Hello,
I just bought RB1000 and upgraded it to ROS v3.14 and now Terminal doesn’t work correctly but winbox works fine.
I don’t get LOGIN screen…
At first in Terminal RB1000 show message:
RouterBOOT booter 2.17
RouterBoard 1000
CPU frequency: 1333 MHz
Memory size: 512 MB
Press any key within 2 seconds to enter setup..
loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
Using RB1000 machine description
Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
Linux version 2.6.26.5 (build@builder2) (gcc version 4.2.1) #1 Tue Sep 16 09:39:
26 EEST 2008
Found initrd at 0x802b1000:0x802b2000
Found legacy serial port 0 for /soc8548@e0000000/serial@4500
mem=e0004500, taddr=e0004500, irq=0, clk=533328000, speed=0
console [udbg0] enabled
Entering add_active_range(0, 0, 131072) 0 entries of 256 used
Top of RAM: 0x20000000, Total RAM: 0x20000000
Memory hole size: 0MB
Zone PFN ranges:
DMA 0 -> 131072
Normal 131072 -> 131072
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 131072
On node 0 totalpages: 131072
DMA zone: 1024 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 130048 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: root=/dev/mtdblock1 console=ttyS0,115200 board=mpc85xx boot
=1
mpic: Setting up MPIC " OpenPIC " version 1.2 at e0040000, max 1 CPUs
mpic: ISU size: 1, shift: 0, mask: 0
mpic: Initializing for 32 sources
PID hash table entries: 2048 (order: 11, 8192 bytes)
time_init: decrementer frequency = 66.666000 MHz
time_init: processor frequency = 1333.320000 MHz
clocksource: timebase mult[3c00275] shift[22] registered
clockevent: decrementer mult[1111] shift[16] cpu[0]
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 516736k/524288k available (2528k kernel code, 7276k reserved, 96k data,
105k bss, 128k init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 133.12 BogoMIPS (lpj=665600)
Mount-cache hash table entries: 512
net_namespace: 628 bytes
NET: Registered protocol family 16
rstcr compatible register does not exist!
PCI: Probing PCI hardware
SCSI subsystem initialized
libata version 3.00 loaded.
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
Unpacking initramfs... done
Freeing initrd memory: 4k freed
beeper init
irq=31
beeper done
yaffs Sep 16 2008 09:34:42 Installing.
msgmni has been set to 1009
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 28) is a 16550A
console handover: b
oot [udbg0] -> real [ttyS0]
Gianfar MII Bus: probed
eth0: Gianfar Ethernet Controller Version 1.2, 00:0c:42:20:58:0c
eth0: Running with NAPI enabled
eth0: 256/256 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.2, 00:0c:42:20:58:0d
eth1: Running with NAPI enabled
eth1: 256/256 RX/TX BD ring size
eth2: Gianfar Ethernet Controller Version 1.2, 00:0c:42:20:58:0e
eth2: Running with NAPI enabled
eth2: 256/256 RX/TX BD ring size
eth3: Gianfar Ethernet Controller Version 1.2, 00:0c:42:20:58:0f
eth3: Running with NAPI enabled
eth3: 256/256 RX/TX BD ring size
Driver 'sd' needs updating - please use bus_type methods
RB_PPC CF
CF: using Local-Bus clock 133332 kHz 7500 ps
CF: irq level 1
scsi0 : pata_rb_ppc
ata1: PATA max PIO6 irq 29
CF PIO mode changed to 0
RB_PPC CF
CF: irq level 1
scsi1 : pata_rb_ppc
ata2: PATA max PIO6 irq 30
RB_PPC NAND
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 721 at 0x00b44000
Creating 2 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00400000 : "RouterBoard NAND Boot"
0x00400000-0x04000000 : "RouterBoard NAND Main"
Registered led device: user-led
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
yaffs: dev is 32505857 name is "mtdblock1"
yaffs: Attempting MTD mount on 31.1, "mtdblock1"
block 466 is bad
VFS: Mounted root (yaffs filesystem) readonly.
Freeing unused kernel memory: 128k init
Starting...
VFS: Can't find an ext2 filesystem on dev mtdblock0.
yaffs: dev is 32505856 name is "mtdblock0"
yaffs: Attempting MTD mount on 31.0, "mtdblock0"
NET: Registered protocol family 1
NET: Registered protocol family 17
flash: module license 'unspecified' taints kernel.
flash: starting...
flash: ptr = a1980000
flash_ioctl: get_flash_info(void)
flash_ioctl: get_soft_info(void)
flash: started
panicSaver: starting...
panicSaver: get_soft_ptr()=0x00010000
panicSaver: get_soft_size()=0x00001000
panicSaver: started
panicSaver_ioctl, cmd: 0x1, arg: 0x0
panicSaver_ioctl, cmd: 0x2, arg: 0x0
panicSaver_ioctl, cmd: 0x3, arg: 0x0
Starting services...
After downgrade to ROS v3.13 I got message:
RouterBOOT booter 2.16
RouterBoard 1000
CPU frequency: 1333 MHz
Memory size: 512 MB
Press any key within 2 seconds to enter setup..
loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
Starting...
Starting services...