I’m trying ti work with telit LE-910 -
I put data =3 , info =0
I can see the netwrok (LTE) and the sim is working
but I can’t connect to in - say “no network protocol”
any one know why ?
(when I connect the modem to the computer - everything is working , so it’s a RB issue…)
Thanks ,
Hey David1234
I could just make it work here!
I’m using 912UAG-2HPnD, RoS and Firmware version 6.41
From my side, I couldn’d find it as a LTE interface, but as a PPP client interface only, so:
a) I’ve changed the USB under the System > Routerboard > USB → change from USB Type A to Mini PCI-E;
b) After that, the RB identified under System > Resources > USB:
Vendor: Android - Vendor ID: 0x1bc7 - Device: Android - Device ID: 0x1201
(This is the only strange issue… Although it works, it’s identified as Android under this menu).
c) Under Interfaces > PPP Client, I used the following configuration:
c.1) General tab:
c.2) PPP tab
Enable the interface and apply the configurations.
After these, my RB initialized the modem, and could dial out and authenticate, and finally connected:
jan/01/2002 01:36:59 system,info device changed by admin
jan/01/2002 01:36:59 async,ppp,info ppp-out1: initializing…
jan/01/2002 01:36:59 async,ppp,info ppp-out1: waiting for packets…
jan/01/2002 01:37:08 async,ppp,info ppp-out1: connecting…
jan/01/2002 01:37:31 async,ppp,info Telit LE910-EUG: terminating…
jan/01/2002 01:37:31 async,ppp,info Telit LE910-EUG: disconnected
jan/01/2002 01:37:31 async,ppp,info Telit LE910-EUG: initializing…
jan/01/2002 01:37:31 async,ppp,info Telit LE910-EUG: reseting link…
jan/01/2002 01:37:31 system,info device changed by admin
jan/01/2002 01:37:32 async,ppp,info Telit LE910-EUG: initializing modem…
jan/01/2002 01:37:33 async,ppp,info Telit LE910-EUG: dialing out…
jan/01/2002 01:37:33 async,ppp,info Telit LE910-EUG: authenticated
jan/01/2002 01:37:36 async,ppp,info Telit LE910-EUG: could not determine remote address, using 10.112.112.
119
jan/01/2002 01:37:36 async,ppp,info Telit LE910-EUG: connected
PS.: I think the most important here is the Data and Info channel numbers.
Thanks you for all this
but I have allready try it
nothing .....
could not connect - not even try to dial out
I can see the network LTE -62dBm , not a problem
aslo in resource I can see it's telit
/system resource usb print
# DEVICE VENDOR NAME SPEED
0 1:1 Linux 3.3.5 ehci_hcd RB400 EHCI 480 Mbps
1 1:2 Telit FIH7160 480 Mbps
can you tell me what is the firmware of the modem you are using?
Thanks ,
,
From some reason when I don't write an apn - it's working
did you have this problem too?
Let’s divide in topics, to make it easier.
1- So, you’re not using PPP client, but LTE, right?
2- And are you using Telit LE910? I found strange that in your case, it identifies with Telit. In mine, it shows Android.
3- What’s the result for “System > Resources > USB” ? Which vendor ID and device ID does the system show?
4- For the modem firmware and the configuration without APN, I tell you later, because I’m not near the device right now to test. As soon as I go back, i let you know.
1- So, you’re not using PPP client, but LTE, right? using a ppp-client interface (but I can connect to the 4G LTE netwrok).
2- And are you using Telit LE910? I found strange that in your case, it identifies with Telit. In mine, it shows Android. Telit LE90-AU V2
3- What’s the result for “System > Resources > USB” ? Which vendor ID and device ID does the system show? Vendor “Telit” Name “FIH7160” device 1:2
4- For the modem firmware and the configuration without APN, I tell you later, because I’m not near the device right now to test. As soon as I go back, i let you know.
Thanks ,
Firmware version - 17.00.523 (Telit LE910-EUG V2)
Regarding the APN setting, you’re correct: even if I dont use it, it works and connects.
Also, I’ve change the info channel to 4, so: Data Channel 4 Info Channel 4, also works.
Which firmware version are you using?