IN SUMMARY your config bubble is about to be popped!!
(1) What are you doing here??
/interface wireguard peers
add allowed-address=192.168.88.0/24 interface=wireguard1 public-key=\
"1Of5xcGq53sXm6h8TKvkn7eGxNHEqom6fhBI8XDPg2I="
You have identified your own subnet as an allowed IP and on top of that have no entry for the client wireguard IP address or remote subnets if applicable?
Did you not read this..........
viewtopic.php?t=182340
(2) You have duplicate IP addresses assigned to the bridge
??????
/ip address
add address=192.168.88.1/24 comment=defconf
interface=bridge network=\
192.168.88.0
add address=192.168.100.1/24 interface=wireguard1 network=192.168.100.0
add address=10.10.10.254/8
interface=bridge network=10.0.0.0
(3) Good to see the added forward firewall rules (the last 3 here)............. so you need to get rid of this first rule..
add action=drop chain=forward comment=\
"defconf: drop all from WAN not DSTNATed" connection-nat-state=!dstnat \
connection-state=new in-interface-list=WAN
add action=accept chain=forward comment="allow internet traffic" \
in-interface-list=LAN out-interface-list=WAN
add action=accept chain=forward comment="allow port forwarding" \
connection-nat-state=dstnat
add action=drop chain=forward
(4) You might have some conflicts but not sure between the correctly formatted rule and the default rule the router comes with.
add action=src-nat chain=srcnat out-interface=pppoe-out1 to-addresses=\
XX.XX.XX.XX
add action=masquerade chain=srcnat comment="defconf: masquerade" \
ipsec-policy=out,none out-interface-list=WAN
Suggest moving the missing bit to the correct rule. so that it looks like this
add action=src-nat chain=srcnat out-interface=pppoe-out1 to-addresses=\
XX.XX.XX.XX
ipsec-policy=out,none
5. Your first dst-nat rule has the correct format and then you digress to the dynamic IP address format???
add action=dst-nat chain=dstnat dst-address=XX.XX.XX.XX dst-port=2000-65000 \
in-interface-list=WAN protocol=udp to-addresses=192.168.88.27 to-ports=\
2000-65000
add action=dst-nat chain=dstnat comment="FreePBX WebGUI" dst-port=8080 \
in-interface-list=WAN protocol=tcp to-addresses=192.168.88.27 to-ports=\
8080
Be consistent and use dst-address for all the dst-nat rules. Also if the to-ports is the same as dst-ports, it is not required to list them.
6. I dont understand the insanity of assigning ports 2-65000 to anything thats ridonkulous, what the heck for?
7. Duplicate rules..........
add action=dst-nat chain=dstnat dst-address=XX.XX.XX.XX dst-port=2000-65000 \
in-interface-list=WAN protocol=udp to-addresses=192.168.88.27 to-ports=\
2000-65000
add action=dst-nat chain=dstnat comment="FreePBX Media UDP" dst-port=\
2000-65001 in-interface-list=WAN protocol=udp to-addresses=192.168.88.27 \
to-ports=2000-65001
8. When you do such things you
BREAK port forwarding rules. Specifically that a port cannot be port forwarded more than ONCE on the inbound side.
Or stated otherwise HOW is the Router supposed to know where to send ports if it gets port 8080 for example, how does it know where to send it when 8080 is covered in a different rule.
9. Finally the other issue with 2-65000 ports is that NONE of your ipsec ports will be seen by the router as they will all be diverted to your dst-nat rules...........................
Whatever you think your are doing its wrong! Forwarding ports has to be done with the full context of what is going in the rest of the config.
Well as you can see I dont really know what I am doing lol
(1) What are you doing here??
/interface wireguard peers
add allowed-address=192.168.88.0/24 interface=wireguard1 public-key=\
"1Of5xcGq53sXm6h8TKvkn7eGxNHEqom6fhBI8XDPg2I="
You have identified your own subnet as an allowed IP and on top of that have no entry for the client wireguard IP address or remote subnets if applicable?
Did you not read this..........
viewtopic.php?t=182340
I will delete this, I am not trying to get wireguard working at the moment, although i will be in future
(2) You have duplicate IP addresses assigned to the bridge
??????
