Page 1 of 1
2 x CSS326-24G-2S+RM
Posted: Wed Aug 23, 2017 4:00 pm
by SumiZA
Hi,
I have purchased 2 x CSS326-24G-2S+RM units with a SFP+ DAC 1M cable for uplink. Per my understanding, this should provide 10gb uplink between the 2 switches, however upon testing this was not achievable (only got 1gbps between the SFP ports whether or not i used auto negotiate) - is this feature supported between multiple CSS Devices? If it is a software bug, is there an estimated time before a fix? I am considering getting another 6 of these units to use for our main network in one of our offices and need this to be clarified before i go ahead.
Thank you in advance
Re: 2 x CSS326-24G-2S+RM
Posted: Wed Aug 23, 2017 4:06 pm
by pukkita
double check the ROS or SwOS version and firmware, from
SwOS changelog:
What's new in v2.4:
*) CSS106: fixed upgrade over PoE ports when PoE stopped working;
*) CRS326: fixed port in disabled VLAN mode to forward untagged packets;
What's new in v2.3:
*) fixed CRS317: make 10G links more stable;
*) fixed "Allow From VLAN" on untagged packets with correct default vlan id;
*) LACP: fixed unstable aggregate link problem when partner had short retransmit timer;
*) CSS326 & CRS317: made 1Gb fiber SFP module work with auto negotiation;
*) CSS106: do not VLAN tag RSTP packets;
What's new in v2.2:
*) fixed CSS326 & CRS317 switch MAC address;
*) fixed CRS317 lockup;
*) make CSS326 & CRS317 10G links more stable;
*) fixed CRS317 temperature reading;
*) fixed problem where big ACL, VLAN or static hosts lists kept only couple of first entries;
*) made "Save Backup" work on CSS106;
*) SNMP: report always 0 in IF-MIB:ifOutQLen;
*) CSS106: report correct speed for SFP port via SNMP;
What's new in v2.1:
*) added support for per port and ACL ingress rate limitation to CSS326 & CRS317;
*) added support for LACP in CSS326 & CRS317;
*) fixed CSS106 accessing over VLAN;
*) fixed CSS106 ACL rules that change VLANs;
*) added tx/rx rates per port to CSS106;
*) SNMP: added support for BRIDGE MIB;
*) SNMP: added support for GetBulkRequest;
Re: 2 x CSS326-24G-2S+RM
Posted: Wed Aug 23, 2017 4:37 pm
by SumiZA
double check the ROS or SwOS version and firmware, from
SwOS changelog:
What's new in v2.4:
*) CSS106: fixed upgrade over PoE ports when PoE stopped working;
*) CRS326: fixed port in disabled VLAN mode to forward untagged packets;
What's new in v2.3:
*) fixed CRS317: make 10G links more stable;
*) fixed "Allow From VLAN" on untagged packets with correct default vlan id;
*) LACP: fixed unstable aggregate link problem when partner had short retransmit timer;
*) CSS326 & CRS317: made 1Gb fiber SFP module work with auto negotiation;
*) CSS106: do not VLAN tag RSTP packets;
What's new in v2.2:
*) fixed CSS326 & CRS317 switch MAC address;
*) fixed CRS317 lockup;
*) make CSS326 & CRS317 10G links more stable;
*) fixed CRS317 temperature reading;
*) fixed problem where big ACL, VLAN or static hosts lists kept only couple of first entries;
*) made "Save Backup" work on CSS106;
*) SNMP: report always 0 in IF-MIB:ifOutQLen;
*) CSS106: report correct speed for SFP port via SNMP;
What's new in v2.1:
*) added support for per port and ACL ingress rate limitation to CSS326 & CRS317;
*) added support for LACP in CSS326 & CRS317;
*) fixed CSS106 accessing over VLAN;
*) fixed CSS106 ACL rules that change VLANs;
*) added tx/rx rates per port to CSS106;
*) SNMP: added support for BRIDGE MIB;
*) SNMP: added support for GetBulkRequest;
Thanks, however i am running version 2.4 on both CSS326 devices.
