I'm facing a maybe simple problem but I can't find it.
I'd like to link several CRS226-24G-2S+ (CRS) together. But the transfer rates are quite bad. about 50 bps to 1200 bps up to 8-9 kbps.
I used to connect the second SFP+ port with the first of the following CRS.
CRS2 (SFP2<->SFP1) CRS3 (SFP2<->SFP1) CRS4 (SFP2<->SFP1) CRS5 (SFP2<->SFP1) CRS6
On each is one bridge which includes all ports of the CRS.
No VLan needed. Just a simple config to connect 5 devices together with acceptable transfer rates.
In order to exclude defective cabels and hardware I connected a CCR1036-8G-2S+ which plays the role of Capsman to the Lancom router and the server and a PC.
Btest from the PC to the server shows the same bad transfer rates as in the config above. Again changed all the cable, same result.
I'm sure bad config is the cause of all the mess, but where?
Thanks for any hint
Andreas
Config of CRS2
Code: Select all
/interface bridge
add admin-mac=4C:5E:0C:93:C6:18 auto-mac=no comment=\
"created from master port" name=bridge1 protocol-mode=none
/interface ethernet
set [ find default-name=ether1 ] name=ether1-master speed=100Mbps
set [ find default-name=ether2 ] speed=100Mbps
set [ find default-name=ether3 ] speed=100Mbps
set [ find default-name=ether4 ] speed=100Mbps
set [ find default-name=ether5 ] speed=100Mbps
set [ find default-name=ether6 ] speed=100Mbps
set [ find default-name=ether7 ] speed=100Mbps
set [ find default-name=ether8 ] speed=100Mbps
set [ find default-name=ether9 ] speed=100Mbps
set [ find default-name=ether10 ] speed=100Mbps
set [ find default-name=ether11 ] speed=100Mbps
set [ find default-name=ether12 ] speed=100Mbps
set [ find default-name=ether13 ] speed=100Mbps
set [ find default-name=ether14 ] speed=100Mbps
set [ find default-name=ether15 ] speed=100Mbps
set [ find default-name=ether16 ] speed=100Mbps
set [ find default-name=ether17 ] speed=100Mbps
set [ find default-name=ether18 ] speed=100Mbps
set [ find default-name=ether19 ] speed=100Mbps
set [ find default-name=ether20 ] speed=100Mbps
set [ find default-name=ether21 ] speed=100Mbps
set [ find default-name=ether22 ] speed=100Mbps
set [ find default-name=ether23 ] speed=100Mbps
set [ find default-name=ether24 ] speed=100Mbps
set [ find default-name=sfp-sfpplus1 ] advertise=\
10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full name=\
sfp1-G2352P1
set [ find default-name=sfpplus2 ] advertise=\
10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full name=\
sfp2-CRS3
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/interface bridge port
add bridge=bridge1 interface=ether2
add bridge=bridge1 interface=ether3
add bridge=bridge1 interface=ether4
add bridge=bridge1 interface=ether5
add bridge=bridge1 interface=ether6
add bridge=bridge1 interface=ether7
add bridge=bridge1 interface=ether8
add bridge=bridge1 interface=ether9
add bridge=bridge1 interface=ether10
add bridge=bridge1 interface=ether11
add bridge=bridge1 interface=ether12
add bridge=bridge1 interface=ether13
add bridge=bridge1 interface=ether14
add bridge=bridge1 interface=ether15
add bridge=bridge1 interface=ether16
add bridge=bridge1 interface=ether17
add bridge=bridge1 interface=ether18
add bridge=bridge1 interface=ether19
add bridge=bridge1 interface=ether20
add bridge=bridge1 interface=ether21
add bridge=bridge1 interface=ether22
add bridge=bridge1 interface=ether23
add bridge=bridge1 interface=ether24
add bridge=bridge1 interface=sfp1-G2352P1
add bridge=bridge1 interface=sfp2-CRS3
add bridge=bridge1 interface=ether1-master
/ip neighbor discovery-settings
set discover-interface-list=!dynamic
/ip address
add address=192.168.10.12/24 comment=defconf interface=bridge1 network=\
192.168.10.0
/ip ssh
set forwarding-enabled=remote
/lcd interface
add interface=bridge1
/lcd interface pages
set 1 interfaces=ether13
/system clock
set time-zone-name=Europe/Berlin
/system identity
set name=CRS2
/system leds
set 0 interface=sfp1-G2352P1
set 1 interface=sfp1-G2352P1
set 2 interface=sfp2-CRS3
set 3 interface=sfp2-CRS3
/system ntp client
set enabled=yes primary-ntp=192.168.10.11 secondary-ntp=192.168.10.1
/system upgrade upgrade-package-source
add address=192.168.10.16 user=admin
Code: Select all
/interface bridge
add admin-mac=4C:5E:0C:93:53:82 auto-mac=no comment=defconf name=bridge
/interface ethernet
set [ find default-name=sfp-sfpplus1 ] name=sfp1-CRS2
set [ find default-name=sfpplus2 ] name=sfp2-CRS4
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/user group
set full policy="local,telnet,ssh,ftp,reboot,read,write,policy,test,winbox,pas\
sword,web,sniff,sensitive,api,romon,dude,tikapp"
/interface bridge port
add bridge=bridge comment=defconf interface=ether1
add bridge=bridge comment=defconf interface=ether2
add bridge=bridge comment=defconf interface=ether3
add bridge=bridge comment=defconf interface=ether4
add bridge=bridge comment=defconf interface=ether5
add bridge=bridge comment=defconf interface=ether6
add bridge=bridge comment=defconf interface=ether7
