Hello ,

I have routerboard g450 with v5.1, i have following problem, when i try :
Terminal
-----------------
system routerboard> upgrage
Do you really want upgrade firmware?[y/n]
y
firmware upgraded succesfully, please reboot for changes take effect


After reboot - no effect!

does "/system routerboard print" actually show any new routerboot version?

please see attach.

still can't update RB433UAH ...
After the reboot routerboard without effect.

Hi, then try to upgrade.

HTH,

Hi,

Code: Select all

 /system routerboard settings 
set force-backup-booter=no

then try to upgrade.

HTH,

Good advice, the update is successful.

CPU frequency for the update to the 100 MHz and was followed by the:
USB flash drive is lost, the micro-sd OK, helped the interruption of power supply routerboard.

why can not I access webfig interface?

Webfig broke in v5.1 5.2 should be released to fix this bug.

Mikrotik, what changed in v5.1 webfig that broke it? Is there anywhere we might log this to let users know not to use v5.1?

v5.2 will be released tomorrow. Sorry about that webfig problem.

Hi,

Code: Select all

 /system routerboard settings 
set force-backup-booter=no

then try to upgrade.

HTH,

I followed your advice and I upgraded the firmware from 2.28 to 2.29.
But, with the new firmware, I can't log in winbox from MAC address (which I use by default). Actually I can connect only through IP address.
How can I resolve this problem?
Any suggestion?

yours,

RE: webfig problem

I'm not sure if this is the same error, but this breaks webfig in FF. It remains stuck at "loading".....

From firebug: Of course, Line 1 is the entire file....

yes, as stated many times before, we know about this, and v5.2 will be released tomorrow, with the fix for this. of course there are other fixes there too

@adi55
Check your settings in '/ip neighbor', maybe discovery is disabled on local interfaces.

HTH,

Incorrectly quality

Normis-
Can we test 5.2 or tomorrow to have any plan to change build? Directory Share Mikrotik. Thanks

v5.2 will be released tomorrow. Sorry about that webfig problem.

I keep checking back and this post still says "tomorrow".

Is the unit of measure an Earth day or Venus day?

radio r52Hn rb433

It is malfunction of the equipment or an program problem??

v5.2 will be released tomorrow.

Still waiting!

Everyone still waiting

still nothing

while testing 5.2 for release some more problems where found, so we are working on those and thus release of 5.2 is delayed.

demo2.mt.lv is on 5.2, if anyone wants to play with.at least from winbox, I know it is 5.2

My RB450 runs 100% cpu all the time with 5.1

open tool->profile and see what specifically causes this

I just ran into the 100% cpu issue. How it happened:

* Was logged into RB1100 w/ 5.1 via SSH.
* Was going to /ip neighbor discovery to check settings. In the middle of typing the command the SSH session became unresponsive.
* SSH'd in via another console, it authenticated immediately but the console took forever to display the MOTD (mikrotik logo in text). Never received an actual prompt
* Logged in via winbox, everything working fine, it shows 100% cpu. Even launching a terminal from within Winbox had the same issue- took forever to display MOTD, never gets to an actual shell.

I left it this way for about an hour, it never recovered. Rebooted it. Issue has not occured again yet. I will remain logged in via ssh to see if it reproduces. The device in question is barely doing any traffic and has a single IPSec tunnel:



Is there any way to manually kill connected users/shells? This may have cleared up the problem.

while testing 5.2 for release some more problems where found, so we are working on those and thus release of 5.2 is delayed.

Thank you for the update I would like to wait for upgrade v5.2 when it is fully ready, working, and stable.

v5.2 will be released tomorrow. Sorry about that webfig problem.

I still dun see 5.2

Does not support Alpha AWPCI085HU miniPCI 500mW (Atheros AR5414, 802.11 a b g) in the RouterOS 5.x RB433UAH. Scan OK, connect: "failed connect, on 2452, authentication timeout". AP encrypted and unencrypted (R52H connect OK). RouterOS 4.3 works.

v5.2 will be released tomorrow. Sorry about that webfig problem.

I still dun see 5.2

Tomorrow has come !
I will test the new 5.2 ASAP.

After upgrage firmware routerboard to 2.29, have problem this 5.2 release, i can not update this release. Routerboard 450g work only 8 volts, when use 24 volts all ports - shutdown, no signals.
How can i resolve my problem.