Community discussions

MikroTik App
 
User avatar
Antixx
Member Candidate
Member Candidate
Topic Author
Posts: 100
Joined: Mon Jun 26, 2006 9:46 am

HELP FROM THIS PROBLEM

Tue Jan 02, 2007 12:38 am

Hi, I have been trying to route my dialup users which are on my CISCO AS5300 to the mk and do bandwidth manage but i have problem,
This is my config: :oops:

*AS5300 has two interface:
Ether0: primary 10.10.10.1 & sec 20.20.20.1 FastEther0: 192.168.2.1
IP POOL: 192.168.2.10-192.168.2.254 for Dialup Users
* MK has 3 interface:
ether0: 20.20.20.2
ether1: 192.168.3.1
ether2: 12.168.2.2
# WebCache (Squid Linux Box):
ether0: 20.20.20.3
# gateway Router wich connect to the internet:
Serial0: connected to the internet
FastEthernet0: Primary 20.20.20.3 sec 10.10.10.2
-----------------------------------------------------------
Ether0 and fastether0 on AS5300
Ether0 and Ether 2 on MK
Ether0 on web cache
FastEthernet0 on my Gateway router are connected to one HUB
---------------------------------------------------------------------
I use Router-Map to send source ip add 192.168.2.10.-254 which is my dialup users to the ether2 on MK and the use masq to nat dialupusers,
---------------------------------------
now when users connect to my AS5300 and get ip add in range 192.168.2.10-254 and can browse internet, Probelm start here when i monitor bandwith in interface section in MK i see!!!! i receive traffic from ether2 on MK which is nat valid ip and important thing is i see no traffic at ether0 which have valid ip address,,,
-----------------
in arp section on mk i see my webcache ip and mac add on ether1 which are physically in one network but have 2 diffrent range ip,
when i clear arp for ether1 which show webcache i show traffic coming from ether0,
i see webcache ip and mac in both ether0 and ether1,
------------------------
please help me what's happening!!!
i am very intrested to know what MK do? :shock: :shock:
Last edited by Antixx on Sat Jan 06, 2007 3:32 pm, edited 1 time in total.
 
User avatar
Antixx
Member Candidate
Member Candidate
Topic Author
Posts: 100
Joined: Mon Jun 26, 2006 9:46 am

Re: traffic coming from not valid interface (ip add)

Sat Jan 06, 2007 3:31 pm

Hi, I have been trying to route my dialup users which are on my CISCO AS5300 to the mk and do bandwidth manage but i have problem,
This is my config: :oops:

*AS5300 has two interface:
Ether0: primary 10.10.10.1 & sec 20.20.20.1 FastEther0: 192.168.2.1
IP POOL: 192.168.2.10-192.168.2.254 for Dialup Users
* MK has 3 interface:
ether0: 20.20.20.2
ether1: 192.168.3.1
ether2: 12.168.2.2
# WebCache (Squid Linux Box):
ether0: 20.20.20.3
# gateway Router wich connect to the internet:
Serial0: connected to the internet
FastEthernet0: Primary 20.20.20.3 sec 10.10.10.2
-----------------------------------------------------------
Ether0 and fastether0 on AS5300
Ether0 and Ether 2 on MK
Ether0 on web cache
FastEthernet0 on my Gateway router are connected to one HUB
---------------------------------------------------------------------
I use Router-Map to send source ip add 192.168.2.10.-254 which is my dialup users to the ether2 on MK and the use masq to nat dialupusers,
---------------------------------------
now when users connect to my AS5300 and get ip add in range 192.168.2.10-254 and can browse internet, Probelm start here when i monitor bandwith in interface section in MK i see!!!! i receive traffic from ether2 on MK which is nat valid ip and important thing is i see no traffic at ether0 which have valid ip address,,,
-----------------
in arp section on mk i see my webcache ip and mac add on ether1 which are physically in one network but have 2 diffrent range ip,
when i clear arp for ether1 which show webcache i show traffic coming from ether0,
i see webcache ip and mac in both ether0 and ether1,
------------------------
please help me what's happening!!!
i am very intrested to know what MK do? :shock: :shock:

Anybody can help me on this issue???? :cry:
 
