# Configuring VLAN Trunking on MT Router to Cisco C2924 Switch

**URL:** <https://forum.mikrotik.com/t/configuring-vlan-trunking-on-mt-router-to-cisco-c2924-switch/21509>\
**Category:** General\
**Created:** [May 30, 2008, 2:43pm UTC](https://forum.mikrotik.com/t/configuring-vlan-trunking-on-mt-router-to-cisco-c2924-switch/21509 "2008-05-30T14:43:34Z")\
**Posts on this page:** 1\
**Showing post:** 1

<div class="post-metadata">

**Author:** ![rgraham](https://forum.mikrotik.com/user_avatar/forum.mikrotik.com/rgraham/32/101_2.png) [@rgraham](https://forum.mikrotik.com/u/rgraham)\
**Post date:** [May 30, 2008, 2:43pm UTC](https://forum.mikrotik.com/t/configuring-vlan-trunking-on-mt-router-to-cisco-c2924-switch/21509/1 "2008-05-30T14:43:34Z")

</div>

I saw that some others had difficulty with vlans as I did.  
I thought I’d share how I configured the MT router for VLAN trunking to a Cisco Switch.  
These steps worked for me. The statements were pulled from my router.  
I have a total of 4 vlans now but I show only two in this example.  
I hope this helps others that are trying to use Cisco switches with MT Routers.

Steps I used to configure VLAN trunking on a MT Router to a Cisco C2924 Switch  
1.) Configure a port on the switch for Trunking and connect that port to the MT Router  
2.) Configure the Vlan Database in the switch with all the vlans that will be used.  
3.) Add a bridge in the MT Router.  
4.) Add the Vlans to the bridge that would be used on the switch, except the native vlan.  
5.) Add the port going to the switch port that was configured for trunking to the bridge  
6.) Add an IP address to the bridge created above. It is used to communicate to the switch’s native vlan.  
7.) Add an IP address to the vlans. In this example VLAN2  
8.) Now set the ports on the switch to access the vlans you want them to communicate on.  
  
  
\

* * *

Example configuration of a MT Router to a Cisco C2924 Switch.  
The switch has VLAN1 and VLAN2 with VLAN1 being the native vlan on the  
switch. You would add additional vlans like VLAN2.

In this example VLAN 1 uses DHCP. Hosts on VLAN2 are servers with static addresses.  
  
  
/interface bridge  
add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes   
comment=“” disabled=no forward-delay=15s max-message-age=20s mtu=1500   
name=Bridge\_VLAN priority=0x8000 protocol-mode=none  
transmit-hold-count=6

/interface ethernet  
set 0 arp=enabled auto-negotiation=yes cable-settings=default comment=  
Internet disable-running-check=yes disabled=no full-duplex=no   
mac-address=00:0C:42:02:37:80 mtu=1500 name=F0/0 speed=100Mbps  
set 1 arp=enabled auto-negotiation=yes cable-settings=default comment=  
“VLAN Trunk to Cisco Switch - Port on Bridge\_VLAN” disable-running-check=yes   
disabled=no full-duplex=yes mac-address=00:0C:42:02:37:81 mtu=1500 name=  
F0/1 speed=100Mbps  
set 2 arp=enabled auto-negotiation=yes cable-settings=default comment=  
“To DMZ” disable-running-check=yes disabled=no full-duplex=no   
mac-address=00:0C:42:02:37:82 mtu=1500 name=F0/2 speed=1Gbps  
set 3 arp=enabled auto-negotiation=yes cable-settings=default comment=“To a Computer”   
disable-running-check=yes disabled=no full-duplex=yes mac-address=  
00:0C:42:02:37:83 mtu=1500 name=F0/3 speed=100Mbps

/interface vlan  
add arp=enabled comment=“” disabled=no interface=Bridge\_VLAN mtu=1500 name=  
VLAN2 vlan-id=2

/ip pool  
add name=“LAN IP Pool” ranges=10.100.1.64/26

/ip dhcp-server  
add address-pool=“LAN IP Pool” always-broadcast=yes authoritative=  
after-2sec-delay bootp-support=static disabled=no interface=Bridge\_VLAN   
lease-time=5m name=“DHCP VLAN Bridge”

/interface bridge port  
add bridge=Bridge\_VLAN comment=RG disabled=no edge=auto external-fdb=auto   
horizon=none interface=F0/3 path-cost=10 point-to-point=auto priority=  
0x80  
add bridge=Bridge\_VLAN comment=“” disabled=no edge=auto external-fdb=auto   
horizon=none interface=F0/1 path-cost=10 point-to-point=auto priority=  
0x80

/interface bridge settings  
set use-ip-firewall=yes use-ip-firewall-for-vlan=yes

/ip address  
add address=10.100.1.1/24 broadcast=10.100.1.255 comment=LAN disabled=no   
interface=Bridge\_VLAN network=10.100.1.0 add address=10.100.2.1/24   
broadcast=10.100.2.255 comment=Server disabled=no interface=VLAN2   
network=10.100.2.0

/ip dhcp-server network  
add address=10.100.1.0/24 comment=LAN dhcp-option=“Node Type M-node”   
dns-server=10.100.1.1 domain=mydomain gateway=10.100.1.1 netmask=24   
wins-server=10.30.1.50

---

_[View the full topic](https://forum.mikrotik.com/t/configuring-vlan-trunking-on-mt-router-to-cisco-c2924-switch/21509)._
