Post your config. I have been able to successfully pass vpls traffic on my test bench with 7.1 between a few rb1100ahx4's I use for testing.
These are the last configs of the two RBs used for testing. They are connected directly with ethernet.
# feb/09/2022 14:25:54 by RouterOS 7.2rc3
# model = 1100AHx2
/interface bridge
add admin-mac=32:3E:39:11:B6:18 auto-mac=no name=loopback protocol-mode=none
/interface ethernet
set [ find default-name=ether10 ] l2mtu=9498 name=ether10_RB2011
set [ find default-name=ether1 ] name=ether12
set [ find default-name=ether2 ] l2mtu=9000 name=ether13_mgmt
/interface vpls
add arp=enabled cisco-static-id=10 disabled=no mac-address=02:A8:6C:37:29:04 mtu=1500 name=vpls1 peer=10.50.50.101 pw-control-word=disabled pw-l2mtu=1508 pw-type=raw-ethernet
/interface lte apn
set [ find default=yes ] ip-type=ipv4
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/port
set 0 name=serial0
set 1 name=serial1
/routing ospf instance
add name=default-v2 redistribute=connected,static router-id=10.50.50.100
/routing ospf area
add instance=default-v2 name=backbone-v2
/ip neighbor discovery-settings
set discover-interface-list=all
/ip settings
set max-neighbor-entries=8192
/ipv6 settings
set max-neighbor-entries=8192
/interface ovpn-server server
set auth=sha1,md5
/ip address
add address=10.50.50.100 interface=loopback network=10.50.50.100
add address=10.254.1.21/30 interface=ether10_RB2011 network=10.254.1.20
add address=10.254.1.202/30 interface=vpls1 network=10.254.1.200
/ip dhcp-client
add disabled=yes interface=ether13_mgmt
/ip dns
set servers=8.8.8.8
/ip service
set www-ssl certificate=root-cert disabled=no
/mpls interface
add disabled=no interface=all mpls-mtu=1600
/mpls ldp
add afi=ip disabled=no lsr-id=10.50.50.100 transport-addresses=10.50.50.100 vrf=main
/mpls ldp interface
add accept-dynamic-neighbors=yes disabled=no hello-interval=5s hold-time=15s interface=ether10_RB2011
/routing ospf interface-template
add area=backbone-v2 comment=2011 cost=10 interfaces=ether10_RB2011 networks=10.254.1.20/30 type=ptp
add area=backbone-v2 cost=10 interfaces=loopback networks=10.50.50.100/32
/system clock
set time-zone-name=Europe/Budapest
/system identity
set name="Test RB1100AHx2 v7"
/system ntp client
set enabled=yes
/system ntp client servers
add address=pool.ntp.org
/system package update
set channel=testing
/system routerboard settings
set auto-upgrade=yes
/tool romon
set enabled=yes
#
#
#
#-----------------
#
#
#
# feb/09/2022 14:23:25 by RouterOS 7.2rc3
# model = 2011UiAS
/interface bridge
add name=loopback protocol-mode=none
/interface ethernet
set [ find default-name=ether1 ] l2mtu=4074 name=ether1_RB1100
/interface vpls
add arp=enabled cisco-static-id=10 disabled=no mac-address=02:17:D7:9F:72:3E mtu=1500 name=vpls1 peer=10.50.50.100 pw-control-word=disabled pw-l2mtu=1508 pw-type=raw-ethernet
/interface lte apn
set [ find default=yes ] ip-type=ipv4
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/port
set 0 name=serial0
/routing ospf instance
add name=default-v2 redistribute=connected,static router-id=10.50.50.101
/routing ospf area
add instance=default-v2 name=backbone-v2
/ip settings
set max-neighbor-entries=8192
/ipv6 settings
set disable-ipv6=yes max-neighbor-entries=8192
/interface ovpn-server server
set auth=sha1,md5
/ip address
add address=10.254.1.22/30 interface=ether1_RB1100 network=10.254.1.20
add address=10.50.50.101 interface=loopback network=10.50.50.101
/ip dns
set servers=8.8.8.8
/mpls interface
add disabled=no interface=all mpls-mtu=1600
/mpls ldp
add afi=ip disabled=no lsr-id=10.50.50.101 transport-addresses=10.50.50.101 vrf=main
/mpls ldp interface
add accept-dynamic-neighbors=yes disabled=no hello-interval=5s hold-time=15s interface=ether1_RB1100
/routing ospf interface-template
add area=backbone-v2 auth-id=1 auth-key="" cost=10 interfaces=ether1_RB1100 networks=10.254.1.20/30 priority=1 type=ptp
add area=backbone-v2 interfaces=loopback networks=10.50.50.101/32 passive
/system clock
set time-zone-name=Europe/Budapest
/system identity
set name="Test RB2011 v7"
/system ntp client
set enabled=yes
/system ntp client servers
add address=162.159.200.1
/system package update
set channel=testing
/system routerboard settings
set auto-upgrade=yes
/tool romon
set enabled=yes
The problem is the same: VPLS tunnel shows "R", but they are not really working, there is no rx data, only tx.
I have already tested with three RBs, with the same result.
If anybody has a worcing config, please share with me, beacause I slowly rip my hair out
(just kidding...I'm bald
)
You do not have the required permissions to view the files attached to this post.