Hello. There is an RB1100AHx4 DudeEdition with boot problem. Here is a log without reset
Annapurna Labs stage 2: stage2_eth3_ram_loader v1.65.1
Executing next!
Annapurna Labs stage 2: stage2.5_loader v1.65.1
SPD I2C Address:00000050
Executing next!
-----------------------------------------------------
Stage 3 version: 1.65.1
Commit ID: e88c9c4
CVOS commit ID: d32367c
HAL commit ID: 8b8f7b5
Build date: May 20 2015 19:57:35
-----------------------------------------------------
EEPROM Revision ID = 37
Device ID = a314
Device Info: AL31400X-140
Loading DT to 00100000 (18676 bytes)...
Board config ID: alpine_db (AL-214)
Loading application to 00100000 (43880 bytes)...
Executing application...
RouterBOOT booter 6.43.16
RouterBOARD 1100Dx4
CPU frequency: 1400 MHz
Memory size: 1024 MiB
NAND size: 128 MiB
loading kernel... OK
setting up elf image... OK
jumping to kernel code
a log with a clamped reset
Annapurna Labs stage 2: stage2_eth3_ram_loader v1.65.1
Executing next!
Annapurna Labs stage 2: stage2.5_loader v1.65.1
SPD I2C Address:00000050
Executing next!
-----------------------------------------------------
Stage 3 version: 1.65.1
Commit ID: e88c9c4
CVOS commit ID: d32367c
HAL commit ID: 8b8f7b5
Build date: May 20 2015 19:57:35
-----------------------------------------------------
EEPROM Revision ID = 37
Device ID = a314
Device Info: AL31400X-140
Loading DT to 00100000 (18676 bytes)...
Board config ID: alpine_db (AL-214)
Loading application to 00100000 (43880 bytes)...
Executing application...
RouterBOOT backup booter 3.36.3
RouterBOARD 1100Dx4
CPU frequency: 1400 MHz
Memory size: 1024 MiB
NAND size: 128 MiB
RouterOS cleanup...
Reset for 30sec
Annapurna Labs stage 2: stage2_eth3_ram_loader v1.65.1
Executing next!
Annapurna Labs stage 2: stage2.5_loader v1.65.1
SPD I2C Address:00000050
Executing next!
-----------------------------------------------------
Stage 3 version: 1.65.1
Commit ID: e88c9c4
CVOS commit ID: d32367c
HAL commit ID: 8b8f7b5
Build date: May 20 2015 19:57:35
-----------------------------------------------------
EEPROM Revision ID = 37
Device ID = a314
Device Info: AL31400X-140
Loading DT to 00100000 (18676 bytes)...
Board config ID: alpine_db (AL-214)
Loading application to 00100000 (43880 bytes)...
Executing application...
RouterBOOT backup booter 3.36.3
RouterBOARD 1100Dx4
CPU frequency: 1400 MHz
Memory size: 1024 MiB
NAND size: 128 MiB
loading kernel... OK
setting up elf image... OK
jumping to kernel code
eFuse hashed modulues does not match the EEPROM hashed modulus
in 13-th port POE/BOOT with clamped reset for 30 sec leds start blinking but in Netinstall device do not appear , What addresses to register in the settings?
192,168,88,1 does not fit. Thank you
sorry for my english.