What’s new in 5.2 (2011-Apr-26 16:09):
*) fixed webfig;
*) console - fixed problem with supout file generation and export that
appeared in version 5.1, it was causing console to enter busy loop
on some boards;
*) ssh client - added source address and remote command options;
*) user manager - added /tool usermanager profile;
*) route - fixed problem with missing connected routes;
Hello
Plz explain more about:
“*) route - fixed problem with missing connected routes;”
There was a problem, that some connected routes could suddenly disappear. This is fixed.
When you disabled an IP address and enabled it, no connected routes were populating in the routing table.
Well after a long chat with my pal Rudy last night, I was somewhat encouraged to give 5.1 a bash.
This morning, it was on MT site, this afternoon, it was replaced by ROS5.2… So biting hard down on a stick I fired it up.
Now please, what is this, some new frequency!!! 2429 Mhz… I hope that is not a pre-amble of what is to come.
Come on MT, I am scared enough to try any further ROS systems since 3.3 and 4.16, give me some confidence back!!!
Does not support Alpha AWPCI085HU miniPCI 500mW (Atheros AR5414, 802.11 a/b/g) in the RouterOS 5.2 RB433UAH. Scan OK, connect log: “failed connect, on 2452, authentication timeout”. AP encrypted and unencrypted (R52H connect OK). RouterOS 4.3 works.
Mikrotik,
Thanks for the SSH command capability, I’ve been wanting this for awhile now.
However, like most things in RouterOS, I would like to see the ability to capture the commands output to fully use this feature.
Example:
:local resource [/system ssh address= command=“/system resource print as-value”]
<Parse $resource to get remote router’s resource>
Oh, and I guess another thing is maybe to have the ability to specify a password at the command line if we choose to. This way we can run SSH commands unattended. This would allow a script to run a command remotely on another router if we choose to.
Anyway, these are the two features I would like to see along with SSH command to be of much use to me.
Thanks.
File → Download does not appear to work on v5.2 Webfig.
RB450G just upgraded to ROS 5.2, strange values in Queue Tree, column PCQ Queues:
Queues with these values are RED-type not PCQ-type.
On RB433AH everthing is OK.
Regards,
graphs - not working, on RouterBoard 750G v. 5.2
Display only:
Traffic and system resource graphing
Did you remember to enable/allow graphs from the IP you checked from? 
It is not visible Russian font
Radio problems
Noise-97 sometimes in an operating time from for it interrupts communication
The similar occurs even indoors
this is why you can use keys to authenticate from routeros client and it will work in same manner as paswordless key authentication from any other ssh client.
you have to add key to ‘/user ssh-keys private’ private key on local router and ‘/user ssh-keys’ to add public key and off you go.
Use caution on upgrade to 5.1 or 5.2, I cannot recall which one did this, BUT*****************************
Somehow through the upgrade process the Virtual AP’s did not work, so I removed all of them. Had just he main AP which i called basement AP, whic I clearly recal setting up after the upgrade since I had to disable wireless package so that the 100 %CPU issue didnt come up, which I found to be when additional Virtual AP’s are added thag is when the cpu goes to 100% When adding a Virtual AP, the MAC address is 00:00:00:00:00 where before when there was no problem, the MAC would fill in automatically with the MAC of that wireless card.
Save time, if it is all 0’s it will set your board to 100% cpu, and all interfaces in list will not show up. ( yes a BUG) still in 5.2 verified, and drove 20 Km’s with note book to fix that board again.
But this is NOT why I am pissed.. I had 5.1 running with the main AP set to basement AP, where before I had the main ap and 2 virtual ap’s Ie My own Private AP, MainFloorAP and BasementAP.
Needless to say the basment and main were on seperate bridges, and my private ap was on my private bridge, even called PRIVATE. On the upgrade to 5.2 SOMEHOW that only AP that I set up, called basementAP SOMEHOW switched from the bridge I set it to, being Basment bridge, and after the upgrade it was on the Bridge called PRIVATE…
so, needless to say, that wasnt what I wanted, my tenants roaming my network, which has alot of sensitive data, and has full access to other networks.
MT Fix these issues, how can you put 5.2 as a stable version on the download page if its been released this same day?
Fix the Virtual AP issues.
And for anyone wantign to test it, set up 3 ap’s named " AirMatrix-SK " " BasementAP " and “MainFloorAP” put them on theier seperate bridges with 2 or 3 ehter ports, have DHCP on basement ap and main ap, but none on private bridge. is it because the names end with AP? I dont know, but it will put the board, in my case a 493, to 100% and then interfaces will not be listed. To fix, disable the wireless package, reboot, may require a site visit, some times it boots, sometimes it doesnt.
Grrrrrr
please send supout.rif to the support.
RB750, V5.2.
Cant see the stat of the “slave” interfases:
WAN - out interface
LAN - is the Master Port, all other slaves.
Is it Ok ?
Yes, switched traffic is not going though the CPU.
Nomis, please make 5.1 available on the web site again, for ROS, X86 and 100 series.. Rudy says its fine, but I wont install 5.2 to anymore clients having seen frequency 2429 appear.. (see above post)
Ps, what is this I read that NV2 doesnt work on X86, I am currently using NV2 on wrap2E, which is X86 based. (it seams to be working OK ( apart from usual dropouts similar to other RB variants))
v5.1 contains many problems. v5.2 works fine. I don’t know what rudy says.