I cannot get my Hotspot to work. Whenever I try to do anything through http port 80 it says this page cannot be displayed. I can ping and stuff but no http. http://192.168.1.190:80/ where hotspot should be running does not come up either. Can anyone tell me what is wrong? This is 2.8.13 release level 5 on a Soekris SBC with Prism card. The range on my Prism 200mw card with a stubby antenna only appears to be a few feet but I think that is a different issue.
Matt
[admin@MikroTik] > export
aug/21/2004 15:22:50 by RouterOS 2.8.13
software id = TFPB-1LT
/ interface ethernet
set ether1 name=“ether1” mtu=1500 arp=enabled disable-running-check=yes auto-negotiation=yes full-duplex=yes
long-cable=no speed=100Mbps disabled=no
set ether2 name=“ether2” mtu=1500 arp=enabled disable-running-check=yes auto-negotiation=yes full-duplex=yes
long-cable=no speed=100Mbps disabled=no
set ether3 name=“ether3” mtu=1500 arp=enabled disable-running-check=yes auto-negotiation=yes full-duplex=yes
long-cable=no speed=100Mbps disabled=no
/ interface wireless
set wlan1 name=“wlan1” mtu=1500 arp=enabled disable-running-check=no mode=ap-bridge ssid=“seneca.hot.bbwi.net”
frequency=2412 band=2.4GHz-B scan-list=default-ism supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps
supported-rates-a/g=“” basic-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps basic-rates-a/g=“” max-station-count=2007
fast-frames=no dfs-mode=none antenna-mode=ant-a wds-mode=disabled wds-default-bridge=none wds-ignore-ssid=no
default-authentication=yes default-forwarding=no hide-ssid=no 802.1x-mode=none disabled=no
/ interface wireless security
set wlan1 security=none algo-0=none key-0=“” algo-1=none key-1=“” algo-2=none key-2=“” algo-3=none key-3=“”
transmit-key=key-0 sta-private-algo=none sta-private-key=“” radius-mac-authentication=no
/ interface wireless align
set frame-size=300 active-mode=yes receive-all=no audio-monitor=00:00:00:00:00:00 filter-mac=00:00:00:00:00:00
ssid-all=no frames-per-second=25 audio-min=-100 audio-max=-20
/ interface bridge port
set ether1 priority=128 path-cost=10
set ether2 bridge=none priority=128 path-cost=10
set ether3 bridge=none priority=128 path-cost=10
set wlan1 bridge=none priority=128 path-cost=10
/ ip pool
add name=“hs-pool-real” ranges=10.5.50.2-10.5.50.254
/ ip accounting
set enabled=no threshold=256
/ ip accounting web-access
set accessible-via-web=no address=0.0.0.0/0
/ ip address
add address=192.168.1.190/24 network=192.168.1.0 broadcast=192.168.1.255 interface=ether1 comment=“added by setup”
disabled=no
add address=10.5.50.1/24 network=10.5.50.0 broadcast=10.5.50.255 interface=wlan1 comment=“hotspot network” disabled=no
/ ip arp
/ ip dns
set primary-dns=12.127.16.68 secondary-dns=12.127.17.72 allow-remote-requests=yes cache-size=“2048 kB” cache-max-ttl=7d
/ ip firewall
set input name=“input” policy=accept comment=“”
set forward name=“forward” policy=accept comment=“”
set output name=“output” policy=accept comment=“”
add name=“hotspot-temp” policy=none comment=“limit unauthorized hotspot clients”
add name=“hotspot” policy=none comment=“account authorized hotspot clients”
/ ip firewall rule forward
add in-interface=wlan1 action=jump jump-target=hotspot-temp comment=“limit access for unauthorized hotspot clients”
disabled=no
add action=jump jump-target=hotspot comment=“account traffic for authorized hotspot clients” disabled=no
/ ip firewall rule hotspot-temp
add flow=hs-auth action=return comment=“return, if connection is authorized” disabled=no
add protocol=icmp action=return comment=“allow ping requests” disabled=no
add dst-address=:53 protocol=udp action=return comment=“allow dns requests” disabled=no
add action=reject comment=“reject access for unauthorized hotspot clients” disabled=no
/ ip firewall rule input
add in-interface=wlan1 dst-address=:80 protocol=tcp action=jump jump-target=hotspot comment=“account traffic from hotspot
