v6 rc5 released

Thu Dec 06, 2012 12:30 pm

What's new in 6.0rc5 (2012-Dec-05 15:22):

*) wireless - advanced rate selection is the only method supported;
*) ssh client - support keyboard-interactive authentication;
*) fix simple queue config upgrade;

http://www.mikrotik.com/download

honzam · Thu Dec 06, 2012 12:51 pm

RB111, RB112, RB113C, RBMinirouter devices are not supported in v6, please use v5
Never in the future?

Thu Dec 06, 2012 12:59 pm

RB111, RB112, RB113C, RBMinirouter devices are not supported in v6, please use v5
Never in the future?

too many features, too little RAM. those devices are quite old already, and new device of superior power costs as little as 39$

Raf · Thu Dec 06, 2012 1:19 pm

And too slow CPU.

w0lt · Thu Dec 06, 2012 1:35 pm

What's new in 6.0rc5 (2012-Dec-05 15:22):

*) wireless - advanced rate selection is the only method supported;
*) ssh client - support keyboard-interactive authentication;
*) fix simple queue config upgrade;

http://www.mikrotik.com/download

Normis,
Stable still downloads the 6.04 torrent...

stmx38 · Thu Dec 06, 2012 1:51 pm

And as always:
All stable files - http://www.mikrotik.com/download/routeros-ALL-6.0rc4.torrent

paoloaga · Thu Dec 06, 2012 2:18 pm

On 6.0rc5 I am not able to add PPPoE client interfaces. I tested it only on an RB951-2n. If needed I will send a supout.rif.

Thu Dec 06, 2012 2:25 pm

On 6.0rc5 I am not able to add PPPoE client interfaces. I tested it only on an RB951-2n. If needed I will send a supout.rif.

what is the error message? does the same command work on previous versions?

paoloaga · Thu Dec 06, 2012 2:31 pm

It's a standard configuration I apply to all the routers used as a CPE (around 1200 installations). It works with all previous releases.

Through CLI, if I add the interface, it just hangs. Through WinBOX it appears an error after a while, saying that it was not possible to add the PPPoE client interface.

It happens even just adding a PPPoE-Client, selecting any interface (example: ethernet 1) without any particular other setting.

Thu Dec 06, 2012 2:32 pm

It's a standard configuration I apply to all the router used as a CPE (around 1200 installations). It works with all previous releases.

Through CLI, if I add the interface, it just hangs. Through WinBOX it appears an error after a while, saying that it was not possible to add the PPPoE client interface.

It happens even just adding a PPPoE-Client, selecting any interface (example: ethernet 1) without any particular other setting.

looks like only hangs if you specify a password. can be added without a password. thanks for the report, will fix!

napismizpravu · Thu Dec 06, 2012 3:05 pm

again 6.0rc5
wireless package is not compatible RB433UAH + R52H, CM10

enable wireless packages > enable card R52H and CM10 (default config,reset) router KO! wireless packages CPU 97% KO RouterOS 6.0rc5
off -//- wireless packages router OK

5.21;5.22 error

downgrade 5.20

Thu Dec 06, 2012 3:07 pm

what is "KO"? how dead is it? Anything on serial console? Any autosupout.rif files? Those are standard cards, they work for other people. I doubt you would be the only one to notice.

napismizpravu · Thu Dec 06, 2012 3:23 pm

what is "KO"? how dead is it? Anything on serial console? Any autosupout.rif files? Those are standard cards, they work for other people. I doubt you would be the only one to notice.

CPU 100% useless, inefficient, broken RouterOS ... kernel KO?

Thu Dec 06, 2012 3:24 pm

what is "KO"? how dead is it? Anything on serial console? Any autosupout.rif files? Those are standard cards, they work for other people. I doubt you would be the only one to notice.
CPU 100% useless, inefficient, broken RouterOS ... kernel KO?

please answer my other questions

napismizpravu · Thu Dec 06, 2012 3:36 pm

what is "KO"? how dead is it? Anything on serial console? Any autosupout.rif files? Those are standard cards, they work for other people. I doubt you would be the only one to notice.
CPU 100% useless, inefficient, broken RouterOS ... kernel KO?

please answer my other questions

via winbox to get to settings, many settings disappeared (google translator)

honzam · Thu Dec 06, 2012 3:39 pm

show image
(vlož sem obrázek co ukazuje winbox po nahrání 6.0rc5) Jinak to asi nepochopí

napismizpravu · Thu Dec 06, 2012 3:48 pm

When you turn on wireless card > image

napismizpravu · Thu Dec 06, 2012 3:53 pm

show image
(vlož sem obrázek co ukazuje winbox po nahrání 6.0rc5) Jinak to asi nepochopí

no to je hrozný, když tu chtějí psát anglicky a nespokojí se s překladačem od Google

Tak mu kdyžtak napiš, že s vypnutým balíčkem wireless všechno funguje (kromě toho bezdrátu samozřejmě), a když se zapne, tak všechny karty jsou v default nastavení (a vypnutý) a po zapnutí kterýkoliv okamžitě je vidět na CPU zatížení wireless balíčku a celý routerboard je nepoužitelný. Ještě, že přes winbox jdou vypínat balíčky. ...dík

Thu Dec 06, 2012 3:54 pm

1. why do you have wireless package scheduled for disable?
2. why do you have some filters applied in wireless menu of winbox?

napismizpravu · Thu Dec 06, 2012 4:08 pm

1. why do you have wireless package scheduled for disable?
2. why do you have some filters applied in wireless menu of winbox?