1Gbps works perfectly on sfp module, just not 10gbps and there is no option.
Re: 2 x CSS326-24G-2S+RM
Posted: Wed Aug 23, 2017 7:53 pm
by pukkita
I would directly write support in this case. BTW, There's a SwOS 2.5rc2 release candidate version, not sure if would help in your case.
Re: 2 x CSS326-24G-2S+RM
Posted: Thu Aug 24, 2017 5:02 pm
by SumiZA
I would directly write support in this case. BTW, There's a SwOS 2.5rc2 release candidate version, not sure if would help in your case.
Where can i get 2.5rc2 ? I cannot find any links for it under forum/download pages.
Re: 2 x CSS326-24G-2S+RM
Posted: Thu Aug 24, 2017 7:28 pm
by pukkita
Check updates from SwOS GUI
Re: 2 x CSS326-24G-2S+RM
Posted: Thu Aug 24, 2017 9:52 pm
by Alestrix
Hi,
Not sure whether this helps, but I have a DAC between my SFP+-equiped-NAS and CSS326 and the switch auto-negotiates the port to 10G according to the 'Link' tab. I didn't have the time yet to actually test the bandwidth, though.
Cheers,
Alex
Re: 2 x CSS326-24G-2S+RM
Posted: Tue Oct 17, 2017 9:50 pm
by ponury
Hi,
I'm having the same problem with my setup - 2 x CSS326-24G-2S+RM and SFP+ DAC 1M.
For some reasons I can't achieve 10G connection between those switches. Here is what I tried so far:
- different ports (SFP+ 1 and 2)
- SwOS 2.0/2/3/4/5/6
- configuration reset
Switches are strait from the box, without any additional configuration.
Have you found a solution for this problem?
Regards,
Maciej.
Re: 2 x CSS326-24G-2S+RM
Posted: Wed Oct 18, 2017 7:14 am
by Melody5781
I didn't see 2.5rc2 either. But I noticed there's version 2.6 for CSS326. Will that be helpful? This problem occured with other users as well. Did you guys call support from MikroTik?
Re: 2 x CSS326-24G-2S+RM
Posted: Wed Oct 18, 2017 9:38 am
by ponury
As I mentioned in my previous post I've checked firmwares 2.0/2.2/2.3/2.4/2.5 and 2.6
And I haven't contacted the support yet.
Re: 2 x CSS326-24G-2S+RM
Posted: Wed Oct 18, 2017 10:46 am
by skylark
Hi Ponury,
We improved DAC linking on CSS326-24G-2S+RM and there should not be any issues with SwOS 2.6. Have you tried some simple steps like disable/enable interfaces, power-cycle device, reinsert transceivers? Please give us more information how we could repeat this to see if there really is some issue or it's maybe HW fault.
Re: 2 x CSS326-24G-2S+RM
Posted: Wed Oct 18, 2017 1:28 pm
by ponury
Hi Arturs,
Thanks for joining this thread!
I've just checked disabling/enabling interfaces, reinserting transceivers and power-cycling both switches - still no 10G.
Maybe I'm wrong assuming that while there is a 10G connection there should be 10G text in the Speed column under the Link tab of the SwOS and the second led indicator under the SFP+ port should lit up?
Also, I've noticed that there is no option for 10G speed when I disable the Auto Negotiation feature on the SFP+ interface.
Re: 2 x CSS326-24G-2S+RM
Posted: Wed Oct 18, 2017 4:20 pm
by apophyth
Hello cheers,
same thing here, impossible to negotiate at 10Gbps with DAC cables with 2 units of CRS317-1G-16S+ with the new 2.6 firmware. Early, no problem with 2.5.
With RouterOS, no any kind of problem to negotiate at 10G.
Have a nice day
A.
Re: 2 x CSS326-24G-2S+RM
Posted: Fri Sep 18, 2020 5:28 pm
by Weev
Hello, I have to revive this thread as I'm facing the exact same issue here!
Switch is on the latest available firmware from the built in updater.
I can get a 1G link if I set negotiation to manual, however in manual I have no 10G option, and on auto negotiation I can't get a link.