clients to hotspot servlet” disabled=no
add in-interface=wlan1 dst-address=:80 protocol=tcp action=accept comment=“accept requests for hotspot servlet”
disabled=no
add in-interface=wlan1 dst-address=:67 protocol=udp action=accept comment=“accept requests for local DHCP server”
disabled=no
add in-interface=wlan1 action=jump jump-target=hotspot-temp comment=“limit access for unauthorized hotspot clients”
disabled=no
/ ip firewall rule output
add src-address=:80 out-interface=wlan1 protocol=tcp action=jump jump-target=hotspot comment=“account traffic from
hotspot servlet to hotspot clients” disabled=no
/ ip firewall dst-nat
add dst-address=:53 protocol=udp action=redirect comment=“intercept all DNS requests” disabled=no
add in-interface=wlan1 protocol=tcp flow=!hs-auth action=redirect to-dst-port=80 comment=“redirect unauthorized hotspot
clients to hotspot service” disabled=no
add in-interface=wlan1 dst-address=:80 protocol=tcp action=redirect to-dst-port=80 comment=“transparent HTTP proxy for
hotspot clients” disabled=no
/ ip firewall service-port
set ftp ports=21 disabled=no
set pptp disabled=no
set gre disabled=no
set h323 disabled=yes
set mms disabled=no
set irc ports=6667 disabled=no
set quake3 disabled=no
set tftp ports=69 disabled=no
/ ip firewall src-nat
add src-address=10.5.50.0/24 action=masquerade comment=“masquerade hotspot network” disabled=no
/ ip firewall connection tracking
set enabled=yes tcp-syn-sent-timeout=2m tcp-syn-received-timeout=1m tcp-established-timeout=5d tcp-fin-wait-timeout=2m
tcp-close-wait-timeout=1m tcp-last-ack-timeout=30s tcp-time-wait-timeout=2m tcp-close-timeout=10s udp-timeout=30s
udp-stream-timeout=3m icmp-timeout=30s generic-timeout=10m
/ ip neighbor discovery
set ether1 discover=no
set ether2 discover=no
set ether3 discover=yes
set wlan1 discover=yes
/ ip route
add dst-address=0.0.0.0/0 preferred-source=0.0.0.0 gateway=192.168.1.1 distance=1 comment=“added by setup” disabled=no
/ ip service
set telnet port=23 address=0.0.0.0/0 disabled=no
set ftp port=21 address=0.0.0.0/0 disabled=no
set www port=81 address=0.0.0.0/0 disabled=no
set hotspot port=80 address=0.0.0.0/0 disabled=no
set ssh port=22 address=0.0.0.0/0 disabled=no
set hotspot-ssl port=443 address=0.0.0.0/0 certificate=none disabled=no
/ ip socks
set enabled=no port=1080 connection-idle-timeout=2m max-connections=200
/ ip policy-routing
/ ip policy-routing rule
add src-address=0.0.0.0/0 dst-address=0.0.0.0/0 flow=“” interface=all action=lookup table=main comment=“” disabled=no
/ ip policy-routing table main
add dst-address=0.0.0.0/0 gateway=192.168.1.1 preferred-source=0.0.0.0 comment=“added by setup” disabled=no
/ ip upnp
set enabled=no
/ ip dhcp-client
set enabled=no host-name=“” client-id=“” add-default-route=yes use-peer-dns=yes
/ ip dhcp-server
add name=“hs-dhcp-server” interface=wlan1 lease-time=1h address-pool=hs-pool-real add-arp=no authoritative=no disabled=no
/ ip dhcp-server network
add address=10.5.50.0/24 gateway=10.5.50.1 comment=“hotspot network”
/ ip hotspot
set use-ssl=no hotspot-address=10.5.50.1 dns-name=“seneca.hotspot.bbwi.net” status-autorefresh=1m universal-proxy=yes
parent-proxy=0.0.0.0:0 auth-requires-mac=yes auth-mac=no auth-mac-password=no auth-http-cookie=no
http-cookie-lifetime=1d allow-unencrypted-passwords=no login-mac-universal=no split-user-domain=no
/ ip hotspot profile
set default name=“default” shared-users=1 mark-flow=“hs-auth” login-method=enabled-address keepalive-timeout=2m
/ ip hotspot user
add name=“test” password=“test” profile=default comment=“” disabled=no
/ ip hotspot aaa
set use-radius=no accounting=yes interim-update=0s
/ ip hotspot universal
add interface=wlan1 idle-timeout=5m arp=all-arp use-dhcp=yes addresses-per-mac=2 comment=“” disabled=no
/ ip hotspot universal service-port