1. enable R52H error > off-on wireless packeges (off R52H card) > test card CM10 (R52H off)
2. no filters enable (It showed the winbox)

honzam · Thu Dec 06, 2012 4:08 pm

He wrote:
With disabled wirelles package all works fine. When wirelles packages is enabled - then R52Hn and cm10 are in default settings. And when one of the card is enabled then cpu goes to 100% and routerboard is unusable

Stanislav Hrncir · Thu Dec 06, 2012 5:17 pm

Tady sa začíná rozjížďat multilingvistická debata

Oujé

wispwest · Thu Dec 06, 2012 5:32 pm

Really excited to test the new simple queues.

Had a RB/433GL running up a local tower to test on, with about 40 queues. Was running 6.0beta3. Upgraded to RC5.

Link to Mikrotik never came back, have to make site visit now, way to go Mikrotik!!

I'll post back if it just needed rebooted, or if the whole thing is bricked. This should be beta5, not RC5!

linek1980 · Thu Dec 06, 2012 5:41 pm

*) wireless - advanced rate selection is the only method supported;

the demo.mt.lv - yes. On my device - no. Two different versions of ROS-6.rc5?

wispwest · Thu Dec 06, 2012 6:18 pm

Really excited to test the new simple queues.

Had a RB/433GL running up a local tower to test on, with about 40 queues. Was running 6.0beta3. Upgraded to RC5.

Link to Mikrotik never came back, have to make site visit now, way to go Mikrotik!!

I'll post back if it just needed rebooted, or if the whole thing is bricked. This should be beta5, not RC5!

UPDATE:

- Reboot didn't fix
- Brought back to office and MAC-Winboxed into it, to find the interface names got changed! Therefor addresses assigned were now "unknown". Interfaces now say Eth3,Eth4,Eth5, when it should be Eth1, 2, and 3.

It's the same thing I see when a backup file is made, and restored onto another Mikrotik that has different ports. Everything gets all messed up. This was just a F/W upgrade though...

Thu Dec 06, 2012 6:36 pm

He wrote:
With disabled wirelles package all works fine. When wirelles packages is enabled - then R52Hn and cm10 are in default settings. And when one of the card is enabled then cpu goes to 100% and routerboard is unusable

on which board does it happen?
when the wireless cards are disabled the board works fine with wireless package enabled?
After which cards enable the board goes to 100% CPU?

jcem · Thu Dec 06, 2012 6:45 pm

wispwest!

what was your previous version before upgrade? I had simular problem when upgrading from pre ROS5.20

run command
/system check-installation

and see if you get any file errors - i did and had to do netinstall

could be that you had errors before upgrade, therefore your backup is
corrupted. Compare size of file with an older backup.

Check log for error when doing system backup

I had one installation going bad when upgrading from 5.20
to 5.22on an RB800 with userman. I got file
error(/system check-installation), error in log
when backup, all packages where not shown.
Wireless package was missing, but wireless still worked.
Had to netinstall and use an older backup file

On successful installations - I have fould no errors with ROS6.0RC5

RGDS

napismizpravu · Thu Dec 06, 2012 7:06 pm

He wrote:
With disabled wirelles package all works fine. When wirelles packages is enabled - then R52Hn and cm10 are in default settings. And when one of the card is enabled then cpu goes to 100% and routerboard is unusable
on which board does it happen?
when the wireless cards are disabled the board works fine with wireless package enabled?
After which cards enable the board goes to 100% CPU?

...reboot-wireless packages enable (off all card) router OK

write http://forum.mikrotik.com/viewtopic.php ... 63#p344963

tron · Thu Dec 06, 2012 7:13 pm

Zdravím Čechy a Slováky

(Greetings to Czechs and Slovaks)

Before update with RoS v5.22 -> 6to4 tunnel worked great - ping to IPv6 gateway was OK.

ros522.png

After update to RoS v6.05rc -> 6to4 tunnel didn't work. Gateway was unreachable. Nothing helped (re-setting interface, deleting/adding IPs, deleting/adding route...)

ros605rc.png

I downgraded back to v5.22 and it is working again.

wispwest · Thu Dec 06, 2012 7:19 pm

wispwest!

what was your previous version before upgrade? I had simular problem when upgrading from pre ROS5.20

run command
/system check-installation

and see if you get any file errors - i did and had to do netinstall

could be that you had errors before upgrade, therefore your backup is
corrupted. Compare size of file with an older backup.

