v6 rc7 released

RouterOS General
1

What’s new in 6.0rc7 (2013-Jan-18 13:04):

*) dhcp relay - possibility to add relay agent information option;
*) lcd - options current-interface, time-interval and all-interface-mode
no longer get reset after reboot;
*) fix reboot in virtualized enviroment;
*) lcd - improve slideshow screen;
*) console - file print now shows file size as small number with suffix;
*) dhcp v4 - fix problem when sometimes client or server failed to send packets
most likely it happened on vlan interfaces;
*) ipv6 - added setting to disable forwarding;
*) added “/ip neighbor discovery settings” menu with “default=yes/no” setting;

2

No fix to vrf? (not tested)

3

I think that this version has been tested

4

Now on to RC8

5 
/interface print



ether1-wan-primary ether 1500 1526 00:0C:42:41:6A:85
ether2-lan ether 1500 1522 1522 00:0C:42:41:6A:86


/ip neighbor print



0 ether2… 192.168.2.1 00:0C:42:41:6A:86 MikroTik 6.0rc7 RB433UAH
1 ether1… 99.99.99.99 00:0C:42:41:6A:85 MikroTik 6.0rc7 RB433UAH

Why it show me itself, or this is normal ?

On demo2.mt.lv all is ok.
On demo.mt.lv is double.

6

I downloaded new version of Winbox.exe from router and saved it on my desktop (as I always do) and after running Winbox, files listed below were created on my desktop:
advtool.crc, advtool.dll, dhcp.crc, dhcp.dll, hotspot.crc, hotspot.dll, mpls.crc, mpls.dll, ppp.crc, ppp.dll, roteros.crc, roteros.dll, roting4.crc, roting4.dll, secure.crc, secure.dll, system.crc, system.dll, wlan4.crc, wlan4.dll.

After I delete these files, Winbox creates files on desktop every time I start it.

7

I think it is normal if the mikrotik is the only one doing discovery protocol on the interface.

If there are other devices participating in discover, I don’t see the current RouterOS device listed on the interface. It’s been that way from 5.x for me anyway.

8

I discovered that after upgrade from 5.18,5.20,5.22 to 6.0rc7
interfaces/bridges just dissapears. So far i’ve upgraded four x86 units
and three of them got up without bridges at all. Therefore Ip adresses
are binded to “unknown” interface. Mess…
First I thought that it was only 5.22>6,0rc7 path that introduces a problem.
But, few minutes ago I encountered the same situation upgrading 5.18>6.0rc7.

9

it is weekend wait for the official forum post on monday, otherwise this thread will be ignored. they have done a good job this time :slight_smile: please. patience!

10

After installing the problems started:

  1. Decreased the frequency to 100 MHz
  2. Constant rebooting and not revert back, if not to use RS232

RouterBOOT booter 3.02

RouterBoard 450G

CPU frequency: 100 MHz
Memory size: 256 MiB
NAND size: 512 MiB

RouterBOOT booter 3.02

RouterBoard 450G

CPU frequency: 680 MHz
Memory size: 256 MiB
NAND size: 512 MiB

Press any key within 2 seconds to enter setup..

loading kernel from nand… OK
setting up elf image… OK
jumping to kernel code
Starting…
Starting services…
MikroTik 6.0rc7
MikroTik Login: Oops[#1]:
Cpu 0
$ 0 : 00000000 00000001 00000000 fffffffe
$ 4 : cec3d500 00000000 00000000 c02d2410
$ 8 : 0000003c c02391d4 0000cc34 cd0acb40
$12 : cdd7f42c 00000003 ffffffff 000086dd
$16 : cdc8f540 cec3d500 00000000 00000000
$20 : c0391fcc 00000001 00000000 00000000
$24 : 0000000c 134f4c7a
$28 : cf6d0000 cf6d1c58 cec3d500 c029cc50
Hi : 00000064
Lo : 000006ca
epc : cf59ca68 udpv6_queue_rcv_skb+0x5c/0x77c [ipv6@0xcf580000]
Not tainted
ra : c029cc50 release_sock+0x94/0x108
Status: 1000d203 KERNEL EXL IE
Cause : 00800008
BadVA : 00000030
PrId : 00019374 (MIPS 24Kc)
Process net (pid: 219, threadinfo=cf6d0000, task=cf5fde30, tls=7766d770)
Stack : cdc8f180 cd25c050 cd25c050 00000000 cec3d500 cdc8f540 c0420000 c029cc50
000000a4 ffffffff cec3d70c cec3d70c 00000000 cec3d70c 00000000 cf6d1ee0
cdfafea0 00000000 00000074 cf59df00 0000007c c02deb00 cf6d1efc cf6d1d30
00000008 00000001 00000000 00000000 cf6d1cd8 cdfafea0 00000000 00000000
0000000c 00000000 00000000 00001104 00000000 ff020000 00000000 00000000
…
Call Trace:
[] udpv6_queue_rcv_skb+0x5c/0x77c [ipv6@0xcf580000]
[] release_sock+0x94/0x108
[] udpv6_sendmsg+0x80c/0x980 [ipv6@0xcf580000]
[] sock_sendmsg+0x84/0x9c
[] sys_sendto+0xcc/0x10c
[] stack_done+0x20/0x44

Code: 8e020048 2403fffe 00621024 <8c420030> 30420004 14400008 32420004 02202021 00002821
—[ end trace df72217082fc4575 ]—
Kernel panic - not syncing: Fatal exception in interrupt

panicSaver: dumping panic to flash
flash: erase f
flash: prg f
spi_program_sector 0000000f
Rebooting in 1 seconds..

