Hello,
We have CRS328-24P-4S+ running Mikrotik version 7.10.2 we are getting Tx Drop anyone facing same issue?
Regards
Any Idea?
Sure…after you provide some additional information:
- what version were you running before?
- had the same problem with previous OS?
- what is the percentage drops in regards to the traffic?
- is it on an interface (and have you checked wire?
- what does your config look like?
what version were you running before?
-Before we was on v6.49.8 long term.
had the same problem with previous OS?
- Yes
what is the percentage drops in regards to the traffic?
Tx Unicast: 330541201
Tx Broadcast: 85454
Tx Multicast: 82283
Tx Drop: 448
is it on an interface (and have you checked wire?
Tested on both interfaces SFP and Ethernet
what does your config look like?
/interface bridge
name=bridge1
/interface ethernet
set [ find default-name=ether1 ] poe-out=off
set [ find default-name=ether2 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether3 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether4 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether5 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether6 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether7 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether8 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether9 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether10 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether11 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether12 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether13 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether14 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether15 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether16 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether17 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether18 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether19 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether20 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether21 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether22 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether23 ] poe-out=forced-on poe-voltage=low
set [ find default-name=ether24 ] poe-out=forced-on poe-voltage=low
set [ find default-name=sfp-sfpplus1 ] auto-negotiation=no
set [ find default-name=sfp-sfpplus2 ] auto-negotiation=no
set [ find default-name=sfp-sfpplus3 ] auto-negotiation=no
set [ find default-name=sfp-sfpplus4 ] auto-negotiation=no
/interface vlan
add interface=bridge1 name=vlan61 vlan-id=61
/interface list
add exclude=dynamic name=discover
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/queue interface
set ether1 queue=ethernet-default
set ether2 queue=ethernet-default
set ether3 queue=ethernet-default
set ether4 queue=ethernet-default
set ether5 queue=ethernet-default
set ether6 queue=ethernet-default
set ether7 queue=ethernet-default
set ether8 queue=ethernet-default
set ether9 queue=ethernet-default
set ether10 queue=ethernet-default
set ether11 queue=ethernet-default
set ether12 queue=ethernet-default
set ether13 queue=ethernet-default
set ether14 queue=ethernet-default
set ether15 queue=ethernet-default
set ether16 queue=ethernet-default
set ether17 queue=ethernet-default
set ether18 queue=ethernet-default
set ether19 queue=ethernet-default
set ether20 queue=ethernet-default
set ether21 queue=ethernet-default
set ether22 queue=ethernet-default
set ether23 queue=ethernet-default
set ether24 queue=ethernet-default
set sfp-sfpplus1 queue=ethernet-default
set sfp-sfpplus2 queue=ethernet-default
set sfp-sfpplus3 queue=ethernet-default
set sfp-sfpplus4 queue=ethernet-default
/interface bridge port
add bridge=bridge1 interface=ether1
add bridge=bridge1 interface=ether2
add bridge=bridge1 interface=ether3
add bridge=bridge1 interface=ether4
add bridge=bridge1 interface=ether5
add bridge=bridge1 interface=ether6
add bridge=bridge1 interface=ether7
add bridge=bridge1 interface=ether8
add bridge=bridge1 interface=ether9
add bridge=bridge1 interface=ether10
add bridge=bridge1 interface=ether11
add bridge=bridge1 interface=ether12
add bridge=bridge1 interface=ether13
add bridge=bridge1 interface=ether14
add bridge=bridge1 interface=ether15
add bridge=bridge1 interface=ether16
add bridge=bridge1 interface=ether17
add bridge=bridge1 interface=ether18
add bridge=bridge1 interface=ether19
add bridge=bridge1 interface=ether20
add bridge=bridge1 interface=ether21
add bridge=bridge1 interface=ether22
add bridge=bridge1 interface=ether23
add bridge=bridge1 interface=ether24
/ip neighbor discovery-settings
set discover-interface-list=discover
/interface list member
add interface=vlan61 list=discover
/ip address
add address=10.0.61.46/24 interface=vlan61 network=10.0.61.0
/ip route
add distance=1 gateway=10.0.61.1
/ip service
set telnet disabled=yes
set ftp disabled=yes
set ssh disabled=yes
set api disabled=yes
set api-ssl disabled=yes
/system routerboard settings
set boot-os=router-os
[admin@MikroTik] >
P.S.: Now We are downgraded the switch to v6.49.8 long term again, Ethernet 1 the main link we have very simple configuration on the switch it’s just an access switch. We are getting more TX Drop when using queue=only-hardware-queue
Regards
I seem to be seeing this same thing but on a CRS326-24G.
Similar bridge setup and tx drops. Happening on 2 switches on the SFP+ interfaces. I do see some on copper interfaces as well, but not nearly as many as the SFP+ interfaces. 65 tx drops in under 30 min of runtime. No rx drops though, rx is running clean. Just seems to be tx.
Hello,
Any fix about above issue?
Tested v7.15.2 still have TX drops.
What is connected to the ports you are seeing drops in?
Out of curiosity I checked a CRS326-24G-2S+ that’s in use as a server switch here and sure enough I am seeing TX drops however only on 4 interfaces. The devices connected to these 4 interfaces are all Proxmox servers.
All 4 ports are vlan trunks. As these are the only ports on the switch with TX drops I’m inclined to think it’s a client issue rather than a switch issue and that Proxmox might be the issue.
I also have a CRS328-24P-4S+ and no ports are showing TX drops.
The CRS326 is running 7.15.2
The CRS328 is running 7.15.1
Hello,
Mikrotik PowerBox’s with 100Mbps port are connected to ports.