Check log for error when doing system backup

I had one installation going bad when upgrading from 5.20
to 5.22on an RB800 with userman. I got file
error(/system check-installation), error in log
when backup, all packages where not shown.
Wireless package was missing, but wireless still worked.
Had to netinstall and use an older backup file

On successful installations - I have fould no errors with ROS6.0RC5

RGDS

I figured I would upgrade everything to 5.22 first, but this particular one already had 6.0beta3, so I just upgraded it from that one...

onnoossendrijver · Fri Dec 07, 2012 12:45 am

I'm still not able to install RouterOS 6rc5 on a USB stick.

NetworkPro · Fri Dec 07, 2012 7:18 am

I have decent experience with the recent RC versions, Thank you MikroTik guys !!!

On two mipsbe I put the package from 5th December from the development page, it has RouterBOOT 3.02, if you could consult with your colleagues and let us know if we can install it on the router OR wait for the next build and install the RouterBOOT from there ?

Thanks.

Fri Dec 07, 2012 7:45 am

RouterBOOT 3.02 should also be included in the public release of RC5. It is good to install.

blingblouw · Fri Dec 07, 2012 1:05 pm

running on x86.

Cannot stop a kvm

when i stop it it just says stopping but never actually stops

Edit:

Also, when a reboot happens the tap adapters are NOT removed. and I get DUP responses when trying to ping VM

Fri Dec 07, 2012 1:40 pm

set vnc display id and connect and look at output.
Then do /kvm shut-down <kvm-name>

Fri Dec 07, 2012 1:43 pm

I'm still not able to install RouterOS 6rc5 on a USB stick.

clarify what process you used? works with Netinstall to USB

blingblouw · Fri Dec 07, 2012 1:53 pm

set vnc display id and connect and look at output.
Then do /kvm shut-down <kvm-name>

I did this, nothing happens the VM still continues to work. Only shutsdown if I power the VM down (in the vm go shutdown)

napismizpravu · Fri Dec 07, 2012 2:46 pm

RB433UAH install number three
update 5.20 > 6.0rc5 > wireless packages CPU 100% ... cannot turn off wireless packages!, reset ...> KO! RouterOS
serial cabel > images
netinstal 6.0rc5 all packages > Kernel panic - not syncing: Attemped to kill init!
netinstall 6.0rc5 combine packages > Kernel panic....
netinstal 5.22 > install OK (bad sector 0,2% previously 0%)
winbox update 5.22 > 6.0rc5 > put the new wireless card > enable OK> restore configurations 5.22 >reboot> enable card CPU 100% wireless packages
netinstall 5.22>6.0rc5... configuration import compact all IP, IPv6, queues,...

Batman directory Comix RouterOS

Batmani, čerti a ještě to chce supermany, princezničky a bude routerboard jak z pohádky

Fri Dec 07, 2012 2:49 pm

your wireless card is probably damaged. try to install some other card. in certain situations, enabling a defective card will result in this situation.

Fri Dec 07, 2012 3:04 pm

set vnc display id and connect and look at output.
Then do /kvm shut-down <kvm-name>
I did this, nothing happens the VM still continues to work. Only shutsdown if I power the VM down (in the vm go shutdown)

Tested all shutdown, reboot, start etc. Works fine if guest is RouterOS. What OS is installed on your guest?

blingblouw · Fri Dec 07, 2012 3:10 pm

Fedora 15. Runs fine on all other versions fo ROS. (5.11 - 5.20)

Fri Dec 07, 2012 3:15 pm

Fedora 15. Runs fine on all other versions fo ROS. (5.11 - 5.20)

KVM host sends ACPI event to the guest. Try to check if your fedora accepts them.

napismizpravu · Fri Dec 07, 2012 3:18 pm

your wireless card is probably damaged. try to install some other card. in certain situations, enabling a defective card will result in this situation.

the cards work ...5.22 and now there are again 6.0rc5 work (no import config wireless 5.22)

Fri Dec 07, 2012 3:19 pm

your wireless card is probably damaged. try to install some other card. in certain situations, enabling a defective card will result in this situation.
the cards work ...5.22 and now there are again 6.0rc5 work (no import config wireless 5.22)

Sorry, language barrier. The card works now in rc5?

napismizpravu · Fri Dec 07, 2012 3:22 pm

your wireless card is probably damaged. try to install some other card. in certain situations, enabling a defective card will result in this situation.
the cards work ...5.22 and now there are again 6.0rc5 work (no import config wireless 5.22)
Sorry, language barrier. The card works now in rc5?

yes

Fri Dec 07, 2012 3:28 pm

how did you fix it?

onnoossendrijver · Fri Dec 07, 2012 4:07 pm

I'm still not able to install RouterOS 6rc5 on a USB stick.
clarify what process you used? works with Netinstall to USB

I use netinstall to install the routeros npk to usb stick.
Then I place the USB stick in the x86 machine where I want to run RouterOS, the following happens:

Welcome to MikroTik Router Software hard disk installation
Press Ctrl-Alt-Delete to abort

Loading drivers
Looking for harddrives.......................

