ros 3.15 is out

Hardware MikroTik hardware general
1

What’s new in 3.15:

*) added workaround for non-standards compliant CPE with timestamp issue;
*) added ability to manage multiple disks & stores under /store;
*) added support for storing user-manager database on secondary media via /store;
*) /store should be used to set up secondary disk as web proxy cache;
*) added support for Mesh in WinBox;
*) fixed client roaming in mesh protocol;
*) fixed bug in MME routing protocol:
routes sometimes were lost from routing table;
*) fixed some bugs in routing-test;
*) fixed traffic forwarding when VRF (virtual routing and forwarding) is used;
*) fixed problem - USB did not work on Geode LX boards;
*) fixed problem - farsync cards did not negotiate links;
*) added support for Novatel EU870D;
*) added support for Intel 82575EB & 8257GB gigabit ethernet PCI-Express cards;
*) removed support for all synchronous cards but farsync;
*) graphing - all target (source) addresses displayed in queue statistics page;
*) bridge firewall broute table is removed - it did not work as expected anyway;
*) ingress-priority matcher added to bridge firewall
*) fixed use-dns property of console traceroute command, default now is
use-dns=no;
*) updated UK 5.8 FIXED regulatory domain info;
*) /system ssh now by default uses name of logged in user instead of “admin”;
*) fixed support for some microSD cards on RB400;
*) include Relay-Session-ID in packets sent by PPPoE client if required;
*) added ability to specify src. address for radius client;
*) dns cache - improved static entry behavior;
*) fixed dial-on-demand on ppp interfaces;

:stuck_out_tongue:

2

*) added ability to specify src. address for radius client;

Can this also be added for l2tp-client? And ntp-client?

And snmp server? Please fix snmp server so it replies using the original requested address!

Sam

3

speed.jpg
very cool speed with 3.15 - even more then the eths are built for on the rb532 ;-))
this showed at least as log as it took me to see it and make a screenshot …
it has slowed down again ;-(

4

Heads up…I upgraded a 532 which is just running a hotspot service and no other special settings and it’s randomly hanging and being rebooted by the watchdog. Went from 3.14 to 3.15, no problems with 3.14.

5

Thanks for the traceroute fix!

6

And the client roaming for mesh interfaces!

7

First freqeuncy now is 5735 instead of 5740
So you will need to modify the scan-lists.

8

and what about kernel failure messages?
i still got them…
:stuck_out_tongue:

and where is changelog for bios 2.18?

9

I think this has been buggy since 3.10, it happens especially when the unit is rebooted, last for about < 1minute :confused:

any fixes in the future?

10

Was the queue-breakage-with-xen-installed issue fixed?

A quick look around hasn’t found me any mesh documentation except for the old rstp method.

11

http://wiki.mikrotik.com/wiki/Layer-2_routing_for_Mesh_networks

12

Thank you! This looks very exciting. I think this may help a lot of the weirdness I see with our RSTP setups.

13

I also upgraded 16 532 that are running hotspot service it’s randomly hanging and processor goes 100% and stays there. It took up to 3 days for all them to fail. Traffic goes slow and no winbox. I reboot and all is well for short time. Went from 3.14 to 3.15, no problems with 3.14. I downgraded to 3.10 to get stable. Any one have any idea? Also I updated to 2.16 RouterBOOT and it didnt help.

14

Nice one with the Radius source address =) thanks guys.. i feel a network wide upgrade is in order.

15

i have the same problem here with hotspot + radius + rb450 , the cpu goes 100% and them the watchdog reboots but without sending the radius accounting information about disconnect. so all my clients get stuck on my freeradius..
yesterday downgraded to 3.13 and everything get stable again..

16

i have the same problem here with hotspot + freeradius + radiusmanager + rb450.
Downgraded to 3.13 too.
'Smell" like stable now…