User avatar
Antixx
Member Candidate
Member Candidate
Topic Author
Posts: 100
Joined: Mon Jun 26, 2006 9:46 am

Re: traffic coming from not valid interface (ip add)

Sat Jan 06, 2007 3:31 pm

Hi, I have been trying to route my dialup users which are on my CISCO AS5300 to the mk and do bandwidth manage but i have problem,
This is my config: :oops:

*AS5300 has two interface:
Ether0: primary 10.10.10.1 & sec 20.20.20.1 FastEther0: 192.168.2.1
IP POOL: 192.168.2.10-192.168.2.254 for Dialup Users
* MK has 3 interface:
ether0: 20.20.20.2
ether1: 192.168.3.1
ether2: 12.168.2.2
# WebCache (Squid Linux Box):
ether0: 20.20.20.3
# gateway Router wich connect to the internet:
Serial0: connected to the internet
FastEthernet0: Primary 20.20.20.3 sec 10.10.10.2
-----------------------------------------------------------
Ether0 and fastether0 on AS5300
Ether0 and Ether 2 on MK
Ether0 on web cache
FastEthernet0 on my Gateway router are connected to one HUB
---------------------------------------------------------------------
I use Router-Map to send source ip add 192.168.2.10.-254 which is my dialup users to the ether2 on MK and the use masq to nat dialupusers,
---------------------------------------
now when users connect to my AS5300 and get ip add in range 192.168.2.10-254 and can browse internet, Probelm start here when i monitor bandwith in interface section in MK i see!!!! i receive traffic from ether2 on MK which is nat valid ip and important thing is i see no traffic at ether0 which have valid ip address,,,
-----------------
in arp section on mk i see my webcache ip and mac add on ether1 which are physically in one network but have 2 diffrent range ip,
when i clear arp for ether1 which show webcache i show traffic coming from ether0,
i see webcache ip and mac in both ether0 and ether1,
------------------------
please help me what's happening!!!
i am very intrested to know what MK do? :shock: :shock:

Anybody can help me on this issue???? :cry:
 
User avatar
Antixx
Member Candidate
Member Candidate
Topic Author
Posts: 100
Joined: Mon Jun 26, 2006 9:46 am

Re: traffic coming from not valid interface (ip add)

Sat Jan 06, 2007 3:31 pm

Hi, I have been trying to route my dialup users which are on my CISCO AS5300 to the mk and do bandwidth manage but i have problem,
This is my config: :oops:

*AS5300 has two interface:
Ether0: primary 10.10.10.1 & sec 20.20.20.1 FastEther0: 192.168.2.1
IP POOL: 192.168.2.10-192.168.2.254 for Dialup Users
* MK has 3 interface:
ether0: 20.20.20.2
ether1: 192.168.3.1
ether2: 12.168.2.2
# WebCache (Squid Linux Box):
ether0: 20.20.20.3
# gateway Router wich connect to the internet:
Serial0: connected to the internet
FastEthernet0: Primary 20.20.20.3 sec 10.10.10.2
-----------------------------------------------------------
Ether0 and fastether0 on AS5300
Ether0 and Ether 2 on MK
Ether0 on web cache
FastEthernet0 on my Gateway router are connected to one HUB
---------------------------------------------------------------------
I use Router-Map to send source ip add 192.168.2.10.-254 which is my dialup users to the ether2 on MK and the use masq to nat dialupusers,
---------------------------------------
now when users connect to my AS5300 and get ip add in range 192.168.2.10-254 and can browse internet, Probelm start here when i monitor bandwith in interface section in MK i see!!!! i receive traffic from ether2 on MK which is nat valid ip and important thing is i see no traffic at ether0 which have valid ip address,,,
-----------------
in arp section on mk i see my webcache ip and mac add on ether1 which are physically in one network but have 2 diffrent range ip,
when i clear arp for ether1 which show webcache i show traffic coming from ether0,
i see webcache ip and mac in both ether0 and ether1,
------------------------
please help me what's happening!!!
i am very intrested to know what MK do? :shock: :shock:

Anybody can help me on this issue???? :cry:

Who is online

Users browsing this forum: No registered users and 77 guests