FATAL ERROR: No hard disk found
Press ENTER to reboot

On RouterOS 5.x and routeros 6betaX this works perfectly, but not on routerOS 6rcX.
Tried on Intel DN2800MT and Intel D945GCLF2 motherboards (both have an Atom CPU)

crhylove · Fri Dec 07, 2012 8:23 pm

I had Hide Passwords checked and it was still showing my password. Not that it mattered at the moment, my boss knows my password. This is a potentially big deal though in some environments!

crhylove · Fri Dec 07, 2012 8:33 pm

Another Bug:

In IP > Hotspot > Walled Garden IP Entry

adding a url like securedserver.isp.net doesn't work, I get the error "Error in Dst. Address - ip address expected!"

napismizpravu · Fri Dec 07, 2012 8:55 pm

proxy random error "DNS resolving failed" (5x IP DNS servers, ISP1, ISP2, 2x Google IPv4 + IPv6)
mangle Layer7 Protokols

(5.22 better)

edit: uptime 6.0rc5 1d (5.22 1-max3d)... proxy DNS good (remove Web Proxy Access rule double clone all...the first import /IP was not successful terminal)

crhylove · Fri Dec 07, 2012 10:06 pm

Drag and drop functionality is also broken in Winbox. Trying to copy an html file into the hotspot directory. Had to right click copy, then select the past icon at the top of the File List to make it work.

hci · Sat Dec 08, 2012 12:01 am

Attempted to upgrade a RouterBOARD 951-2n for rc4 to rc5. Appears to be bricked. Solid PWR and ACT lights. Nothing else lights up. Any possible fixes besides RMA?

Chupaka · Sat Dec 08, 2012 2:34 am

Upgraded my semi-test x86 Intel router (with two 82576 + one 82574L NICs if it matters) from 5.22 to 6.0rc5 - no networking, any /interface print command ended in timeout + supout suggestion. I tried to make supout, but when NetInstalling v5, I checked 'Keep old configuration' - and as a result saw absolutely empty config with all files (including backups, f*ck!!!11oneone) erased, so I don't know how to extract supout from that router

p.s. in WinBox, one can change supout file name - how to do that in Terminal? "/system sup-output" doesn't have any parameters...

Sat Dec 08, 2012 10:41 am

Attempted to upgrade a RouterBOARD 951-2n for rc4 to rc5. Appears to be bricked. Solid PWR and ACT lights. Nothing else lights up. Any possible fixes besides RMA?

power it with pushed button, this will load secondary bootloader and run netinstall mode

Sat Dec 08, 2012 10:42 am

Upgraded my semi-test x86 Intel router (with two 82576 + one 82574L NICs if it matters) from 5.22 to 6.0rc5 - no networking, any /interface print command ended in timeout + supout suggestion. I tried to make supout, but when NetInstalling v5, I checked 'Keep old configuration' - and as a result saw absolutely empty config with all files (including backups, f*ck!!!11oneone) erased, so I don't know how to extract supout from that router

p.s. in WinBox, one can change supout file name - how to do that in Terminal? "/system sup-output" doesn't have any parameters...

I don't understand - did you manage to make the file or not? Try to send to support if you have anything

Vkins · Sat Dec 08, 2012 3:57 pm

<removed>

After flashing it again it worked properly. No idea what went wrong the first time.

Would still love to see a more...versatile implementation of UPnP along with NAT-PMP.

ddejager · Sat Dec 08, 2012 11:42 pm

I'm using a RB2011UAS-2HnD. I upgraded from v6rc2. No problems encountered with normal routing or wireless useage.

I decided to try to use external USB storage. I've tried with two different flash storaged devices, both formated in fat format. One device is a Cruzer, Micro 2GB. The other device is a SD-USB adapter with a 512 MB SD card. Both devices work fine when plugged into my Windows 7 computer. They also work if plugged into my Android phone using a Micro USB cable. When used on either the computer or phone, the LED on the device is either on all the time or flashing (depending on the USB flash device.)

If I use the exact same cable to plug either device into the router, the active LED on the device flashes very briefly and then nothing happens and the storage is not visible on the router. It is almost acting like it is not getting sufficient power from the router, but either device uses only a very small amount of power. Windows reports the SD-USB adapter as using 100 mA and reports the Cruzer as using 200 mA.

Why won't either device work with the RB? (I've not tested the USB storage on any prior software release on this device.)

Edit: neither device shows up in the list of stores. (no USB store is listed, only the system store)

Edit2: Figured out that I needed to reboot the router before the USB storage will appear and can then be formatted.

samotoka · Sat Dec 08, 2012 11:54 pm

Did you format the usb like that

ditonet · Sat Dec 08, 2012 11:56 pm

Format your USB drive using RouterOS built-in format tool.
Run Winbox, then 'System/Stores/Disks', select USB device and click 'Format Drive'.
RouterOS uses its own file system, not compatible with FAT

.
http://wiki.mikrotik.com/wiki/Manual:St ... commands_2

HTH,

edit: Samotoka was faster than me

samotoka · Sat Dec 08, 2012 11:58 pm

pic is better for the newbie

ddejager · Sun Dec 09, 2012 12:03 am

Format your USB drive using RouterOS built-in format tool.
Run Winbox, then 'System/Stores/Disks', select USB device and click 'Format Drive'.
RouterOS uses its own file system, not compatible with FAT .
http://wiki.mikrotik.com/wiki/Manual:St ... commands_2

HTH,

edit: Samotoka was faster than me

Thanks!

ddejager · Sun Dec 09, 2012 12:08 am

You answered my questions about USB storage so quickly...I have another question.

