin0/32/6_449c533f586939b6e5f246632a46421f.png) [@th0massin0](https://forum.mikrotik.com/u/th0massin0)\
**Post date:** [April 18, 2017, 6:41pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/3 "2017-04-18T18:41:14Z")

</div>

Thank you for your answer. Even if it would work, that configuration will be unsupported, so if something will goes wrong, nobody could help me with it.  
CHR is relatively young product that should be ‘polished’ in the matter of compatibility (in my opinion open vm tools and drivers). Today the general-use distros offers better compatibility with vm enviorment than specialized cloud mikrotik solution.

---

<div class="post-metadata">

**Author:** ![Chupaka](https://forum.mikrotik.com/user_avatar/forum.mikrotik.com/chupaka/32/215_2.png) [@Chupaka](https://forum.mikrotik.com/u/Chupaka)\
**Post date:** [April 18, 2017, 7:27pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/4 "2017-04-18T19:27:38Z")

</div>

Unsupported by whom? OVH won’t support any CHR installation, I think. MikroTik doesn’t care - it’s just like moving the disk to another machine. If it works - you’re just lucky.

---

<div class="post-metadata">

**Author:** ![roulyz](https://forum.mikrotik.com/user_avatar/forum.mikrotik.com/roulyz/32/1678_2.png) [@roulyz](https://forum.mikrotik.com/u/roulyz)\
**Post date:** [May 21, 2017, 10:52am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/5 "2017-05-21T10:52:48Z")

</div>

Just run this command.  
PS : check your interface name before apply. here the interface name is : “ens3”. Change according yours 😃

wget [https://download2.mikrotik.com/routeros/6.39.1/chr-6.39.1.img.zip](https://download2.mikrotik.com/routeros/6.39.1/chr-6.39.1.img.zip) -O chr.img.zip &&   
gunzip -c chr.img.zip \> chr.img &&   
mount -o loop,offset=33554944 chr.img /mnt &&   
ADDRESS=`ip addr show ens3 | grep global | cut -d' ' -f 6 | head -n 1` &&   
GATEWAY=`ip route list | grep default | cut -d' ' -f 3` &&   
echo "/ip address add address=$ADDRESS interface=[/interface ethernet find where name=ether1]  
/ip route add gateway=$GATEWAY  
" \> /mnt/rw/autorun.scr &&   
umount /mnt &&   
echo u \> /proc/sysrq-trigger &&   
dd if=chr.img bs=1024 of=/dev/vda

---

<div class="post-metadata">

**Author:** ![th0massin0](https://forum.mikrotik.com/letter_avatar/th0massin0/32/6_449c533f586939b6e5f246632a46421f.png) [@th0massin0](https://forum.mikrotik.com/u/th0massin0)\
**Post date:** [June 16, 2017, 9:40am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/6 "2017-06-16T09:40:50Z")

</div>

> [@roulyz](#):
>
> Just run this command.  
> PS : check your interface name before apply. here the interface name is : “ens3”. Change according yours 😃
> 
> wget [https://download2.mikrotik.com/routeros/6.39.1/chr-6.39.1.img.zip](https://download2.mikrotik.com/routeros/6.39.1/chr-6.39.1.img.zip) -O chr.img.zip &&   
> gunzip -c chr.img.zip \> chr.img &&   
> mount -o loop,offset=33554944 chr.img /mnt &&   
> ADDRESS=`ip addr show ens3 | grep global | cut -d' ' -f 6 | head -n 1` &&   
> GATEWAY=`ip route list | grep default | cut -d' ' -f 3` &&   
> echo "/ip address add address=$ADDRESS interface=[/interface ethernet find where name=ether1]  
> /ip route add gateway=$GATEWAY  
> " \> /mnt/rw/autorun.scr &&   
> umount /mnt &&   
> echo u \> /proc/sysrq-trigger &&   
> dd if=chr.img bs=1024 of=/dev/vda

Could you tell me what is the purpose of that manual? The problem is lack of (v)hard disk controller driver.

---

<div class="post-metadata">

**Author:** ![Chupaka](https://forum.mikrotik.com/user_avatar/forum.mikrotik.com/chupaka/32/215_2.png) [@Chupaka](https://forum.mikrotik.com/u/Chupaka)\
**Post date:** [June 16, 2017, 9:57am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/7 "2017-06-16T09:57:44Z")

</div>

So, it lacks the driver in whole RouterOS or only in CHR Image Installer?

---

<div class="post-metadata">

**Author:** ![savage](https://forum.mikrotik.com/user_avatar/forum.mikrotik.com/savage/32/56094_2.png) [@savage](https://forum.mikrotik.com/u/savage)\
**Post date:** [June 16, 2017, 7:46pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/8 "2017-06-16T19:46:21Z")

</div>

There has been some posts floating around on the forum about converting the IDE disk to SCSI, and making it work that way with a few more different type of setups.

search a bit, perhaps theyll work for you 🙂

---

<div class="post-metadata">

**Author:** ![drbunsen](https://forum.mikrotik.com/letter_avatar/drbunsen/32/6_449c533f586939b6e5f246632a46421f.png) [@drbunsen](https://forum.mikrotik.com/u/drbunsen)\
**Post date:** [October 19, 2017, 1:15pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/9 "2017-10-19T13:15:43Z")

</div>

Some time ago I’ve tried to install CHR on a Hetzner VPS, unfortunately I ran into exactly the same issue.  
It would be nice if Mikrotik could support virtio SCSI storage controllers as well.

