Hello everyone.
I’ve been reading the forum and looking for some situation like mine and I’ve found some, but as I’m not obtaining the results I expected I’ve decided to open a new message, so if you can help me I would be very grateful.
First of all let me introduce my situation and equipment.
My ISP provide me a 300/30Mbps Internet connection, and the goal is to obtain the bests results possible in a 200 - 250 meter with direct view between antennas.
The equipment is, 2x Mikrotik RBSXTG-5HPacD-SA, so they are a SXT ac antennas which (theoretically) have a 866Mbps transfer rate.
The setup I followed for the link are here: http://www.wispforum.net/entry.php?6-How-to-Connect-two-Mikrotik-SXT-5D-s-In-Bridge-Mode-Part-II&goto=prev and http://www.wispforum.net/entry.php?6-How-to-Connect-two-Mikrotik-SXT-5D-s-In-Bridge-Mode-Part-II
Having concerned that I have a short distance between points, I don’t know if my results are the best possible and I will be happy if you help me to interpret the results and to setup the equipment, because now I’m lost in a sea of configuration options.
Now let me to show you some information about my config, tests, and status of the antennas.
AP Side configuration:
[admin@MikroTik] > interface wireless print advanced
Flags: X - disabled, R - running
0 R name="wlan1" mtu=1500 mac-address=XX:XX:XX:XX:XX arp=enabled
disable-running-check=no interface-type=Atheros AR9888
radio-name="XXXXXXXXXX" mode=bridge ssid="MikroTik" area=""
frequency-mode=manual-txpower country=spain antenna-gain=0 frequency=
band=5ghz-onlyac channel-width=20/40/80mhz-eeeC scan-list=default
wireless-protocol=802.11 rate-set=default
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54
basic-rates-a/g=6Mbps max-station-count=2007 distance=dynamic
tx-power-mode=default dfs-mode=none vlan-mode=no-tag vlan-id=1
wds-mode=dynamic wds-default-bridge=bridge1 wds-default-cost=100
wds-cost-range=50-150 wds-ignore-ssid=no update-stats-interval=disabl
bridge-mode=enabled default-authentication=yes default-forwarding=yes
default-ap-tx-limit=0 default-client-tx-limit=0
proprietary-extensions=post-2.9.25 wmm-support=enabled hide-ssid=yes
security-profile=default disconnect-timeout=3s on-fail-retry-time=100
preamble-mode=both compression=no allow-sharedkey=no
station-bridge-clone-mac=00:00:00:00:00:00 ampdu-priorities=0
guard-interval=any
ht-supported-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-
9,mcs-10,mcs-11,mcs-12,mcs-13,mcs-14,mcs-15,mcs-16,mcs-17,
18,mcs-19,mcs-20,mcs-21,mcs-22,mcs-23
ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7
https://www.dropbox.com/s/qg822quvv8hkgp2/ap_1.PNG?dl=0
https://www.dropbox.com/s/fbs24gugvqv7gt0/ap_2.PNG?dl=0
(I am using 802.11 protocol because I’m making tests).
Now in the client side:
[admin@MikroTik] > interface wireless print advanced
Flags: X - disabled, R - running
0 R name="wlan1" mtu=1500 mac-address=XX:XX:XX:XX:XX arp=enabled
disable-running-check=no interface-type=Atheros AR9888
radio-name="XXXXXXXXXX" mode=station-bridge ssid="MikroTik" area=""
frequency-mode=manual-txpower country=spain antenna-gain=0 frequency=5700
band=5ghz-onlyac channel-width=20/40/80mhz-eeeC scan-list=default
wireless-protocol=802.11 rate-set=default
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps
basic-rates-a/g=6Mbps max-station-count=2007 distance=dynamic
tx-power-mode=default dfs-mode=none vlan-mode=no-tag vlan-id=1
wds-mode=dynamic wds-default-bridge=bridge1 wds-default-cost=100
wds-cost-range=50-150 wds-ignore-ssid=no update-stats-interval=disabled
bridge-mode=enabled default-authentication=yes default-forwarding=yes
default-ap-tx-limit=0 default-client-tx-limit=0
proprietary-extensions=post-2.9.25 wmm-support=enabled hide-ssid=no
security-profile=default disconnect-timeout=3s on-fail-retry-time=100ms
preamble-mode=both compression=no allow-sharedkey=no
station-bridge-clone-mac=00:00:00:00:00:00 ampdu-priorities=0
guard-interval=any
ht-supported-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-
9,mcs-10,mcs-11,mcs-12,mcs-13,mcs-14,mcs-15,mcs-16,mcs-17,mcs-
18,mcs-19,mcs-20,mcs-21,mcs-22,mcs-23
ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7
https://www.dropbox.com/s/pkcll8oz80dhwas/client_1.JPG?dl=0
https://www.dropbox.com/s/o0vtiva3txm3aa5/client_2.JPG?dl=0
Now the tests:
https://www.dropbox.com/s/a4qprqe2s6dgxgg/TEST_CLIENT.JPG?dl=0
https://www.dropbox.com/s/cmyx588qzu112do/TEST_CLIENT_UDP.JPG?dl=0
So what do you think about the tests and the results. How can I improve performance?.
Thank you very much for your help and answers, hope you can help me.