Again I have a RB2011UAS-2HnD board using v6rc5. I cannot get the "new" cable diagnostics to work as advertised. When I run the diagnostic for any ethernet port I get "status" and "auto-negotiation" reported back, but nothing about "cable-pairs". I've read in other postings that this only works on 5 of the 10 ports on this router (I forget if it was the gigabit or 100 mbit ports), but I cannot get it to work on any ports. I'm trying on ports that have no-link with various length cables plugged in.

Any suggestions?

ddejager · Sun Dec 09, 2012 12:16 am

Format your USB drive using RouterOS built-in format tool.
Run Winbox, then 'System/Stores/Disks', select USB device and click 'Format Drive'.
RouterOS uses its own file system, not compatible with FAT .
http://wiki.mikrotik.com/wiki/Manual:St ... commands_2

HTH,

edit: Samotoka was faster than me
Thanks!

I think I thanked you too quickly. The devices do not show up in the /store print list. That is, no USB storage is shown as in the image by samotoka, so it is not available for formatting.

ditonet · Sun Dec 09, 2012 12:20 am

Check USB port mode settings:
http://wiki.mikrotik.com/wiki/Manual:US ... _port_mode

HTH,

ddejager · Sun Dec 09, 2012 12:30 am

Format your USB drive using RouterOS built-in format tool.
Run Winbox, then 'System/Stores/Disks', select USB device and click 'Format Drive'.
RouterOS uses its own file system, not compatible with FAT .
http://wiki.mikrotik.com/wiki/Manual:St ... commands_2

HTH,

edit: Samotoka was faster than me
Thanks!
I think I thanked you too quickly. The devices do not show up in the /store print list. That is, no USB storage is shown as in the image by samotoka, so it is not available for formatting.

OK. I figured it out. I noticed in the wiki doc a notation that the router needs to be rebooted after installing the USB storage. I rebooted and it now shows up as a USB store and I can format it. Now to use it.

napismizpravu · Sun Dec 09, 2012 9:09 pm

curiosity RB433UAH max CPU 118%

6.0rc5 uptime currently 2d (5.22 max uptime 1-3d)

kosztyua · Sun Dec 09, 2012 10:03 pm

I just spent 8 hours yesterday trying to install v6rc5 x86. I usually install routeros systems remotely, either through kvm or ipmi and so far I had no trouble with it. But not this time, when trying to install from virtual cd the installer says no cd; when booting to windows and using netinstall to install local drive, it says installed and then no boot; creating flash drive and loading that remotely through kvm, no luck; dd-ing flash files to local drive meh; etc etc . After 8 hours I accidently loaded the 5.22 iso instead of the 6 and it installed immediatly. FFS, dont remove that beta or development tag from download, this is far from any stable...

Chupaka · Sun Dec 09, 2012 10:51 pm

Upgraded my semi-test x86 Intel router (with two 82576 + one 82574L NICs if it matters) from 5.22 to 6.0rc5 - no networking, any /interface print command ended in timeout + supout suggestion. I tried to make supout, but when NetInstalling v5, I checked 'Keep old configuration' - and as a result saw absolutely empty config with all files (including backups, f*ck!!!11oneone) erased, so I don't know how to extract supout from that router

p.s. in WinBox, one can change supout file name - how to do that in Terminal? "/system sup-output" doesn't have any parameters...
I don't understand - did you manage to make the file or not? Try to send to support if you have anything

yes, I managed to make supout. but I cannot get it from router - no network to download, and downgrading with NetInstall to v5 wipes all configuration and files even with 'Keep old configuration' checked

do I need to move HDD to Linux server for supout extracting?

the only think I noticed is that in v6 there are half a dozen devices marked as 'unknown' in resources/pci, while v5 shows them all normally

blingblouw · Mon Dec 10, 2012 1:21 pm

Fedora 15. Runs fine on all other versions fo ROS. (5.11 - 5.20)
KVM host sends ACPI event to the guest. Try to check if your fedora accepts them.

This happens only in 6.0rc5 so far.

I even created a RouterOS KVM and it too has the same result

[admin@Office] /kvm> shut-down RouterOS_MT
[admin@Office] /kvm> shut-down FedoraNEW
command execution failed!
[admin@Office] /kvm> shut-down RouterOS_MT
command execution failed!
[admin@Office] /kvm> shut-down RouterOS_MT
command execution failed!
[admin@Office] /kvm> shut-down FedoraNEW
command execution failed!
[admin@Office] /kvm> shut-down FedoraNEW
command execution failed!

