I have problems importing an RouterOS configuration from ROS 6.42.7. This config was running on a RB750GL and there I saw some strange errors so I wanted to reinstall the router from sratch.
At first I did a "export compact" to save the config. Then I used netinstall to reinstall the RouterOS 6.42.7 with default config.
After that I reset everything using "system reset-configuration no-defaults=yes". Now when I login again I wanted to import my backup config.
Executing "import test.rsc verbose=yes" fails at the last line:
Code: Select all
/interface bridge
add admin-mac=00:0C:42:C1:F9:9D auto-mac=no comment=\
"created from master port" name=bridge1 protocol-mode=none
/interface ethernet
set [ find default-name=ether1 ] name=ether1_trunk
set [ find default-name=ether2 ] name=ether2_trunk_out
set [ find default-name=ether3 ] name=ether3_Heimnetz
set [ find default-name=ether4 ] name=ether4_SmartHome
set [ find default-name=ether5 ] name=ether5_IPv6
/interface vlan
add interface=bridge1 loop-protect-disable-time=0s \
loop-protect-send-interval=00:00:01s name=vlan1_Heimnetz vlan-id=1
add interface=bridge1 loop-protect-disable-time=0s \
loop-protect-send-interval=00:00:01s name=vlan100_GuestWLAN vlan-id=100
add interface=bridge1 loop-protect-disable-time=0s \
loop-protect-send-interval=00:00:01s name=vlan200_FreyPV vlan-id=200
add interface=bridge1 loop-protect-disable-time=0s \
loop-protect-send-interval=00:00:01s name=vlan300_Test vlan-id=300
add interface=bridge1 loop-protect-disable-time=0s \
loop-protect-send-interval=00:00:01s name=vlan400_SmartHome vlan-id=400
add interface=bridge1 loop-protect-disable-time=0s \
loop-protect-send-interval=00:00:01s name=vlan500_IPv6 vlan-id=500
/interface ethernet switch port
set 0 default-vlan-id=0 vlan-header=add-if-missing vlan-mode=secure
set 1 default-vlan-id=1 vlan-header=always-strip vlan-mode=secure
set 2 default-vlan-id=400 vlan-header=always-strip vlan-mode=secure
set 3 default-vlan-id=500 vlan-header=always-strip vlan-mode=secure
set 4 default-vlan-id=0 vlan-header=add-if-missing vlan-mode=secure
set 5 default-vlan-id=0 vlan-header=add-if-missing vlan-mode=secure
/interface list
add name=winboxList
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip ipsec proposal
set [ find default=yes ] enc-algorithms=3des
/snmp community
set [ find default=yes ] addresses=0.0.0.0/0
/interface bridge port
add bridge=bridge1 interface=ether1_trunk # FAILING HERE
add bridge=bridge1 interface=vlan1_Heimnetz
add bridge=bridge1 interface=ether2_trunk_out
add bridge=bridge1 interface=ether3_Heimnetz
add bridge=bridge1 interface=ether4_SmartHome
add bridge=bridge1 interface=ether5_IPv6
....
Whats going on here? I mean I am importing the file I have just backuped?! I should under no circumstances fail to be imported
Now I am afraid I any of my dozen Mikrotiks failing, even with having the config
The execution of the import fails and I am disconnected by winbox and not able to reconnect at all. Only netinstall helps.