/ip address
add address=192.168.88.1/24 comment=defconf
interface=bridge network=\
192.168.88.0
add address=192.168.100.1/24 interface=wireguard1 network=192.168.100.0
add address=10.10.10.254/8
interface=bridge network=10.0.0.0
I may have done this to try get ether7-access working when the bridge was disabled or if i was locked out, not sure
6. I dont understand the insanity of assigning ports 2-65000 to anything thats ridonkulous, what the heck for?
I was having problems setting up FreePBX, like RTP not working, because it needed a certain port range. So I was not sure what port range it needed, so i just allowed all ports 2000 - 65000 to make sure it covered the required ports.
8. When you do such things you BREAK port forwarding rules. Specifically that a port cannot be port forwarded more than ONCE on the inbound side.
Or stated otherwise HOW is the Router supposed to know where to send ports if it gets port 8080 for example, how does it know where to send it when 8080 is covered in a different rule.
I have removed the duplicate rules. There are no overlapping rules now, as port 8080 is tcp and there is nothing overlapping tcp port 8080.
9. Finally the other issue with 2-65000 ports is that NONE of your ipsec ports will be seen by the router as they will all be diverted to your dst-nat rules...........................
Whatever you think your are doing its wrong! Forwarding ports has to be done with the full context of what is going in the rest of the config.
Changing to 10000 - 20000 instead of 2000 - 65000 stopped outgoing calls from working.
Also, I did the changes you said in this post but still my phone can't register when im on the private LAN and use the public IP. It works fine when I register using public IP when im external, or when i use the private LAN IP (192.168.88.27) when I am internal. So to register to the PBX, I need to use the internal IP when I am inside, and the external IP when I am outside. This would mean manually changing it each time I leave lol which is not great i guess
Can you see why it would not register from my code? Maybe i should try put it on a different subnet if the hairpin nat is not working
# sep/14/2022 17:14:25 by RouterOS 7.4
# software id = JCY8-AFLA
#
# model = RB2011iL
# serial number = E7DD0F73B4C5
/interface bridge
add admin-mac=DC:2C:6E:4C:59:6F auto-mac=no comment=defconf name=bridge
/interface ethernet
set [ find default-name=ether7 ] name=ether7-access
/interface pppoe-client
add add-default-route=yes disabled=no interface=ether1 name=pppoe-out1 \
use-peer-dns=yes user=eircom
/interface wireguard
add listen-port=13231 mtu=1420 name=wireguard1
/interface list
add comment=defconf name=WAN
add comment=defconf name=LAN
add comment=defconf name=MANAGE
add comment=defconf name=TRUSTED
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip pool
add name=dhcp ranges=192.168.88.10-192.168.88.254
add name=vpn ranges=192.168.89.2-192.168.89.255
/ip dhcp-server
add address-pool=dhcp interface=bridge name=defconf
/port
set 0 name=serial0
/ppp profile
set *FFFFFFFE dns-server=192.168.88.1 local-address=192.168.89.1 \
remote-address=vpn
/interface bridge port
add bridge=bridge comment=defconf interface=ether2
add bridge=bridge comment=defconf interface=ether3
add bridge=bridge comment=defconf interface=ether4
add bridge=bridge comment=defconf interface=ether5
add bridge=bridge comment=defconf interface=ether6
add bridge=bridge comment=defconf interface=ether8
add bridge=bridge comment=defconf interface=ether9
add bridge=bridge comment=defconf interface=ether10
/ip neighbor discovery-settings
set discover-interface-list=LAN