---

<div class="post-metadata">

**Author:** ![Wencey](https://forum.mikrotik.com/letter_avatar/wencey/32/6_449c533f586939b6e5f246632a46421f.png) [@Wencey](https://forum.mikrotik.com/u/Wencey)\
**Post date:** [November 2, 2017, 4:56am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/10 "2017-11-02T04:56:36Z")

</div>

i use bandwagon and i meet the same issue.

---

<div class="post-metadata">

**Author:** ![raffav](https://forum.mikrotik.com/letter_avatar/raffav/32/6_449c533f586939b6e5f246632a46421f.png) [@raffav](https://forum.mikrotik.com/u/raffav)\
**Post date:** [January 31, 2018, 10:33pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/11 "2018-01-31T22:33:49Z")

</div>

> [@Muqatil](#):
>
> Hello  
> I am trying to install CHR on VPS OVH SSD from raw image (recovery mode and dd).
> 
> ```plaintext
> cd /root
> curl -O http://download2.mikrotik.com/routeros/6.38.5/chr-6.38.5.img.zip
> gunzip -S .zip chr-6.38.5.img.zip
> umount /mnt/sdb1
> dd if=/root/chr-6.38.5.img of=/dev/sdb
> 
> ```
> 
> After reboot RouterOS won’t boot. I attach screen from console. Aprox. one year ago OVH config was able to run CHR, today is not.  
> I am aware that some kind of VirtIO problems was fixed in 6.31, but please keep in mind, that I am trying to use 6.38.5.  
> Please help
> 
> PS: Info about SCSI controller from lspci:
> 
> ```plaintext
> 00:04.0 SCSI storage controller: Red Hat, Inc Virtio SCSI
> Subsystem: Red Hat, Inc Device 0008
> Physical Slot: 4
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at c000 [size=64]
> Region 1: Memory at febd2000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] MSI-X: Enable+ Count=4 Masked-
> Vector table: BAR=1 offset=00000000
> PBA: BAR=1 offset=00000800
> Kernel driver in use: virtio-pci
> Kernel modules: virtio_pci
> 
> ```
> 
> Simillar problem:  
> [http://forum.mikrotik.com/t/error-in-virtio-disk-driver-in-6-31/90727/1](http://forum.mikrotik.com/t/error-in-virtio-disk-driver-in-6-31/90727/1)  
> [http://forum.mikrotik.com/t/chr-fatal-error-no-harddrives-found/95490/1](http://forum.mikrotik.com/t/chr-fatal-error-no-harddrives-found/95490/1)  
>   
>   
> Update:  
> I’ve prabobly found main couse of the failure. Error occurs only when guest disk bus type is set to SCSI ().  
> Settings that works: VirtIO, IDE, SATA.  
>   
>   
> Update (2), news from Mikrotik support:
> 
> > RouterOS does not support SCSI disk installation(..)
> 
> Update (3), news from OVH Support:
> 
> > There are no possibility to change VPS config, nor buy VPS from older region.  
> >   
> >   
> > Dear Mikrotik Developers, could you please fix this?  
> > In case of OVH VPS SSD (and many more budget VPSes) it’s impossible to modify guest config details.  
> >   
> >   
> > Edit: another request, [http://forum.mikrotik.com/t/chr-suggestions-for-new-functionality/111599/120](http://forum.mikrotik.com/t/chr-suggestions-for-new-functionality/111599/120)

hi  
i think ramnode support ide driver  
look at attachments  
 ![Untitled.png](https://data-discourse.cdn.mikrotik.com/original/3X/2/a/2af66dfc3cacb3c53132d41a48c947b8f49dc21c.png)

---

<div class="post-metadata">

**Author:** ![th0massin0](https://forum.mikrotik.com/letter_avatar/th0massin0/32/6_449c533f586939b6e5f246632a46421f.png) [@th0massin0](https://forum.mikrotik.com/u/th0massin0)\
**Post date:** [January 31, 2018, 10:34pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/12 "2018-01-31T22:34:30Z")

</div>

Looks promissing. Thank you!

---

<div class="post-metadata">

**Author:** ![raffav](https://forum.mikrotik.com/letter_avatar/raffav/32/6_449c533f586939b6e5f246632a46421f.png) [@raffav](https://forum.mikrotik.com/u/raffav)\
**Post date:** [February 1, 2018, 2:14am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/13 "2018-02-01T02:14:39Z")

</div>

> [@th0massin0](#):
>
> Looks promissing. Thank you!

