Where is manual for crs125?
I saw examples about simple vlans but syntax needs to be updated in this example,
Where is additional instructions, there are so many tabs in routeos switch menu
We need documentation,
Can someone provide configuration commands needed to setup isolated private vlans?
Mikrotik, please provide complete switching manual to us
We are working on complete manual for CRS, it will be available very soon with configuration examples and description about the features.
Great Sergejs, CRS125 seems pretty interesting product, please try to include DHCP snooping,IP source guard, port security and dynamic arp inspection if they are not already.. These are must have features of all high-quality switches
Where is manual? is it ready?
no 
We have the same problem. Taging with isolated VLANs not working. (latest 6.8rc1) 
Need complete manual
When???
it looks like ROS for CRS125 is so not functional; they are not able to document any new features as yet.
we are also sitting on a stock of 20 new CRS125 which should be deployed with private VLAN’s and some basic bridging features.
Normis promise - documentation this week
I need manual for CRS too. Is it ready?
I send this question to support@mikrotik.com, but no reply.
I need manual for CRS too. Is it ready?
I send this question to support@mikrotik.com, but no reply.
it is now on wiki
http://wiki.mikrotik.com/wiki/Manual:CRS_features
http://wiki.mikrotik.com/wiki/Manual:CRS_examples
Thanx.
In examples I need to see how configure port-based tagged vlans.
For example:
tagged vlan 200, 300, 400 in port1.
tagged vlan 200 out port 2 only
tagged vlan 300 out port 3 only
tagged vlan 400 out port 4 only
Etc.
I tested on CRS RouterOS 6.5 (factory installed) and 6.9 (latest at this time). I don`t know, how to do this.
P.S. Sorry for my poor english.
P.P.S. All traffic sometimes blocked (switch is unavailable from any port) after change most parameters of switch and restored after hardware reset. This is not good.
Anyone have any ideas, how to route tagged vlans from one port to another?
Nope. Right now or seems like a device that was released without being finished.
Sent from my SCH-I545 using Tapatalk
These examples seems quite strange to me.
In the port based VLAN section its just used ingress-vlan-translation and egress-vlan-translation. I assume this is what IEEE calls VID translation (12.13.2 in IEEE Std 802.1Q™2011) and this is a mapping of S-VIDs which is in use when running a provider bridge (S-VLAN component). Running a C-VLAN component this table is not in use (5.5 in IEEE Std 802.1Q™2011).
In some transport scenarios the examples are relevant, but if we want to use the device as a “regular switch” with VLANs using 8100 tag on a LAN I don’t see this examples as relevant.
I’m playing around with my two switches, but it could be rather useful with some usecases and samples where the CSR is used as regular C-VLAN component and as a S-VLAN component.
Regards
Arne
I planned to use CRS as ordinary L2 managed switches. VLAN-s must be routed in group of marked ports without any changes (tag, untag, translation, mirroring, etc.). And block to any other ports. Very simple variant.
How to do this?
I’m waiting for this also.
Sent from my SCH-I545 using Tapatalk
Dear Mikrotik!
The time is going, but I have no answer for my question. My boss is very dissatisfied and say to me: “You must find alternative for all Mikrotik devices, because these devices have some bugs and dont have proper documentation”.
This is several hundreds devices (CCR, SXT, CRS, various RB series) used in our network now, and hundreds / thousands, planned for buy in the future.
That I should answer him?
Contact support directly and have them show you how to configure them. Then come tell us.
Message to support sent via email. Waiting.
I already addressed in a support over CRS manual, not received a reply quickly, within 5 or 6 days.