Their states stay like this until the router (host) is manually restarted

11 name="FedoraNEW" cpu-count=1 memory=640MiB disk-images=hda:FedoraNEW kernel="" kernel-cmdline="" initrd="" vnc-server-address=0.0.0.0 vnc-server-display=11 snapshot=no state=restarting

12 name="RouterOS_MT" cpu-count=1 memory=128MiB disk-images=hda:RouterOS kernel="" kernel-cmdline="" initrd="" vnc-server-address=0.0.0.0 vnc-server-display=0 snapshot=no state=stopping

When the host is restarted so is the KVM BUT the original tap interfaces are not removed from the interface list

hci · Mon Dec 10, 2012 7:07 pm

Attempted to upgrade a RouterBOARD 951-2n for rc4 to rc5. Appears to be bricked. Solid PWR and ACT lights. Nothing else lights up. Any possible fixes besides RMA?

power it with pushed button, this will load secondary bootloader and run netinstall mode

Pushed and held reset button, powered up. Both Pwr and Act lights come on and never go out. Ethernet never comes up.

Mon Dec 10, 2012 7:16 pm

pushed and held reset button, powered up. Both Pwr and Act lights come on and never go out. Ethernet never comes up.

you have RB951-2N? did you try launching netinstall on the PC when device is in this state ?

hci · Mon Dec 10, 2012 7:22 pm

pushed and held reset button, powered up. Both Pwr and Act lights come on and never go out. Ethernet never comes up.

you have RB951-2N? did you try launching netinstall on the PC when device is in this state ?

Have Netinstall up but since the 951-2n will not bring up an ethernet link I don't think it will do any good. Have tried reset button many times now. Followed directions below for reset button and netinstall.

http://wiki.mikrotik.com/wiki/Manual:Netinstall

napismizpravu · Mon Dec 10, 2012 7:57 pm

proxy KO!
/ip proxy access print >> no listing

same error 5.22
http://forum.mikrotik.com/viewtopic.php ... =2#p344809

RB433UAH
5.22 max uptime 1d-3d
6.0rc5 max uptime 3d

send supout mikrotik?

edit:
winbox>reboot>ether off, routerboard frozen>power off-on>proxy enable, statistics access filters cleared, USB Flash confusion of names > power off-on> after start good

farzin · Tue Dec 11, 2012 5:05 pm

hi , thanks for the new release . but from 2 days ago that i have upgraded my 2 x86 routers , one of them is malfunctioning , i have described the problem of ip route cache increasing in the following topic :
http://forum.mikrotik.com/viewtopic.php?f=2&t=51127

and another buggy thing is that when i use /system reboot , it shut downs

estdata · Tue Dec 11, 2012 9:35 pm

how did you fix it?

hi, normis
routerboard 2011UAS-2HnD is supported for 6.0 RC5 version ?

meschaninovn · Wed Dec 12, 2012 3:03 am

I have a problem with ssh in 6.0rc5
An error was occured when i tried to connect to remote host..
- "mepty: session finished"

janisk · Wed Dec 12, 2012 11:10 am

we will fix it, in the mean time use New Terminal and ether there command '/system ssh <ip address>'

3bs · Wed Dec 12, 2012 11:40 am

And again not work igmp proxy

Wed Dec 12, 2012 11:41 am

And again not work igmp proxy

did it work in previous RC?

3bs · Wed Dec 12, 2012 11:43 am

did it work in previous RC?

no, it worked at rc2

Wed Dec 12, 2012 11:44 am

did it work in previous RC?
no, work at rc2

when you write "again", it means that it worked in rc4, but not in rc5. So to clarify - IGMP proxy is still not fixed (in any v6 version)

3bs · Wed Dec 12, 2012 1:30 pm

when you write "again", it means that it worked in rc4, but not in rc5. So to clarify - IGMP proxy is still not fixed (in any v6 version)

no, it worked in rc1 and rc2, from rc3 not work

Wed Dec 12, 2012 1:32 pm

when you write "again", it means that it worked in rc4, but not in rc5. So to clarify - IGMP proxy is still not fixed (in any v6 version)
no, it worked in rc1 and rc2, from rc3 not work

I can give you a test version, please email support for the link

3bs · Wed Dec 12, 2012 1:43 pm

I can give you a test version, please email support for the link

it would be great, bad3bs@gmail.com

thanks, but it dont include multicast package

honzam · Wed Dec 12, 2012 3:31 pm

RB711 wireless client. Simple configuration, only NAT and DHCP. Upgrade from rc5 to rc6 then 100% cpu
No routing on client. Only console and mac-telnet works. Winbox dont work after upgrade

ddejager · Wed Dec 12, 2012 4:38 pm

You answered my questions about USB storage so quickly...I have another question.