/interface l2tp-server server
set enabled=yes use-ipsec=yes
/interface list member
add comment=defconf interface=bridge list=LAN
add comment=defconf interface=ether1 list=WAN
add interface=pppoe-out1 list=WAN
add interface=ether7-access list=MANAGE
/interface pptp-server server
# PPTP connections are considered unsafe, it is suggested to use a more modern VPN protocol instead
set enabled=yes
/interface sstp-server server
set default-profile=default-encryption enabled=yes
/interface wireguard peers
add allowed-address=192.168.88.0/24 interface=wireguard1 public-key=\
"1Of5xcGq53sXm6h8TKvkn7eGxNHEqom6fhBI8XDPg2I="
/ip address
add address=192.168.88.1/24 comment=defconf interface=bridge network=\
192.168.88.0
add address=192.168.100.1/24 interface=wireguard1 network=192.168.100.0
/ip cloud
set ddns-enabled=yes
/ip dhcp-client
add comment=defconf disabled=yes interface=ether1
/ip dhcp-server lease
add address=192.168.88.232 mac-address=00:21:9B:3C:13:ED server=defconf
add address=192.168.88.231 client-id=1:b4:2e:99:16:e1:d0 comment=\
"Lorcan PC C1" mac-address=B4:2E:99:16:E1:D0 server=defconf
add address=192.168.88.218 client-id=1:0:1f:c1:1c:c9:80 mac-address=\
00:1F:C1:1C:C9:80 server=defconf
add address=192.168.88.216 client-id=1:0:1f:c1:1c:c4:20 mac-address=\
00:1F:C1:1C:C4:20 server=defconf
add address=192.168.88.215 client-id=1:0:1f:c1:1c:c4:1b mac-address=\
00:1F:C1:1C:C4:1B server=defconf
add address=192.168.88.214 client-id=1:0:1f:c1:1c:c4:1c mac-address=\
00:1F:C1:1C:C4:1C server=defconf
add address=192.168.88.213 client-id=1:0:1f:c1:1c:c4:8b mac-address=\
00:1F:C1:1C:C4:8B server=defconf
add address=192.168.88.212 client-id=1:0:1f:c1:1c:c4:91 mac-address=\
00:1F:C1:1C:C4:91 server=defconf
add address=192.168.88.211 client-id=1:0:1f:c1:1c:c9:7b mac-address=\
00:1F:C1:1C:C9:7B server=defconf
add address=192.168.88.209 client-id=1:38:22:e2:9f:d:91 mac-address=\
38:22:E2:9F:0D:91 server=defconf
add address=192.168.88.207 client-id=1:0:1f:c1:1c:c4:90 mac-address=\
00:1F:C1:1C:C4:90 server=defconf
add address=192.168.88.206 client-id=1:0:1f:c1:1c:c4:8d mac-address=\
00:1F:C1:1C:C4:8D server=defconf
add address=192.168.88.205 client-id=1:0:1f:c1:1c:c4:8f mac-address=\
00:1F:C1:1C:C4:8F server=defconf
add address=192.168.88.204 client-id=1:0:1f:c1:1c:c4:92 mac-address=\
00:1F:C1:1C:C4:92 server=defconf
add address=192.168.88.203 client-id=1:0:1f:c1:1c:c4:89 mac-address=\
00:1F:C1:1C:C4:89 server=defconf
add address=192.168.88.202 client-id=1:0:1f:c1:1c:c4:1e comment=\
"lorcan phone" mac-address=00:1F:C1:1C:C4:1E server=defconf
add address=192.168.88.201 client-id=1:0:1f:c1:1c:c4:22 mac-address=\
00:1F:C1:1C:C4:22 server=defconf
add address=192.168.88.200 client-id=1:0:1f:c1:1c:c4:8c mac-address=\
00:1F:C1:1C:C4:8C server=defconf
add address=192.168.88.199 client-id=1:0:1f:c1:1c:c4:1f mac-address=\
00:1F:C1:1C:C4:1F server=defconf
add address=192.168.88.198 client-id=1:0:1f:c1:1c:c4:23 mac-address=\
00:1F:C1:1C:C4:23 server=defconf
add address=192.168.88.196 client-id=1:90:9:d0:0:9:11 mac-address=\
90:09:D0:00:09:11 server=defconf
add address=192.168.88.194 client-id=1:0:11:32:ae:a2:7f mac-address=\
00:11:32:AE:A2:7F server=defconf
add address=192.168.88.165 client-id=1:0:1f:c1:1c:c4:8e mac-address=\
00:1F:C1:1C:C4:8E server=defconf
add address=192.168.88.163 client-id=1:34:f6:2d:89:e4:82 mac-address=\
34:F6:2D:89:E4:82 server=defconf
add address=192.168.88.154 client-id=1:0:1f:c1:1c:c4:8a mac-address=\
00:1F:C1:1C:C4:8A server=defconf
add address=192.168.88.92 client-id=1:b8:ec:a3:fd:1d:1f mac-address=\
B8:EC:A3:FD:1D:1F server=defconf