add bridge=bridge comment=defconf interface=ether8
add bridge=bridge comment=defconf interface=ether9
add bridge=bridge comment=defconf interface=ether10
add bridge=bridge comment=defconf interface=ether11
add bridge=bridge comment=defconf interface=ether12
add bridge=bridge comment=defconf interface=ether13
add bridge=bridge comment=defconf interface=ether14
add bridge=bridge comment=defconf interface=ether15
add bridge=bridge comment=defconf interface=ether16
add bridge=bridge comment=defconf interface=ether17
add bridge=bridge comment=defconf interface=ether18
add bridge=bridge comment=defconf interface=ether19
add bridge=bridge comment=defconf interface=ether20
add bridge=bridge comment=defconf interface=ether21
add bridge=bridge comment=defconf interface=ether22
add bridge=bridge comment=defconf interface=ether23
add bridge=bridge comment=defconf interface=ether24
add bridge=bridge comment=defconf interface=sfp1-CRS2
add bridge=bridge comment=defconf interface=sfp2-CRS4
/ip neighbor discovery-settings
set discover-interface-list=!dynamic
/ip address
add address=192.168.10.13/24 comment=defconf interface=bridge network=\
192.168.10.0
/ip ssh
set forwarding-enabled=remote
/lcd interface pages
set 1 interfaces=ether13,ether14
/system clock
set time-zone-name=Europe/Berlin
/system identity
set name=CRS3
/system ntp client
set enabled=yes primary-ntp=192.168.10.11 secondary-ntp=192.168.10.1
/system upgrade upgrade-package-source
add address=192.168.10.16 user=admin
Code: Select all
/interface bridge
add admin-mac=4C:5E:0C:93:C5:14 auto-mac=no comment=defconf name=bridge
/interface ethernet
set [ find default-name=ether1 ] speed=100Mbps
set [ find default-name=ether2 ] speed=100Mbps
set [ find default-name=ether3 ] speed=100Mbps
set [ find default-name=ether4 ] speed=100Mbps
set [ find default-name=ether5 ] speed=100Mbps
set [ find default-name=ether6 ] speed=100Mbps
set [ find default-name=ether7 ] speed=100Mbps
set [ find default-name=ether8 ] speed=100Mbps
set [ find default-name=ether9 ] speed=100Mbps
set [ find default-name=ether10 ] speed=100Mbps
set [ find default-name=ether11 ] speed=100Mbps
set [ find default-name=ether12 ] speed=100Mbps
set [ find default-name=ether13 ] speed=100Mbps
set [ find default-name=ether14 ] speed=100Mbps
set [ find default-name=ether15 ] speed=100Mbps
set [ find default-name=ether16 ] speed=100Mbps
set [ find default-name=ether17 ] speed=100Mbps
set [ find default-name=ether18 ] speed=100Mbps
set [ find default-name=ether19 ] speed=100Mbps
set [ find default-name=ether20 ] speed=100Mbps
set [ find default-name=ether21 ] speed=100Mbps
set [ find default-name=ether22 ] speed=100Mbps
set [ find default-name=ether23 ] speed=100Mbps
set [ find default-name=ether24 ] speed=100Mbps
set [ find default-name=sfp-sfpplus1 ] advertise=\
10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full name=\
sfp1-CRS3
set [ find default-name=sfpplus2 ] advertise=\
10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full name=\
sfp2-CRS5
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/user group
set full policy="local,telnet,ssh,ftp,reboot,read,write,policy,test,winbox,pas\
sword,web,sniff,sensitive,api,romon,dude,tikapp"
/interface bridge port
add bridge=bridge comment=defconf interface=ether1
add bridge=bridge comment=defconf interface=ether2
add bridge=bridge comment=defconf interface=ether3
add bridge=bridge comment=defconf interface=ether4
add bridge=bridge comment=defconf interface=ether5
add bridge=bridge comment=defconf interface=ether6
add bridge=bridge comment=defconf interface=ether7
add bridge=bridge comment=defconf interface=ether8
add bridge=bridge comment=defconf interface=ether9
add bridge=bridge comment=defconf interface=ether10
add bridge=bridge comment=defconf interface=ether11
add bridge=bridge comment=defconf interface=ether12
add bridge=bridge comment=defconf interface=ether13
add bridge=bridge comment=defconf interface=ether14
add bridge=bridge comment=defconf interface=ether15
add bridge=bridge comment=defconf interface=ether16
add bridge=bridge comment=defconf interface=ether17
add bridge=bridge comment=defconf interface=ether18
add bridge=bridge comment=defconf interface=ether19
add bridge=bridge comment=defconf interface=ether20
add bridge=bridge comment=defconf interface=ether21
add bridge=bridge comment=defconf interface=ether22
add bridge=bridge comment=defconf interface=ether23
add bridge=bridge comment=defconf interface=ether24
add bridge=bridge comment=defconf interface=sfp1-CRS3
add bridge=bridge comment=defconf interface=sfp2-CRS5
/ip neighbor discovery-settings
set discover-interface-list=!dynamic
/ip address
add address=192.168.10.14/24 comment=defconf interface=bridge network=\
192.168.10.0
/ip ssh
set forwarding-enabled=remote
/system clock
set time-zone-name=Europe/Berlin
/system identity
set name=CRS4
/system ntp client
set enabled=yes primary-ntp=192.168.10.11 secondary-ntp=192.168.10.1
/system upgrade upgrade-package-source
add address=192.168.10.16 user=admin