Again I have a RB2011UAS-2HnD board using v6rc5. I cannot get the "new" cable diagnostics to work as advertised. When I run the diagnostic for any ethernet port I get "status" and "auto-negotiation" reported back, but nothing about "cable-pairs". I've read in other postings that this only works on 5 of the 10 ports on this router (I forget if it was the gigabit or 100 mbit ports), but I cannot get it to work on any ports. I'm trying on ports that have no-link with various length cables plugged in.

Any suggestions?

Did anyone get the cable diagnostics to work on a RB2011UAS-2HnD?

Wed Dec 12, 2012 4:45 pm

Did anyone get the cable diagnostics to work on a RB2011UAS-2HnD?

Yes it works.

[admin@bumba] > /interface ethernet cable-test 0
         name: ether1
       status: no-link
  cable-pairs: open:0,open:0,open:0,open:0

Basiley · Wed Dec 12, 2012 4:59 pm

from [relatively]small things - dreaming about NAT-T support. also better handling PMP.

Wed Dec 12, 2012 5:30 pm

RB711 wireless client. Simple configuration, only NAT and DHCP. Upgrade from rc5 to rc6 then 100% cpu
No routing on client. Only console and mac-telnet works. Winbox dont work after upgrade

please redownload the latest RouterOS v6.0rc6 and test again. Make a support output file if you still see this problem and send to support@mikrotik.com

chojrak11 · Wed Dec 12, 2012 10:10 pm

Reverse Path Filtering finally implemented! Thanks Mikrotik

After updating a few routers to 6.0rc5 I observe "RX Drops" which weren't counted in 5.21. I'm not quite sure what would be causing it -- the routers are different hardware on different networks and different topologies (one with VLANs, the other without etc.) Everything seems to work just fine, as it did on 5.21, just the stats are alarming. But in interface details they're all zeros. I tried to log those drops trying topic "interface" but nothing appeared in the log.

See the screen below. Thanks.

ether_stats.png

tcmeggs · Thu Dec 13, 2012 3:42 am

I installed this and previously my RB433AH had no problems handling 50MB of inbound traffic. After upgrading to v6rc5 it seems to cap at around 10-12mb inbound on ether1 and starts to drop pings, cpu and memory slowly climbs.

ddejager · Thu Dec 13, 2012 11:03 pm

Did anyone get the cable diagnostics to work on a RB2011UAS-2HnD?
Yes it works.
Code: Select all
[admin@bumba] > /interface ethernet cable-test 0
         name: ether1
       status: no-link
  cable-pairs: open:0,open:0,open:0,open:0

Interesting because on my router the exact same command does not produce the cable-pairs: line. Any suggestions?

paoloaga · Thu Dec 13, 2012 11:07 pm

Interesting because on my router the exact same command does not produce the cable-pairs: line. Any suggestions?

Check that routerboot is upgraded to the latest version.

ddejager · Thu Dec 13, 2012 11:56 pm

Did anyone get the cable diagnostics to work on a RB2011UAS-2HnD?
Yes it works.
Code: Select all
[admin@bumba] > /interface ethernet cable-test 0
         name: ether1
       status: no-link
  cable-pairs: open:0,open:0,open:0,open:0
Interesting because on my router the exact same command does not produce the cable-pairs: line. Any suggestions?

I think I figured out the problem. It seems that the cable-test will not work if the ethernet switch port is a master-port for other switch ports. When the switch port is a master port, the status shows up as "link-ok" even if the physical port has no device connected. When in the link-ok state, the cable-test will not report the cable-pairs. I wonder if this is a bug?

payday · Fri Dec 14, 2012 12:08 am

Did anyone get the cable diagnostics to work on a RB2011UAS-2HnD?
Yes it works.
Code: Select all
[admin@bumba] > /interface ethernet cable-test 0
         name: ether1
       status: no-link
  cable-pairs: open:0,open:0,open:0,open:0
Interesting because on my router the exact same command does not produce the cable-pairs: line. Any suggestions?

More interesting is that it works well on one of my RB2011UAS-2HnD and it doesn't on another one

. Both are running v6.0rc5. Only difference is that the one (that has this feature working) has bridged ports and second one (on which this feature doesn't work) has switched ports (using "master port" option).

Correction: It was on v6.0rc4. Now it doesn't work on both.

publicreg · Fri Dec 14, 2012 1:11 pm

Hi,

i have problem with usb UPS on RB751U-2Hnd.

version 5.22 - works
version 6.0rc4 - not works
version 6.0rc5 - not works

[admin@rb751u] > system resource usb print
 # DEVICE VENDOR                                             NAME                                             SPEED                                            
 0 1:1    Linux 3.3.5 ehci_hcd                               RB400 EHCI                                       480 Mbps                                         
 1 1:2    APC                                                Back-UPS ES 700G FW:871.O2 .I USB FW:O2          1.5 Mbps

[admin@rb751u] > system ups add port=usb1
input does not match any value of port

i also tested UPS support on RB493G ROSv6_rc4 and there works without problem.

