There is a problem on RB4011 on wifi 5Ghz. CAPSMAN mode or not.
When a client transitions from RB4011 wifi 5ghz to another device, the physical interface 5ghz crash. Enable only reload.
While seen only with the iPhone XS, XS Max, new iPad Pro. This is a problem only on RB4011.
So it was up to 6.44. You have not fixed this problem. Sent you the supout.rif file to the support@mikrotik.com, Ticket#2019022722003126
Can you please explain the issue a bit more? I have upgraded all of my devices to 6.44 except our core router. 5GHz @ 80 MHz xxxx is now enabled on all APs. I have only one RB4011 (which happens to be located in my office). I have been moving in and out of 9 AP zones from being attached to the RB4011, and have not noticed anything abnormal. Maybe I am not looking in the right place, but no interface crash is apparent. Using an XsMax.
Good day,
I noticed it this morning. My iPhone XS Max was connected to RB4011 5ghz. I went with him to another room where the RB962 stands. The phone logs successfully switched.
When I returned to the RB4011 coverage area, I found that the 5ghz interface had fallen on wifi network monitoring. He was active in the system.
Then I overloaded RB4011 and repeated the experiment, the same thing happened, 5ghz on RB4011 crash.
RB4011 operated at a frequency of 5300, RB962 at a frequency of 5180.
After I removed RB4011 from CAPSMAN and tested it again. The situation repeated - 5ghz crash. I took the dump and sent it to mikrotik.
I discovered the following, if RB4011 and RB962 are set to the same frequency, the interface of RB4011 does not crash.
Mikrotik, what news?
TimurA, what news? Did you get an email response?
Chupaka, Silence, no answer.
I have not seen this issue in my environment. We only have one RB4011 (w/ radios and running 6.44 stable), and 9 various other Mikrotik APs. I don’t see anything in the logs that suggest an interface has crashed.
Has anyone else been able to reproduce this problem?
This only happens with iPhone XS, XS Max, iPad Pro 2018, when it reconnects from a separate device to another. RB4011 5Ghz is falling.
@normis said create a new topic. (radios and running 6.44)
I should have mentioned that I am not seeing this on our iPhones XsMax or Xs. I just moved from being connect to an hAP to our RB4011, then into an area with a cAP and back to the RB4011. I did not see anything unusual.
Maybe I am not looking in the proper place.
Can you show me what the log entry looks like when the interface crashes?
I just did a test:::…
All examples using 5Ghz 20/40/80Mhz A/N/AC, XXXX center channels and everything running at 6.44 stable. The SSID name (WB-AP) is the same for all. Tested with an iPhone XsMax (IOS 12.1.4)
I started off connecting to an OmniTIk (RBOmniTIKPG-5HacD). No problem. Then I connected to a hAP (RBwAPG-5HacT2HnD). No problem. Then I connected to a cAP (RBcAPGi-5acD2nD), still no problem. Finally I connected to an RB4011 (RB4011iGS+5HacQ2HnD-IN-US)… no problem. I did not do anything but move into the range of each device so that my iPhone would disconnect from one and connect to the next one… The RB4011 log does not show anything abnormal.
If there is an issue, I am not personally able to reproduce it… so I need to understand what you are seeing a little better.
Make a different frequency on the RB4011, different from other devices. See how the interface crashes on RB4011. And IPv6, dual-stack on iPhone XS Max
if you need video of the interface crash, I can send it to the mail. Do not publicly spread.
RB4011 frequency 5260, RB962 frequency 5180. iPhone XS Max switched to RB962, then switches to RB4011 and 5ghz falls. My computer also shuts down from RB4011. If you use the range in the network 5180-5240 - the departure does not occur. Something with a central channel on RB4011. RB962 insures the central channel is obtained if you use 5180-5240 frequency. If RB4011 use different central channel of RB962 then 5ghz on RB4011 crash.
Now in capsman RB4011 stood at 5240, RB962 stood at 5180. After 10 minutes of operation, RB4011 fell. IPv4 / IPv6.
So it’s not a problem in the central channel.
RB4011 only works steadily if RB962 and RB4011 are on the same channel.
the screen shows that 5ghz from RB4011 is not, crash.
In general - the problem device RB4011. I do not recommend, already tired of being a tester for 2 months.
I see what you are saying.
We have a full dual stack environment as well. All of our radios are set to “auto” for the frequencies and auto (XXXX) for the center channels. Maybe that is why we are not having any issues? We are stuck with US channel space.
What app are you using on your Mac to scan the frequencies?
Tested in XXXX and carried the channel Ceee, eCeee - in different ways. The frequency of the channel is fixed set, without auto.
I was looking for any compromise, but the RB4011 is stable, then when the frequency coincides with the device from another room
use this link - https://itunes.apple.com/us/app/wifi-explorer/id494803304
Run netinstall 6.44 on RB4011, did not help. The problem is either in ROS or in the device.
Well, I have a much more simple environment than @TimurA and I am having issues with the rb4011 wifi as well. I haven’t yet been able to isolate the cause but I get similar entries in my logs as it seems you experience when it happens.
I now agree. I am seeing strange behavior on the RB4011, but only with the new Apple devices. uggggg…
Today, the MSI laptop on Windows 10, when copying a large amount of data, has crash 5ghz, four times in a row.
terrible device RB4011, and no timing fixes.
funny, RB962 doesn’t have such problems, if RB4011 crashes even with Windows 10, then RB962 at 5ghz does the same thing without any problems. No matter Apple, Microsoft.