set ftp ports=21 disabled=no
/ ip ipsec proposal
add name=“default” auth-algorithms=sha1 enc-algorithms=3des lifetime=30m lifebytes=0 pfs-group=modp1024 disabled=no
/ system identity
set name=“MikroTik”
/ system logging
set default-remote-address=0.0.0.0 default-remote-port=514 disk-buffer-lines=100 memory-buffer-lines=100
/ system logging facility
set Firewall-Log local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set System-Info local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set System-Error local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set System-Warning local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set Hotspot-Account local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set Hotspot-Info local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set Hotspot-Error local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set IPsec-Event local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set IKE-Event local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set IPsec-Warning local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
set System-Echo local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=yes
set Wireless-Info local=memory remote=none remote-address=0.0.0.0 remote-port=0 prefix=“” echo=no
/ system serial-console
set enabled=yes port=serial0
/ system upgrade mirror
set enabled=no primary-server=0.0.0.0 secondary-server=0.0.0.0 check-interval=1d user=“”
/ system watchdog
set reboot-on-failure=yes watch-address=none watchdog-timer=yes ping-start-after-boot=5m
/ system ntp client
set enabled=yes mode=unicast primary-ntp=192.43.244.18 secondary-ntp=0.0.0.0
/ system ntp server
set enabled=no broadcast=no multicast=no manycast=yes
/ port
set serial0 name=“serial0” baud-rate=9600 data-bits=8 parity=none stop-bits=1 flow-control=none
set serial1 name=“serial1” baud-rate=9600 data-bits=8 parity=none stop-bits=1 flow-control=none
/ queue type
set default name=“default” kind=pfifo bfifo-limit=15000 pfifo-limit=50 red-limit=60 red-min-threshold=10
red-max-threshold=50 red-burst=20 sfq-perturb=5 sfq-allot=1514 pcq-rate=0 pcq-limit=50 pcq-classifier=“”
set ethernet-default name=“ethernet-default” kind=pfifo bfifo-limit=15000 pfifo-limit=50 red-limit=60
red-min-threshold=10 red-max-threshold=50 red-burst=20 sfq-perturb=5 sfq-allot=1514 pcq-rate=0 pcq-limit=50
pcq-classifier=“”
set wireless-default name=“wireless-default” kind=sfq bfifo-limit=15000 pfifo-limit=50 red-limit=60 red-min-threshold=10
red-max-threshold=50 red-burst=20 sfq-perturb=5 sfq-allot=1514 pcq-rate=0 pcq-limit=50 pcq-classifier=“”
set synchronous-default name=“synchronous-default” kind=red bfifo-limit=15000 pfifo-limit=50 red-limit=60
red-min-threshold=10 red-max-threshold=50 red-burst=20 sfq-perturb=5 sfq-allot=1514 pcq-rate=0 pcq-limit=50
pcq-classifier=“”
/ user
add name=“admin” group=full address=0.0.0.0/0 comment=“system default user” disabled=no
/ user group
add name=“read” policy=local,telnet,ssh,!ftp,reboot,read,!write,!policy,test,web
add name=“write” policy=local,telnet,ssh,!ftp,reboot,read,write,!policy,test,web
add name=“full” policy=local,telnet,ssh,ftp,reboot,read,write,policy,test,web
/ user aaa
set use-radius=no accounting=yes interim-update=0s default-group=read
/ driver
/ snmp
set enabled=no contact=“” location=“”
/ snmp community
set public name=“public” address=0.0.0.0/0 read-access=yes
/ tool bandwidth-server
set enabled=yes authenticate=yes allocate-udp-ports-from=2000 max-sessions=10
/ tool mac-server ping
set enabled=yes
/ tool sniffer
set interface=all only-headers=no memory-limit=10 file-name=“” file-limit=10 streaming-enabled=no
streaming-server=0.0.0.0 filter-stream=no filter-protocol=ip-only filter-address1=0.0.0.0/0:0-65535
filter-address2=0.0.0.0/0:0-65535
/ tool e-mail
set server=0.0.0.0 from=“<>”
[admin@MikroTik] >