SwOS version 1.13 released

[becs]

**What’s new in 1.13:

*) allow to disable SFP port;
) do not disable SFP port if loss of signal is detected, some SFP modules
do not report it correctly;
) make autonegotiation work better;
What’s new in 1.12:

*) fixed problem - SFP port stops after ethernet port cfg change (RB260 only);
*) change default vlan mode on RB260 to ‘optional’;
*) fixed problem - SNMP worked even when disabled;
*) fixed problem - SFP autonegotiation setting was not saved (RB260 only);
*) fixed uptime to be correct;
*) fixed RB260GSP poe-out to work correctly after downgrade & upgrade back;

What’s new in 1.11:

*) added support for RB260GSP;

What’s new in 1.10:

*) allow to disable/enable auto negotiation on SFP port on RB260;
*) fixed problem - hosts tab stopped working if 0:0:0:0:0:0 was learned on RB250;
*) enable transmit on SFP port only when module with signal is detected;
*) fixed problem - port lock & lock on first did not work on RB260;
*) fixed problem - port full duplex setting was set for wrong port on RB260;
*) fixed problem - broadcast correct uptime to it’s neighbors;
*) fixed problem - port egress rate did not limit traffic properly on RB260;
*) fixed problem - sometimes board did not reboot after upgrade;
*) added vlan-id to static host table;

http://www.mikrotik.com/download

This version fixes 1Gbit ethernet autonegotiation with Cisco 3550 and improves compatibility with SFP modules which do not have DDM.

[mpreissner]

Any plans to add RADIUS authentication instead of local username/password?

[docmarius]

Please update the wiki so the SwOS manual covers the PoE options in the “Link Tab” section for the RB260GSP.

[LynxChaus]

This version break SFP link status reporting over SNMP. Module present, loss of signal detected but SNMP reports IF-MIB::ifOperStatus.6 = up(1).

[honzam]

Mikrotik : Why no topic about 1.14?

No info about new version on email.

[TBK]

What’s new in 1.14:

*) fixed RB260GSP poe-out;

Source: http://download.mikrotik.com/swos/changelog.txt


For 1.15 it would be great if an option to disables the LEDs permanently or partially (in accordance with a timetable) was added.

[raflik]

@TBK

What’s new in 1.14:

*) fixed RB260GSP poe-out;

Source: http://download.mikrotik.com/swos/changelog.txt


For 1.15 it would be great if an option to disables the LEDs permanently or partially (in accordance with a timetable) was added.

and allow to change port name and add vlan name. Maybe add some log with information port down/up - date/time?

[honzam]

@raflik

@TBK

What’s new in 1.14:

*) fixed RB260GSP poe-out;

Source: http://download.mikrotik.com/swos/changelog.txt


For 1.15 it would be great if an option to disables the LEDs permanently or partially (in accordance with a timetable) was added.

and allow to change port name and add vlan name. Maybe add some log with information port down/up - date/time?

+1

[pepino]

@raflik

@TBK

What’s new in 1.14:
For 1.15 it would be great if an option to disables the LEDs permanently or partially (in accordance with a timetable) was added.

and allow to change port name and add vlan name. Maybe add some log with information port down/up - date/time?

…and serial number and firmware version available over snmp.