Hi,  
Do you know if is possible to try this on openvps instead of kvm?  
Because in ramnode there is a vpz small one that cost 15 dollars yearly, very cheap  
@th0massin0

> Edited

DIT

worked thanks allot  
 ![Untitled.png](https://data-discourse.cdn.mikrotik.com/original/3X/1/4/14a6feb020350fe8d6576560945da2cb947053be.png)  
Enviado de meu XT1580 usando Tapatalk

---

<div class="post-metadata">

**Author:** ![th0massin0](https://forum.mikrotik.com/letter_avatar/th0massin0/32/6_449c533f586939b6e5f246632a46421f.png) [@th0massin0](https://forum.mikrotik.com/u/th0massin0)\
**Post date:** [February 2, 2018, 11:25pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/14 "2018-02-02T23:25:30Z")

</div>

CHR can run only in full virtualization like vmware, kvm, xen or hyper-v

---

<div class="post-metadata">

**Author:** ![raffav](https://forum.mikrotik.com/letter_avatar/raffav/32/6_449c533f586939b6e5f246632a46421f.png) [@raffav](https://forum.mikrotik.com/u/raffav)\
**Post date:** [February 3, 2018, 11:06am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/15 "2018-02-03T11:06:20Z")

</div>

> [@th0massin0](#):
>
> CHR can run only in full virtualization like vmware, kvm, xen or hyper-v

Was a little pain in the ass to find a Linux on the ramnode repository that work smoth in 512mb and since I don’t have skills on Linux I need to do some research how formart a disk via command line,  
After some live cd crash, freezes i maked work  
  
  
  
Enviado de meu XT1580 usando Tapatalk

---

<div class="post-metadata">

**Author:** ![odvolk](https://forum.mikrotik.com/letter_avatar/odvolk/32/6_449c533f586939b6e5f246632a46421f.png) [@odvolk](https://forum.mikrotik.com/u/odvolk)\
**Post date:** [February 15, 2018, 11:29am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/16 "2018-02-15T11:29:13Z")

</div>

> [@](#):
>
> Was a little pain in the ass to find a Linux on the ramnode repository that work smoth in 512mb and since I don’t have skills on Linux I need to do some research how formart a disk via command line,  
> After some live cd crash, freezes i maked work

Hi! I wanted to know how could you manage with this? Can you bring some instructions on this? We bought an “VPS 2016 SSD 1” @ [OVH.com](http://OVH.com) and we are suffering some ass f\*\*\*k with their system. Please, help us

---

<div class="post-metadata">

**Author:** ![dadag90](https://forum.mikrotik.com/letter_avatar/dadag90/32/6_449c533f586939b6e5f246632a46421f.png) [@dadag90](https://forum.mikrotik.com/u/dadag90)\
**Post date:** [July 31, 2018, 5:15am UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/17 "2018-07-31T05:15:31Z")

</div>

> [@Muqatil](#):
>
> 1. RouterOS \>= 6.42rc52
> 2. Boot VPS to rescue mode from OVH panel.
> 3. Login via ssh.
> 4. Execute this TWO lines:
> 
> ```plaintext
> cd /root && curl -O https://download2.mikrotik.com/routeros/6.42.3/chr-6.42.3.img.zip && gunzip -S .zip chr-6.42.3.img.zip && umount /mnt/sdb1
> dd if=/root/chr-6.42.3.img of=/dev/sdb
> 
> ```
> 
> 1. Reboot from OVH panel, done!

I install CHR yesterday (30.07.2018). I must change sdb into vdb

```plaintext
cd /root && curl -O https://download2.mikrotik.com/routeros/6.42.3/chr-6.42.3.img.zip && gunzip -S .zip chr-6.42.3.img.zip && umount /mnt/vdb1
dd if=/root/chr-6.42.3.img of=/dev/vdb

```

---

<div class="post-metadata">

**Author:** ![inframe](https://forum.mikrotik.com/letter_avatar/inframe/32/6_449c533f586939b6e5f246632a46421f.png) [@inframe](https://forum.mikrotik.com/u/inframe)\
**Post date:** [August 8, 2018, 4:50pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/18 "2018-08-08T16:50:24Z")

</div>

how to update this CHR to the new version?

---

<div class="post-metadata">

**Author:** ![drbunsen](https://forum.mikrotik.com/letter_avatar/drbunsen/32/6_449c533f586939b6e5f246632a46421f.png) [@drbunsen](https://forum.mikrotik.com/u/drbunsen)\
**Post date:** [August 8, 2018, 6:15pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/19 "2018-08-08T18:15:57Z")

</div>

Update is as with any other Mikrotik device. Upload the image (x86 for CHR) and reboot.

---

<div class="post-metadata">

**Author:** ![inframe](https://forum.mikrotik.com/letter_avatar/inframe/32/6_449c533f586939b6e5f246632a46421f.png) [@inframe](https://forum.mikrotik.com/u/inframe)\
**Post date:** [August 8, 2018, 8:45pm UTC](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670/20 "2018-08-08T20:45:59Z")

</div>

> [@](#):
>
> Update is as with any other Mikrotik device. Upload the image (x86 for CHR) and reboot.

Thank you! Download image x86 and updated my CHR 😒

[Next page](https://forum.mikrotik.com/t/chr-on-ovh-vps-ssd/107670.md?page=2)