add address=192.168.88.91 client-id=1:b8:ec:a3:fd:1d:1c mac-address=\
B8:EC:A3:FD:1D:1C server=defconf
add address=192.168.88.192 client-id=1:e0:91:f5:c0:c:88 mac-address=\
E0:91:F5:C0:0C:88 server=defconf
add address=192.168.88.217 client-id=1:ec:8e:b5:d9:d7:82 comment="Joyce PC" \
mac-address=EC:8E:B5:D9:D7:82 server=defconf
add address=192.168.88.27 mac-address=6C:2B:59:E6:FB:01 server=defconf
add address=192.168.88.38 client-id=1:0:11:32:b8:2c:31 comment=\
"Backup server" mac-address=00:11:32:B8:2C:31 server=defconf
add address=192.168.88.48 client-id=1:48:2c:a0:79:49:22 comment=\
"lorcan phone" mac-address=48:2C:A0:79:49:22 server=defconf
/ip dhcp-server network
add address=192.168.88.0/24 comment=defconf dns-server=192.168.88.1 gateway=\
192.168.88.1
/ip dns
set allow-remote-requests=yes
/ip dns static
add address=192.168.88.1 comment=defconf name=router.lan
/ip firewall filter
add action=accept chain=input comment=\
"defconf: accept established,related,untracked" connection-state=\
established,related,untracked
add action=accept chain=input comment="allow IPsec NAT" dst-port=4500 \
protocol=udp
add action=accept chain=input comment="allow IKE" dst-port=500 protocol=udp
add action=accept chain=input comment="allow l2tp" dst-port=1701 protocol=udp
add action=accept chain=input comment="allow pptp" dst-port=1723 protocol=tcp
add action=accept chain=input comment="allow sstp" dst-port=443 protocol=tcp
add action=drop chain=input comment="defconf: drop invalid" connection-state=\
invalid
add action=accept chain=input comment="defconf: accept ICMP" protocol=icmp
add action=accept chain=input comment=\
"defconf: accept to local loopback (for CAPsMAN)" dst-address=127.0.0.1
add action=drop chain=input comment="defconf: drop all not coming from LAN" \
in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept in ipsec policy" \
ipsec-policy=in,ipsec
add action=accept chain=forward comment="defconf: accept out ipsec policy" \
ipsec-policy=out,ipsec
add action=fasttrack-connection chain=forward comment="defconf: fasttrack" \
connection-state=established,related hw-offload=yes
add action=accept chain=forward comment=\
"defconf: accept established,related, untracked" connection-state=\
established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" \
connection-state=invalid
add action=accept chain=forward comment="allow internet traffic" \
in-interface-list=LAN out-interface-list=WAN
add action=accept chain=forward comment="allow port forwarding" \
connection-nat-state=dstnat
add action=drop chain=forward
/ip firewall nat
add action=src-nat chain=srcnat ipsec-policy=out,none out-interface=\
pppoe-out1 to-addresses=XX.XX.XX.XX
add action=masquerade chain=srcnat dst-address=192.168.88.0/24 src-address=\
192.168.88.0/24
add action=src-nat chain=srcnat out-interface=ether1 to-addresses=\
XX.XX.XX.XX
add action=masquerade chain=srcnat comment="defconf: masquerade" \
ipsec-policy=out,none out-interface-list=WAN
add action=dst-nat chain=dstnat comment="FreePBX Media UDP" dst-address=\
XX.XX.XX.XX dst-port=2000-65001 in-interface-list=WAN protocol=udp \
to-addresses=192.168.88.27 to-ports=2000-65001
add action=dst-nat chain=dstnat comment="FreePBX WebGUI" dst-address=\
XX.XX.XX.XX dst-port=8080 in-interface-list=WAN protocol=tcp \
to-addresses=192.168.88.27 to-ports=8080
add action=dst-nat chain=dstnat comment="FreePBX LetsEncrypt" dst-address=\
XX.XX.XX.XX dst-port=80 in-interface-list=WAN protocol=tcp to-addresses=\
192.168.88.27 to-ports=80
add action=dst-nat chain=dstnat comment="FreePBX Tunnel TCP" dst-address=\
XX.XX.XX.XX dst-port=5090 in-interface-list=WAN protocol=tcp \
to-addresses=192.168.88.27 to-ports=5090
