Community discussions

MUM Europe 2020
 
dormador
Member Candidate
Member Candidate
Topic Author
Posts: 107
Joined: Sat Mar 28, 2009 12:57 pm

problems with RADIUS and pppoe

Fri Oct 15, 2010 3:36 pm

Hi every one
I used radius and all points take authentication of a single box without any problems .
the problem, which happened to me there are as follows, I have a new network I have to merge three Internet lines where after merger i have an imbalance! The imbalance was due to the exit of the request of validated across the Line of Internet is not defined in main radius I mean, if if the request of validated went out of the pppoe1 be acceptance ..the request of the pppoe 2 or pppoe3 shows a letter there was no response from server I hope a solution to this problem.... so that it would be the exit of the request of the authentication from pppoe1 only

How can i do that !!
Last edited by dormador on Fri Oct 15, 2010 4:37 pm, edited 2 times in total.
 
User avatar
Ibersystems
Forum Guru
Forum Guru
Posts: 1684
Joined: Wed Apr 12, 2006 12:29 am
Location: Cabrils, Barcelona - Spain
Contact:

Re: ooooops a big problem for me need an immediate solution

Fri Oct 15, 2010 3:41 pm

Hi,

you can use mangle to mark all packets with destination your radius server IP, and mark all with a routeing mark to use only pppoe1
Martín
martinruiz at ibersystems.es
Experto en redes WiFi y enlaces WiFi.

Facebook: @Ibersystems
Twitter: @Ibersystems

Certified in Traffic Shaping, Wireless, Internetworking, Routing and User Management.
MTCTCE - MTCWE - MTCINE - MTCUME - MTCRE
 
dormador
Member Candidate
Member Candidate
Topic Author
Posts: 107
Joined: Sat Mar 28, 2009 12:57 pm

Re: ooooops a big problem for me need an immediate solution

Fri Oct 15, 2010 4:29 pm

thanks Ibersystems for rapid assistance

this is a mangle where is the point which will help in solving the problem .

 /ip firewall mangle> p
Flags: X - disabled, I - invalid, D - dynamic 
 0   chain=input action=mark-connection new-connection-mark=wan1 passthrough=yes 
     connection-state=new in-interface=pppoe-out1 

 1 I chain=input action=mark-connection new-connection-mark=wan2 passthrough=yes 
     connection-state=new in-interface=pppoe-out2 

 2 X chain=input action=mark-connection new-connection-mark=wan3 passthrough=yes 
     connection-state=new in-interface=pppoe-out3 

 3   chain=output action=mark-routing new-routing-mark=wan_1 passthrough=no 
     connection-mark=wan1 

 4   chain=output action=mark-routing new-routing-mark=wan_2 passthrough=no 
     connection-mark=wan2 

 5 X chain=output action=mark-routing new-routing-mark=wan_3 passthrough=no 
     connection-mark=wan3 

 6   chain=prerouting action=mark-connection new-connection-mark=wan1 
     passthrough=yes dst-address-type=!local in-interface=lan 
     per-connection-classifier=both-addresses-and-ports:3/0 

 7   chain=prerouting action=mark-connection new-connection-mark=wan2 
     passthrough=yes dst-address-type=!local in-interface=lan 
     per-connection-classifier=both-addresses-and-ports:3/1 

 8 X chain=prerouting action=mark-connection new-connection-mark=wan3 
     passthrough=yes dst-address-type=!local in-interface=lan 
     per-connection-classifier=both-addresses-and-ports:3/2 

 9   chain=prerouting action=mark-routing new-routing-mark=wan_1 passthrough=yes 
     in-interface=lan connection-mark=wan1 

10   chain=prerouting action=mark-routing new-routing-mark=wan_2 passthrough=yes 
     in-interface=lan connection-mark=wan2 

11 X chain=prerouting action=mark-routing new-routing-mark=wan_3 passthrough=yes 
     in-interface=lan connection-mark=wan3 
I have to disabled pppoe2&pppoe3 until the end of the imbalance
 
User avatar
Ibersystems
Forum Guru
Forum Guru
Posts: 1684
Joined: Wed Apr 12, 2006 12:29 am
Location: Cabrils, Barcelona - Spain
Contact:

Re: ooooops a big problem for me need an immediate solution

Fri Oct 15, 2010 4:47 pm

hi,

I think first you have to mark connection, then mark packet and later mark routing of these packets.
Martín
martinruiz at ibersystems.es
Experto en redes WiFi y enlaces WiFi.

Facebook: @Ibersystems
Twitter: @Ibersystems

Certified in Traffic Shaping, Wireless, Internetworking, Routing and User Management.
MTCTCE - MTCWE - MTCINE - MTCUME - MTCRE
 
dssmiktik
Forum Veteran
Forum Veteran
Posts: 732
Joined: Fri Aug 17, 2007 8:42 am

Re: ooooops a big problem for me need an immediate solution

Sun Oct 17, 2010 11:39 pm

dormador,
When you choose a topic, please choose something more descriptive. I just don't like clicking into the topics having no idea what they're about, when people say they need immediate solution.

update: topic has been changed
Last edited by dssmiktik on Sun Oct 31, 2010 6:11 am, edited 1 time in total.
Doug
 
dormador
Member Candidate
Member Candidate
Topic Author
Posts: 107
Joined: Sat Mar 28, 2009 12:57 pm

Re: problems with RADIUS and pppoe

Sat Oct 30, 2010 6:10 pm

Thanx everybody but until know the problem stell here !!!

Who is online

Users browsing this forum: MSN [Bot] and 78 guests