Dan

napismizpravu · Fri Dec 14, 2012 8:46 pm

RB433UAH

proxy error + profile + ? http://forum.mikrotik.com/viewtopic.php ... =1#p346441 uptime 2d 9h (can not create supout routerboard frozen)

power off-on no view "Cache Drive" ( winbox,web),winbox reboot OK

what is fixed in the current version 6.0rc6? (add NTP server packages test assembly)

napismizpravu · Mon Dec 17, 2012 1:02 am

terminal:
system resource pci pr

6.0rc5
miniPCI CM10 > AR5413 802.11abg NIC (rev: 1)
miniPCI R52H > AR5413 802.11abg NIC (rev: 1)

5.22
miniPCI TP-LINK TL-WN360G > AR5007G Wireless Network Adapter (rev: 1)

chaos miniPCI chipset?

Mon Dec 17, 2012 9:56 am

terminal:
system resource pci pr

6.0rc5
miniPCI CM10 > AR5413 802.11abg NIC (rev: 1)
miniPCI R52H > AR5413 802.11abg NIC (rev: 1)

5.22
miniPCI TP-LINK TL-WN360G > AR5007G Wireless Network Adapter (rev: 1)

chaos miniPCI chipset?

the card itself isn't reporting the name of the chip, so we show generic driver that is used. it will not always match with the actual chipset.

Mon Dec 17, 2012 10:31 am

If anyone is posting Winbox problems, make sure you are tesing with latest Winbox.exe from the RC5 router, and that you are using The IP ADDRESS TO CONNECT. MAC connection is not stable, and don't use it unless IP connection is not available.

napismizpravu · Mon Dec 17, 2012 9:59 pm

RB433UAH

http://forum.mikrotik.com/viewtopic.php ... =2#p346441

uptime 3d 00h 40m +-

scheduler destroy skript RouterOS ?

Parallel download (tool fetch address=) error RouterOS ?

I have deactivated script scheduled, watchdog off.

chojrak11 · Tue Dec 18, 2012 4:21 am

If anyone is posting Winbox problems, make sure you are tesing with latest Winbox.exe from the RC5 router.

Thanks for the suggestion, after downloading fresh Winbox.exe (123KB) no changes to my RX Drops problem. Still the same -- all stats are zero in "RX Stats" tab of an interface, nonzero and raising in Interface List window... (so far on RB433AH, RB411AR, RB411UAHR, RB532, on VLAN, Bridge and plain Ethernet). See my previous post above for screenshot and details.

chojrak11 · Wed Dec 19, 2012 5:47 am

Reverse Path Filtering finally implemented! Thanks Mikrotik
After updating a few routers to 6.0rc5 I observe "RX Drops" which weren't counted in 5.21.

Mikrotik support answered me that RX Drops represent packets that were received by the router, but weren't destined for it. So it's nothing new, it just started to count them properly

grg · Wed Dec 19, 2012 9:21 am

I cannot find ROS v6.0rc5 tile package download on MikroTik web site for new CCR devices. I'm looking for extra package: NTP. Is this something that has to be addressed through MikroTik support?

Thanks.

doush · Wed Dec 19, 2012 4:55 pm

Did you receive the CCR ?

grg · Wed Dec 19, 2012 5:19 pm

Did you receive the CCR ?

Yes.

doush · Wed Dec 19, 2012 5:44 pm

Lucky you ! Whats the version on it ?

honzam · Wed Dec 19, 2012 7:17 pm

Did you receive the CCR ?
Yes.

On development site is 6.0rc6 for TILE

grg · Wed Dec 19, 2012 9:53 pm

Lucky you ! Whats the version on it ?

Device: CCR1036-12G-4S
Software: RouterOs v6.0rc5

grg · Wed Dec 19, 2012 10:04 pm

Did you receive the CCR ?
Yes.
On development site is 6.0rc6 for TILE

This development site you are talking about, is it for "selected" people only? I don't think I have seen such before.

honzam · Wed Dec 19, 2012 11:03 pm

Write support@mikrotik.com to access pre-release version http://www.mikrotik.com/download/share/ ... 6.0rc6.npk

MT support - CCR is already at end users. Put the download link on main page (rc5 or rc6)

napismizpravu · Thu Dec 20, 2012 3:11 am

RB433UAH

http://forum.mikrotik.com/viewtopic.php ... =2#p346441

uptime 3d 00h 40m +-

scheduler destroy skript RouterOS ?

Parallel download (tool fetch address=) error RouterOS ?

I have deactivated script scheduled, watchdog off.

same problem (script scheduled deactivated) uptime 2d 4h proxy, profile info KO

metarouter, samba, NAT work OK

again error winbox reboot > routerboard frozen> power off-on > working

I use a proxy to block ads webpages.

Nick Kett · Fri Dec 21, 2012 6:55 am

upgraded from 5.7 directly to 6rc5 on a RB1100AHx2.
Ethernet1 (first physical port) went missing from my configuration, ie was not to be seen in winbox (lucky I was connected via a different port)
The port was configuered as a slave on a bonding interface.. it was missing there to and could not be seen to re-select.
Downgraded back to 5.22... like "magic" ethernet port was visiable again.
Can send rif file if wanted .
What email address?

Who is online