Hello,
I would like to setup my new mAP 2nD as a router with the following settings:
WAN - eth2 - DHCP - PoE on.
LAN - eth1 - 10.13.7.1 /24- DHCP on from 10.13.7.51 - 10.13.7.99
WLAN - SSID Mikrotik Passphrase 67j8h6G5tV also DHCP on.
I can not figure out how to set it up like the above.
Any help is appreciated!
Thanks.
Re: mAP 2nD Beginner Setup Help.
Ether2 is a power-out port. Why do you want to send the power to your ISP? Please clarify. Normally the setup is reversed. Ether1 is for your WAN and the Ether2 gives power to some kind of LAN device.
Re: mAP 2nD Beginner Setup Help.
Hello normis, thanks for your response.Ether2 is a power-out port. Why do you want to send the power to your ISP? Please clarify. Normally the setup is reversed. Ether1 is for your WAN and the Ether2 gives power to some kind of LAN device.
My WAN is actually another router/aerial that will be powered by ether2 PoE of this device, hence why I need to reverse the setup.
Re: mAP 2nD Beginner Setup Help.
You can reset the configuration of the unit, remove the defaults. Then connect with Winbox over MAC (because you won't have an IP on the device). Then configure IP addresses on both ports, DHCP server on Ether1, DHCP client (I guess?) on the Ether2 and any other settings that you will need.
Re: mAP 2nD Beginner Setup Help.
Thanks normis. Yes I can see what I need to do but don't seem to have any luck.You can reset the configuration of the unit, remove the defaults. Then connect with Winbox over MAC (because you won't have an IP on the device). Then configure IP addresses on both ports, DHCP server on Ether1, DHCP client (I guess?) on the Ether2 and any other settings that you will need.
I reset the mAP - I log on to MAC address using Winbox, then I clear config and then use terminal - after reading the Wiki here's what I have used so far:
Code: Select all
/interface wireless
set wlan1 band=2ghz-b/g/n country="united kingdom" disabled=no frequency=auto mode=ap-bridge ssid=MikroTik wds-mode=disabled wireless-protocol=802.11
/interface wireless security-profiles
set default mode=dynamic-keys authentication-types=wpa2-psk wpa2-pre-shared-key=67j8h6G5tV
/ip pool
add name=dhcppool ranges=10.7.13.51-10.13.7.99
/interface bridge
add name=bridge
/interface bridge port
add bridge=bridge interface=wlan1
add bridge=bridge interface=ether1
/ip address
add address=10.7.13.1/24 interface=bridge network=10.7.13.0
add address=192.168.88.1/24 interface=ether2 network=192.168.88.0
/ip dhcp-client
add dhcp-options=hostname,clientid disabled=no interface=ether2
/ip dhcp-server
add address-pool=dhcppool disabled=no interface=bridge name=dhcp
/ip dhcp-server network
add address=10.7.13.0/24 dns-server=8.8.8.8 gateway=10.7.13.1Any help is appreciated!
Re: mAP 2nD Beginner Setup Help.
Correct dhcp pool end ip address to 10.7.13.99
As I understand you will have dhcp client on Ether 2. So remove ip address from ether2 (192.168.88.1/24)
Make a masquerade for ether2
/ip firewall nat
add action=masquerade chain=srcnat out-interface=ether2
As I understand you will have dhcp client on Ether 2. So remove ip address from ether2 (192.168.88.1/24)
Make a masquerade for ether2
/ip firewall nat
add action=masquerade chain=srcnat out-interface=ether2
Re: mAP 2nD Beginner Setup Help.
Hello JB172, brilliant! That fixed it and now everything is working as I wanted.Correct dhcp pool end ip address to 10.7.13.99
As I understand you will have dhcp client on Ether 2. So remove ip address from ether2 (192.168.88.1/24)
Make a masquerade for ether2
/ip firewall nat
add action=masquerade chain=srcnat out-interface=ether2
Thanks normis and JB172 for your help.
Who is online
Users browsing this forum: No registered users and 101 guests