add action=dst-nat chain=dstnat comment="FreePBX SIP TCP" dst-address=\
XX.XX.XX.XX dst-port=5060 in-interface-list=WAN protocol=tcp \
to-addresses=192.168.88.27 to-ports=5060
add action=dst-nat chain=dstnat comment="FreePBX SIP TLS" dst-address=\
XX.XX.XX.XX dst-port=5061 in-interface-list=WAN protocol=tcp \
to-addresses=192.168.88.27 to-ports=5061
add action=dst-nat chain=dstnat dst-port=5500-5501 in-interface-list=WAN \
protocol=tcp to-addresses=192.168.88.194 to-ports=5500-5501
/ip firewall service-port
set sip sip-timeout=59w3d15h
/ipv6 firewall address-list
add address=::/128 comment="defconf: unspecified address" list=bad_ipv6
add address=::1/128 comment="defconf: lo" list=bad_ipv6
add address=fec0::/10 comment="defconf: site-local" list=bad_ipv6
add address=::ffff:0.0.0.0/96 comment="defconf: ipv4-mapped" list=bad_ipv6
add address=::/96 comment="defconf: ipv4 compat" list=bad_ipv6
add address=100::/64 comment="defconf: discard only " list=bad_ipv6
add address=2001:db8::/32 comment="defconf: documentation" list=bad_ipv6
add address=2001:10::/28 comment="defconf: ORCHID" list=bad_ipv6
add address=3ffe::/16 comment="defconf: 6bone" list=bad_ipv6
/ipv6 firewall filter
add action=accept chain=input comment=\
"defconf: accept established,related,untracked" connection-state=\
established,related,untracked
add action=drop chain=input comment="defconf: drop invalid" connection-state=\
invalid
add action=accept chain=input comment="defconf: accept ICMPv6" protocol=\
icmpv6
add action=accept chain=input comment="defconf: accept UDP traceroute" port=\
33434-33534 protocol=udp
add action=accept chain=input comment=\
"defconf: accept DHCPv6-Client prefix delegation." dst-port=546 protocol=\
udp src-address=fe80::/10
add action=accept chain=input comment="defconf: accept IKE" dst-port=500,4500 \
protocol=udp
add action=accept chain=input comment="defconf: accept ipsec AH" protocol=\
ipsec-ah
add action=accept chain=input comment="defconf: accept ipsec ESP" protocol=\
ipsec-esp
add action=accept chain=input comment=\
"defconf: accept all that matches ipsec policy" ipsec-policy=in,ipsec
add action=drop chain=input comment=\
"defconf: drop everything else not coming from LAN" in-interface-list=\
!LAN
add action=accept chain=forward comment=\
"defconf: accept established,related,untracked" connection-state=\
established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" \
connection-state=invalid
add action=drop chain=forward comment=\
"defconf: drop packets with bad src ipv6" src-address-list=bad_ipv6
add action=drop chain=forward comment=\
"defconf: drop packets with bad dst ipv6" dst-address-list=bad_ipv6
add action=drop chain=forward comment="defconf: rfc4890 drop hop-limit=1" \
hop-limit=equal:1 protocol=icmpv6
add action=accept chain=forward comment="defconf: accept ICMPv6" protocol=\
icmpv6
add action=accept chain=forward comment="defconf: accept HIP" protocol=139
add action=accept chain=forward comment="defconf: accept IKE" dst-port=\
500,4500 protocol=udp
add action=accept chain=forward comment="defconf: accept ipsec AH" protocol=\
ipsec-ah
add action=accept chain=forward comment="defconf: accept ipsec ESP" protocol=\
ipsec-esp
add action=accept chain=forward comment=\
"defconf: accept all that matches ipsec policy" ipsec-policy=in,ipsec
add action=drop chain=forward comment=\
"defconf: drop everything else not coming from LAN" in-interface-list=\
!LAN
/ppp secret
add name=vpn profile=default-encryption
/system clock
set time-zone-name=Europe/Dublin
/tool mac-server
set allowed-interface-list=LAN
/tool mac-server mac-winbox
set allowed-interface-list=LAN