Community discussions

 
lscrlstld
just joined
Topic Author
Posts: 18
Joined: Fri Jun 08, 2007 2:09 am

VRRP interface always Invalid State

Tue Mar 12, 2013 4:21 pm

Hi,

I just add the new VRRP interface to ether interface, but the VRRP interface always invalid.
I use the defaults values, and very simple config.

/interface vrrp add interface=ether2
/interface vrrp print
Flags: X - disabled, I - invalid, R - running, M - master, B - backup
# NAME INTERFACE MAC-ADDRESS VRI PRI INTERVAL V V3..
0 I vrrp1 ether2 00:00:5E:00:01:01 1 100 1s 3 ipv4
/interface ethernet print
Flags: X - disabled, R - running, S - slave
# NAME MTU MAC-ADDRESS ARP MASTER-PORT SWITCH
0 R ether1 1500 D4:CA:6D:3D:FF:74 enabled
1 R ether2 1500 D4:CA:6D:3D:FF:75 enabled none switch1

/system resource print
uptime: 17m19s
version: 5.24
free-memory: 52856KiB
total-memory: 62184KiB
cpu: MIPS 24Kc V7.4
cpu-count: 1
cpu-frequency: 300MHz
cpu-load: 2%
free-hdd-space: 30276KiB
total-hdd-space: 61440KiB
write-sect-since-reboot: 311
write-sect-total: 159992
bad-blocks: 0.1%
architecture-name: mipsbe
board-name: RB450

well... is it a bug ?

How to it UP ???
 
nmaton
Frequent Visitor
Frequent Visitor
Posts: 72
Joined: Fri Feb 18, 2011 12:31 am

Re: VRRP interface always Invalid State

Tue Mar 12, 2013 4:51 pm

it won't come up until you provide ip addresses on the vrrp interface and on the physical interface.
Nicolas Maton
nicolasmaton@gmail.com

CCNA/ CCDA
MTCNA / MTCTCE

Available for Mikrotik Consulting
 
lscrlstld
just joined
Topic Author
Posts: 18
Joined: Fri Jun 08, 2007 2:09 am

Re: VRRP interface always Invalid State

Tue Mar 12, 2013 10:53 pm

it won't come up until you provide ip addresses on the vrrp interface and on the physical interface.
Good man!!! All right now! tks!

Is it documented ?
 
nmaton
Frequent Visitor
Frequent Visitor
Posts: 72
Joined: Fri Feb 18, 2011 12:31 am

Re: VRRP interface always Invalid State

Wed Mar 13, 2013 11:12 am

it won't come up until you provide ip addresses on the vrrp interface and on the physical interface.
Good man!!! All right now! tks!

Is it documented ?
i think this is the most information you can find:

http://wiki.mikrotik.com/wiki/Manual:Interface/VRRP
Nicolas Maton
nicolasmaton@gmail.com

CCNA/ CCDA
MTCNA / MTCTCE

Available for Mikrotik Consulting
 
User avatar
mrz
MikroTik Support
MikroTik Support
Posts: 5942
Joined: Wed Feb 07, 2007 12:45 pm
Location: Latvia
Contact:

Re: VRRP interface always Invalid State

Wed Mar 13, 2013 11:15 am

Minimal config required is in the manual examples
http://wiki.mikrotik.com/wiki/VRRP-examples

Who is online

Users browsing this forum: Google [Bot] and 120 guests