RouterBoard 564 problem

Hardware MikroTik hardware general
1

I just purchased a RB532A with a RB 564 Daughterboard.

I installed 2.9.25 an when i issue the following command in terminal window:

/interface ethernet print

i get:

**Flags: X - disabled, R - running

NAME MTU MAC-ADDRESS ARP

0 R ether1 1500 00:0C:42:04:AF:59 enabled
1 R ether2 1500 00:0C:42:04:AF:5A enabled
2 R ether3 1500 00:0C:42:04:AF:5B enabled**

Where is the other 6 ports?

When i plug a UTP cable in to the upper 6 slots the corresponding led is blinking…

Also I tried to unplug the daughterboard and plug it again.. it seems firmly plugged.

From the BOOTRom menu i get

Board Info:

Board type: 532A
Serial number: 0B8301D9F7EE
Firmware version: 1.13
CPU frequency: 264 MHz
Memory size: 64 MB
Korina MAC address: 00:0C:42:04:AF:59
VIA1 MAC address: 00:0C:42:04:AF:5A
VIA2 MAC address: 00:0C:42:04:AF:5B
VIA3 MAC address: 00:0C:42:03:64:39
VIA4 MAC address: 00:0C:42:03:64:3A
VIA5 MAC address: 00:0C:42:03:64:3B
VIA6 MAC address: 00:0C:42:03:64:3C
VIA7 MAC address: 00:0C:42:03:64:3D
VIA8 MAC address: 00:0C:42:03:64:3E

But i only see 3 ethernets in mikrotik RouterOS.

I also tried with 48v / 0,4A power supply as i am currently using an 18v / 0,8A.

Where is the problem?

2

What does “/system resource pci print” say?

3

/system resource pci print

# DEVICE VENDOR NAME IRQ
0 00:06.0 unknown unknown (rev: 1) 0
1 00:03.0 VIA Technologies, Inc. VT6105 [Rhine-III] (rev:… 143
2 00:02.0 VIA Technologies, Inc. VT6105 [Rhine-III] (rev:… 142
3 00:00.0 Integrated Device Technol… IDT79RC32434 (rev: 0) 140

Thank you for your interest!

4

I’m sorry for inconvenience, but what does “/system resource pci print detail” say?

5

/system resource pci print detail

0 device=“00:06.0” name=“unknown (rev: 1)” vendor=“unknown”
category=“PCI bridge” vendor-id=“0x3388” device-id=“0x0031” irq=0

1 device=“00:03.0” name=“VT6105 [Rhine-III] (rev: 134)”
vendor=“VIA Technologies, Inc.” category=“Ethernet controller”
vendor-id=“0x1106” device-id=“0x3106” irq=143 memory=0x50000100-0x500001FF
io=0x18800100-0x188001FF

2 device=“00:02.0” name=“VT6105 [Rhine-III] (rev: 134)”
vendor=“VIA Technologies, Inc.” category=“Ethernet controller”
vendor-id=“0x1106” device-id=“0x3106” irq=142 memory=0x50000000-0x500000FF
io=0x18800000-0x188000FF

3 device=“00:00.0” name=“IDT79RC32434 (rev: 0)”
vendor=“Integrated Device Technology, Inc.”
category=“Non-VGA unclassified device” vendor-id=“0x111d”
device-id=“0x0000” irq=140 io=0x18800000-0x188000FF

6

please contact support as soon as you can

7

The problem was with the RB532A… i sent it for service and fixed!

Thanks!

8

Hello,

I recently bought used RB532r5 and got the same issue as in this post. I will give more details as soon as I got home, but I want to know is it possible to fix it now since RB532 is EOL.

Best Regards
diax78