RouterBOOT booter 3.02

RouterBoard 450G

CPU frequency: 680 MHz
Memory size: 256 MiB
NAND size: 512 MiB

Press any key within 2 seconds to enter setup..

loading kernel from nand… OK
setting up elf image… OK
jumping to kernel code
Starting…
Starting services…
MikroTik 6.0rc7
MikroTik Login: Oops[#1]:
Cpu 0
$ 0 : 00000000 00000001 00000000 fffffffe
$ 4 : ceca2fc0 00000000 00000000 c02d2410
$ 8 : 0000003c c02391d4 000037c2 cd6a7660
$12 : ffffffff 00000003 ffffffff 000086dd
$16 : cf7bf6c0 ceca2fc0 00000000 00000000
$20 : c0391fcc 00000001 00000000 00000000
$24 : 00000000 00000000
$28 : cf6d2000 cf6d3c58 ceca2fc0 c029cc50
Hi : 00000020
Lo : 69a36992
epc : cf59ca68 udpv6_queue_rcv_skb+0x5c/0x77c [ipv6@0xcf580000]
Not tainted
ra : c029cc50 release_sock+0x94/0x108
Status: 1000d203 KERNEL EXL IE
Cause : 00800008
BadVA : 00000030
PrId : 00019374 (MIPS 24Kc)
Process net (pid: 219, threadinfo=cf6d2000, task=cf5fa280, tls=770d7770)
Stack : cdfba3c0 cf7e9a50 cf7e9a50 00000000 ceca2fc0 cf7bf6c0 c0420000 c029cc50
0000009f ffffffff ceca31cc ceca31cc 00000000 ceca31cc 00000000 cf6d3ee0
cdfcd680 00000000 0000006f cf59df00 00000077 c02deb00 cf6d3efc cf6d3d30
00000008 00000001 00000000 00000000 cf6d3cd8 cdfcd680 00000000 00000000
00000004 00000000 00000000 00001104 00000000 ff020000 00000000 00000000
…
Call Trace:
[] udpv6_queue_rcv_skb+0x5c/0x77c [ipv6@0xcf580000]
[] release_sock+0x94/0x108
[] udpv6_sendmsg+0x80c/0x980 [ipv6@0xcf580000]
[] sock_sendmsg+0x84/0x9c
[] sys_sendto+0xcc/0x10c
[] stack_done+0x20/0x44

Code: 8e020048 2403fffe 00621024 <8c420030> 30420004 14400008 32420004 02202021 00002821
—[ end trace 14a0ee4ef2829e9f ]—
Kernel panic - not syncing: Fatal exception in interrupt

panicSaver: dumping panic to flash
flash: erase f
flash: prg f
spi_program_sector 0000000f
Rebooting in 1 seconds..

RouterBOOT booter 3.02

RouterBoard 450G

CPU frequency: 680 MHz
Memory size: 256 MiB
NAND size: 512 MiB

Press any key within 2 seconds to enter setup..

loading kernel from nand… OK
setting up elf image… OK
jumping to kernel code
Starting…
Starting services…
MikroTik 6.0rc7
MikroTik Login:

>

I had to return to rc6.
11

can mikrotik team add find & replace feature in winbox?

12

RB433UAH

RouterOS + enable MetaROUTER >>> random crash RouterOS

13

and routing marks don’t work… reverted to rc6 → all ok.

14

Had this back in RC5 at least. Using a 750. Had to manually go out and recycle the router.

15

we checked two systems, x86. they both upgraded fine from v5.18 and v5.22 and kept all their bridge configuration. could you send us your complete config to support? maybe some other problem caused this. supout.rif files from v5 and v6 would be appreciated

16

Upgraded some MIPSBE and PPC based routers with a few bridge interfaces and did encounter any issues. Perhaps this is just a x86 issue? Anyone else see this?

17

My bridges were fine after upgrading to rc7 but I am seeing lots of random reboots - think it has to do with KVM, sent support a mail

18

ipv6 - added setting to disable forwarding;

how exactly is working this feature, how can I get my IPv6 address on box? I set up ipv6/setting/forward: no , but how I can get my IPv6 address now?

19

What version of Windows are you using? What other software is running? Maybe some antivirus programs?

20

It’s funny, but I have just checked once again and it does not happen anymore. Did You fixed it telepathically? :wink:
I guess that Winbox couldn’t access some path and downloaded its files to current directory.
Anyway, everything is OK now, thank You. :slight_smile: