Community discussions

MUM Europe 2020
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

What's new in 6.8rc1

Thu Jan 02, 2014 4:07 pm

What's new in 6.8rc1 (2014-Jan-02 09:46):

*) bgp - don't show community 'internet' in BGP advertisements;
*) ipsec - enable hardware acceleration for aes-cbc-128 + md5|sha1|sha256 aead on tilera cpus;
*) ospf - fixed checksum calculation for OSPFv3 AS-external-LSAs;
*) default configuration - changed dhcp server lease time to 10 minutes;
*) fixed port isolation on CRSs (bug introduced in v6.6);
*) smb - added support for SMB 2.002
*) timezone information updated;
*) ppp - fixed ppp bridging (did not work since v6.6);
*) improved speed of PPP, PPPoE, PPTP & L2TP on multicore routers;
*) address-list - fix crash when adding two identical address list entries (not allowed any more);
*) fixed multicast forwarding on CCRs;
LAN, FTTx, Wireless. ISP operator
 
Duduhandelman
Frequent Visitor
Frequent Visitor
Posts: 89
Joined: Wed Jan 04, 2012 5:30 pm

Re: What's new in 6.8rc1

Fri Jan 03, 2014 11:51 am

Does anyone tested ipsec on ccr now? I wonder if it will take 1G.
 
voxframe
Member Candidate
Member Candidate
Posts: 126
Joined: Thu Dec 16, 2010 2:51 pm

Re: What's new in 6.8rc1

Fri Jan 03, 2014 4:24 pm

6.8rc1 kills L2TP on CCR for me.

Not sure if perhaps this is a setup issue, but any other version of ROS it works. Move to 6.8rc1, it breaks. Move back 1 version, it works again.

I don't have time to troubleshoot or produce supout files as this is sadly in production (Stupid me)

Does anyone else notice L2TP issues? Or serious changes over the versions that could cause my config to need to be changed?
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Fri Jan 03, 2014 4:32 pm

Make sure to upgrade to todays build (always)
No answer to your question? How to write posts
 
voxframe
Member Candidate
Member Candidate
Posts: 126
Joined: Thu Dec 16, 2010 2:51 pm

Re: What's new in 6.8rc1

Mon Jan 06, 2014 9:04 pm

I can't risk any more games with this router. It's in production (Again my stupid mistake)

Please confirm if there was a known L2TP bug between these releases. Simple question.
 
Petzl
Member Candidate
Member Candidate
Posts: 207
Joined: Sun Jun 30, 2013 12:14 pm

Re: What's new in 6.8rc1

Mon Jan 06, 2014 11:38 pm

I did a upgrade + reset on my CRS

Now is all working fine (before only 10mbit if one of the devices was 10 mbit)
Also did a board firmware upgrade
 
wispwest
Member
Member
Posts: 477
Joined: Tue May 19, 2009 3:48 am

Re: What's new in 6.8rc1

Tue Jan 07, 2014 6:02 pm

you guys should re-name it to RC2 if there's a revision. I just re-downloaded it as the same file, same size, just different dates on it. I can't even tell what was changed from the Jan 2nd and the one released back in December
 
efaden
Forum Guru
Forum Guru
Posts: 1711
Joined: Sat Mar 30, 2013 1:55 am
Location: New York, USA

Re: What's new in 6.8rc1

Tue Jan 07, 2014 6:04 pm

you guys should re-name it to RC2 if there's a revision. I just re-downloaded it as the same file, same size, just different dates on it. I can't even tell what was changed from the Jan 2nd and the one released back in December
+1... generally new releases have different version numbers. I have never seen anyone release a new version (different build times, etc) with the same version numbers.
 
wispwest
Member
Member
Posts: 477
Joined: Tue May 19, 2009 3:48 am

Re: What's new in 6.8rc1

Tue Jan 07, 2014 6:09 pm

absolutely horrible. I have a PtP I just tested this on. It would link up for about 10-20 seconds, then stay registered, but the rates would drop to 6/162 and not pass any traffic until "-" I minus it off the Master forcing it to re-register, and the process repeats.

if you have any wireless or point-to-points, don't use this firmware!
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Tue Jan 07, 2014 7:58 pm

you guys should re-name it to RC2 if there's a revision. I just re-downloaded it as the same file, same size, just different dates on it. I can't even tell what was changed from the Jan 2nd and the one released back in December
+1... generally new releases have different version numbers.
+2. Make better naming. RC2, RC3 etc....
LAN, FTTx, Wireless. ISP operator
 
User avatar
kometchtech
Member Candidate
Member Candidate
Posts: 194
Joined: Sat Jun 15, 2013 4:25 am
Location: Japan
Contact:

Re: What's new in 6.8rc1

Tue Jan 07, 2014 8:04 pm

you guys should re-name it to RC2 if there's a revision. I just re-downloaded it as the same file, same size, just different dates on it. I can't even tell what was changed from the Jan 2nd and the one released back in December
+1... generally new releases have different version numbers.
+2. Make better naming. RC2, RC3 etc....
+1

I want you to put in the file name, date at least if it is not.
--
Routerboard Users Group JP
http://www.rb-ug.jp/
CCR1009-8G-1S-1S+, RB750Gr3, CRS226-24G-2S+, RB850Gx2, RB960PGS, CRS317-1G-16S+,
RB2011UAS, CRS125-24G-1S, RB962UiGS-5HacT2HnT, CRS212-1G-10S-1S+, RB3011UiAS
 
User avatar
nz_monkey
Forum Guru
Forum Guru
Posts: 1825
Joined: Mon Jan 14, 2008 1:53 pm
Location: Straya
Contact:

Re: What's new in 6.8rc1

Wed Jan 08, 2014 2:54 am

you guys should re-name it to RC2 if there's a revision. I just re-downloaded it as the same file, same size, just different dates on it. I can't even tell what was changed from the Jan 2nd and the one released back in December
+1... generally new releases have different version numbers.
+2. Make better naming. RC2, RC3 etc....
+4
http://thebrotherswisp.com/ | Mikrotik MTCNA, MTCRE, MTCINE | Fortinet FTCNA, FCNSP, FCT | Extreme Networks ENA
 
User avatar
cbrown
Trainer
Trainer
Posts: 1840
Joined: Thu Oct 14, 2010 8:57 pm
Contact:

Re: What's new in 6.8rc1

Wed Jan 08, 2014 3:24 am

+1
C.Brown

cbrown[at]ravenrocknetworks.com
MTCNA - MTCRE - MTCWE - MTCTCE
MTCSE - TRAINER-0179
 
maxiscool
just joined
Posts: 11
Joined: Mon Nov 11, 2013 10:47 am

Re: What's new in 6.8rc1

Wed Jan 08, 2014 3:41 pm

Hi Norman,

Can you assist to check on the following ticket that I've report to support team? Being a month already however I did not get any response after which from my correspond to check for update.
http://forum.mikrotik.com/viewtopic.php?f=2&t=80298

Please at least let me know if someone is looking into this issue to be fix? Do that need more time to check?
 
nkourtzis
Member Candidate
Member Candidate
Posts: 206
Joined: Tue Dec 11, 2012 12:56 am
Location: Greece

Re: What's new in 6.8rc1

Wed Jan 08, 2014 5:16 pm

absolutely horrible. I have a PtP I just tested this on. It would link up for about 10-20 seconds, then stay registered, but the rates would drop to 6/162 and not pass any traffic until "-" I minus it off the Master forcing it to re-register, and the process repeats.

if you have any wireless or point-to-points, don't use this firmware!

The same here. Checked on an Omnitik as AP and a Sextant as client, with an NV2 link between them (actually it is a PtMP link with more clients, but I upgraded only one of them).

It seems to me that the time before the problem kicks in depends heavily on the amount of traffic flowing through the wireless link: more traffic and the link goes down within seconds; less traffic and it can stay on for a day or more.

Downgraded the AP (Omnitik) to 6.7 and it became stable. The Sextant, still on 6.8 rc1, remained unstable. When the latter was also downgraded, the link became stable again.

I wonder if this means that there is some work going on under the hood on the wireless section... :wink:
Passionate about networks
Enthusiastic about Mikrotik
MTCNA | MTCRE | MTCINE

No trees were killed to send this message,
but a large number of electrons were terribly inconvenienced.
 
derliang
just joined
Posts: 6
Joined: Thu Oct 03, 2013 5:52 pm

Re: What's new in 6.8rc1

Thu Jan 09, 2014 4:16 am

Try the newest version 6.8RC1(2014-01-08 14:00:28)。
L2TP work fine for me:)
 
uldis
MikroTik Support
MikroTik Support
Posts: 3427
Joined: Mon May 31, 2004 2:55 pm

Re: What's new in 6.8rc1

Thu Jan 09, 2014 3:25 pm

wispwest and nkourtzis, we were able to reproduce this problem. We fixed this problem, you can redownload the v6.8rc1 - Nv2 should work stable
again.
 
evharten
newbie
Posts: 33
Joined: Mon Apr 30, 2012 8:20 am
Location: Capelle a/d IJssel, The Netherlands
Contact:

Re: What's new in 6.8rc1

Fri Jan 10, 2014 7:45 am

Hey Uldis,

Could you take a look at: http://forum.mikrotik.com/viewtopic.php?f=1&t=80421
So far every 6.8rc1 build since this year (starting from the 2-1-2014 build), give kernel panics.
Cannot create supouts sadly, because of the reboots the kernel panic issues, it keeps rebooting in a loop.
https://www.mikroshop.nl - The Dutch Mikrotik Store!
 
uldis
MikroTik Support
MikroTik Support
Posts: 3427
Joined: Mon May 31, 2004 2:55 pm

Re: What's new in 6.8rc1

Fri Jan 10, 2014 3:44 pm

Hey Uldis,

Could you take a look at: http://forum.mikrotik.com/viewtopic.php?f=1&t=80421
So far every 6.8rc1 build since this year (starting from the 2-1-2014 build), give kernel panics.
Cannot create supouts sadly, because of the reboots the kernel panic issues, it keeps rebooting in a loop.
we fixed this problem, you can redownload the v6.8rc1.
 
w0lt
Member
Member
Posts: 486
Joined: Wed Apr 02, 2008 2:12 pm
Location: Minnesota USA

Re: What's new in 6.8rc1

Fri Jan 10, 2014 9:09 pm

Hey Uldis,

Could you take a look at: http://forum.mikrotik.com/viewtopic.php?f=1&t=80421
So far every 6.8rc1 build since this year (starting from the 2-1-2014 build), give kernel panics.
Cannot create supouts sadly, because of the reboots the kernel panic issues, it keeps rebooting in a loop.
we fixed this problem, you can redownload the v6.8rc1.

If you changed something to fix it, shouldn't you really call that v6.8rc2 ? Sort of confusing when you change things or fix something and call it the same release.
MTCNA - 2011

" The Bitterness of Poor Quality Remains Long After the Sweetness of Low Price is Forgotten "

Image
 
User avatar
Chupaka
Forum Guru
Forum Guru
Posts: 8320
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: What's new in 6.8rc1

Fri Jan 10, 2014 9:19 pm

If you changed something to fix it, shouldn't you really call that v6.8rc2 ? Sort of confusing when you change things or fix something and call it the same release.
http://en.wikipedia.org/wiki/Continual_ ... nt_process
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
rdhw
just joined
Posts: 17
Joined: Wed Jun 01, 2011 12:31 am

Re: What's new in 6.8rc1

Mon Jan 13, 2014 2:31 pm

What's new in 6.8rc1 (2014-Jan-02 09:46):

*) improved speed of PPP, PPPoE, PPTP & L2TP on multicore routers
Will this update include a fix for Ticket#2011122766000641, concerning packet loss if PPP packets arrive out of order?
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Mon Jan 13, 2014 10:19 pm

What's new in 6.8rc1 (2014-Jan-10 13:52):

*) dhcp client - support interfaces in bridge;
*) dhcp - parse decimal strings and IP addreses in options value;
*) bgp - don't show community 'internet' in BGP advertisements;
*) ipsec - enable hardware acceleration for aes-cbc-128 + md5|sha1|sha256 aead on tilera cpus;
*) ospf - fixed checksum calculation for OSPFv3 AS-external-LSAs;
*) default configuration - changed dhcp server lease time to 10 minutes;
*) fixed port isolation on CRSs (bug introduced in v6.6);
*) smb - added support for SMB 2.002
*) timezone information updated;
*) ppp - fixed ppp bridging (did not work since v6.6);
*) improved speed of PPP, PPPoE, PPTP & L2TP on multicore routers;
*) address-list - fix crash when adding two identical address list entries (not allowed any more);
*) fixed multicast forwarding on CCRs;
*) firewall - improved address-type matcher, and added it for ipv6 aswell;
LAN, FTTx, Wireless. ISP operator
 
dw5304
Frequent Visitor
Frequent Visitor
Posts: 51
Joined: Tue Apr 12, 2011 9:36 pm

Re: What's new in 6.8rc1

Wed Jan 15, 2014 2:59 am

where to obtain said download?
 
p2systems
just joined
Posts: 8
Joined: Sun Aug 28, 2011 10:27 pm

Re: What's new in 6.8rc1

Wed Jan 15, 2014 3:46 pm

You Need to have "Development version testing" Access on main mikrotik.com page.
BTW new build online
What's new in 6.8rc1 (2014-Jan-15 12:45):
 
evharten
newbie
Posts: 33
Joined: Mon Apr 30, 2012 8:20 am
Location: Capelle a/d IJssel, The Netherlands
Contact:

Re: What's new in 6.8rc1

Thu Jan 16, 2014 6:30 am

The 15-01-2014 build fixes the kernel panics!
https://www.mikroshop.nl - The Dutch Mikrotik Store!
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Thu Jan 16, 2014 10:01 am

The 15-01-2014 build fixes the kernel panics!
On what type routerboard?
LAN, FTTx, Wireless. ISP operator
 
rdhw
just joined
Posts: 17
Joined: Wed Jun 01, 2011 12:31 am

Re: What's new in 6.8rc1

Thu Jan 16, 2014 12:08 pm

You Need to have "Development version testing" Access on main mikrotik.com page.
How do I obtain this?
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Thu Jan 16, 2014 12:19 pm

You Need to have "Development version testing" Access on main mikrotik.com page.
How do I obtain this?
write to support@mikrotik.com
LAN, FTTx, Wireless. ISP operator
 
evharten
newbie
Posts: 33
Joined: Mon Apr 30, 2012 8:20 am
Location: Capelle a/d IJssel, The Netherlands
Contact:

Re: What's new in 6.8rc1

Thu Jan 16, 2014 5:33 pm

The 15-01-2014 build fixes the kernel panics!
On what type routerboard?
CCR1016-12G
https://www.mikroshop.nl - The Dutch Mikrotik Store!
 
User avatar
kometchtech
Member Candidate
Member Candidate
Posts: 194
Joined: Sat Jun 15, 2013 4:25 am
Location: Japan
Contact:

Re: What's new in 6.8rc1

Fri Jan 17, 2014 7:12 am

Updates 6.8rc1, which is published 2014-01-16 What?
Contents are worried about the release notes has not been updated.
--
Routerboard Users Group JP
http://www.rb-ug.jp/
CCR1009-8G-1S-1S+, RB750Gr3, CRS226-24G-2S+, RB850Gx2, RB960PGS, CRS317-1G-16S+,
RB2011UAS, CRS125-24G-1S, RB962UiGS-5HacT2HnT, CRS212-1G-10S-1S+, RB3011UiAS
 
User avatar
NetHorror
just joined
Posts: 17
Joined: Fri Dec 06, 2013 8:12 am

Re: What's new in 6.8rc1

Fri Jan 17, 2014 3:11 pm

+5 for correct naming of builds. RC2... RC3... RC444 :)
MTCNA, MTCRE, MTCTCE, MTCWE
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Fri Jan 17, 2014 3:19 pm

Our system is built in a way, that we can change these numbers if we release these versions. Currently we don't release them, they are internal "patches" of previous builds. We would have to do something differently then. But as you know, these are unofficial internal releases anyway.
No answer to your question? How to write posts
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Fri Jan 17, 2014 3:20 pm

deleted
Last edited by honzam on Fri Jan 17, 2014 3:23 pm, edited 1 time in total.
LAN, FTTx, Wireless. ISP operator
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Fri Jan 17, 2014 3:22 pm

+5 for correct naming of builds. RC2... RC3... RC444 :)
Normis, why Mikrotik don´t hear these requests?
See above
No answer to your question? How to write posts
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Fri Jan 17, 2014 3:24 pm

Release date? Today?
LAN, FTTx, Wireless. ISP operator
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Fri Jan 17, 2014 3:25 pm

No, not today. The changes we are making, are not yet finished.
No answer to your question? How to write posts
 
andriys
Forum Guru
Forum Guru
Posts: 1192
Joined: Thu Nov 24, 2011 1:59 pm
Location: Kharkiv, Ukraine

Re: What's new in 6.8rc1

Fri Jan 17, 2014 6:54 pm

Our system is built in a way, that we can change these numbers if we release these versions. Currently we don't release them, they are internal "patches" of previous builds. We would have to do something differently then. But as you know, these are unofficial internal releases anyway.
Add some sort of sequence number to your internal build names. Timestamp of when the build begins or revision number should work.
 
tgcnet
just joined
Posts: 15
Joined: Fri Jan 18, 2008 3:26 am

Re: What's new in 6.8rc1

Mon Jan 20, 2014 5:01 am

high ping to station pppoe in 6.8.rc1 build 16/01/2014....... in 6.6 1ms..
You do not have the required permissions to view the files attached to this post.
 
gogusrl
newbie
Posts: 25
Joined: Sat Aug 18, 2012 1:01 pm

Re: What's new in 6.8rc1

Tue Jan 21, 2014 1:02 pm

*) improved speed of PPP, PPPoE, PPTP & L2TP on multicore routers;

Can confirm I got another ~200 mbps while torrenting on my 1gbps connection running routeros 6.8rc1 under ESXi on a Celeron G1610T (sole VM, ~70% cpu load, pppoe connection, ~60 firewall rules).
 
ddejager
Member Candidate
Member Candidate
Posts: 109
Joined: Tue Oct 18, 2011 5:13 am

Re: What's new in 6.8rc1

Tue Jan 21, 2014 11:01 pm

I reported a problem with Quickset crashing the router in 6.7. This problem was acknowledged by support and I was told MikroTik would try to fix it in the next release. The ticket is #2013120766000022

Will this be fixed in 6.8?
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Wed Jan 22, 2014 8:17 am

I reported a problem with Quickset crashing the router in 6.7. This problem was acknowledged by support and I was told MikroTik would try to fix it in the next release. The ticket is #2013120766000022

Will this be fixed in 6.8?
You can test the latest build and see:
http://www.mikrotik.com/download/share/ ... 6.8rc1.npk
No answer to your question? How to write posts
 
mietus
Member Candidate
Member Candidate
Posts: 122
Joined: Mon Jan 30, 2006 11:14 pm
Location: Poland

Re: What's new in 6.8rc1

Wed Jan 22, 2014 11:18 am

What's new in 6.8rc1 (2014-Jan-21 11:25):

*) wireless - improved 11n and nv2 stability;
*) dhcp client - support interfaces in bridge;
*) dhcp - parse decimal strings and IP addreses in options value;
*) bgp - don't show community 'internet' in BGP advertisements;
*) ipsec - enable hardware acceleration for aes-cbc + md5|sha1|sha256 aead on tilera cpus;
*) ospf - fixed checksum calculation for OSPFv3 AS-external-LSAs;
*) default configuration - changed dhcp server lease time to 10 minutes;
*) fixed port isolation on CRSs (bug introduced in v6.6);
*) smb - added support for SMB 2.002
*) timezone information updated;
*) ppp - fixed ppp bridging (did not work since v6.6);
*) improved speed of PPP, PPPoE, PPTP & L2TP on multicore routers;
*) address-list - fix crash when adding two identical address list entries (not allowed any more);
*) fixed multicast forwarding on CCRs;
*) firewall - improved address-type matcher, and added it for ipv6 aswell;

MT: A bit more info about nv2 and n information? ;)
 
skibi82
newbie
Posts: 42
Joined: Fri Mar 22, 2013 7:09 pm

Re: What's new in 6.8rc1

Wed Jan 22, 2014 8:34 pm

You can see that support in recent times does not give advice.
What's new edition of the old mistakes.

Even I do not know it seems that the problem only on RB951G 6.8rc1 on the second router CRS125 all ok
You do not have the required permissions to view the files attached to this post.
 
tgcnet
just joined
Posts: 15
Joined: Fri Jan 18, 2008 3:26 am

Re: What's new in 6.8rc1

Wed Jan 22, 2014 11:49 pm

serious problem with PPPOE SERVER bridge and when client disconnects, the other customers mikrotik drops after 20 seconds, problem with BCP, in all versions,. customer who left hung equipment, and the right client mikrotik disconnected, after 20 seconds than the other turned off the device.
You do not have the required permissions to view the files attached to this post.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Thu Jan 23, 2014 1:37 pm

You can see that support in recent times does not give advice.
What's new edition of the old mistakes.

Even I do not know it seems that the problem only on RB951G 6.8rc1 on the second router CRS125 all ok
Did you contact support? Please tell me the ticket number and I will check what is wrong there
No answer to your question? How to write posts
 
uldis
MikroTik Support
MikroTik Support
Posts: 3427
Joined: Mon May 31, 2004 2:55 pm

Re: What's new in 6.8rc1

Thu Jan 23, 2014 1:41 pm

mietus, some possible nv2 lockups/crash are fixed and also speed for the 802.11n might be more stable.
 
zyzelis
Member Candidate
Member Candidate
Posts: 213
Joined: Sun Apr 08, 2012 9:25 pm

Re: What's new in 6.8rc1

Thu Jan 23, 2014 2:45 pm

mietus, some possible nv2 lockups/crash are fixed and also speed for the 802.11n might be more stable.
And it seems with nv2 ping isnt jumping like before, now stable 3ms under 40/40mbit btest.

its better Mtik, now its really better :D
 
mietus
Member Candidate
Member Candidate
Posts: 122
Joined: Mon Jan 30, 2006 11:14 pm
Location: Poland

Re: What's new in 6.8rc1

Thu Jan 23, 2014 3:21 pm

mietus, some possible nv2 lockups/crash are fixed and also speed for the 802.11n might be more stable.

mmmm very nice. ;]
 
ste
Forum Guru
Forum Guru
Posts: 1815
Joined: Sun Feb 13, 2005 11:21 pm

Re: What's new in 6.8rc1

Thu Jan 23, 2014 5:04 pm

mietus, some possible nv2 lockups/crash are fixed and also speed for the 802.11n might be more stable.
:D Realy good news! You've to clean code while integrating .ac 8)
 
User avatar
nz_monkey
Forum Guru
Forum Guru
Posts: 1825
Joined: Mon Jan 14, 2008 1:53 pm
Location: Straya
Contact:

Re: What's new in 6.8rc1

Thu Jan 23, 2014 10:42 pm

mietus, some possible nv2 lockups/crash are fixed and also speed for the 802.11n might be more stable.
:D Realy good news! You've to clean code while integrating .ac 8)
Or finishing off Wireless Controller 8)
http://thebrotherswisp.com/ | Mikrotik MTCNA, MTCRE, MTCINE | Fortinet FTCNA, FCNSP, FCT | Extreme Networks ENA
 
nkukard
just joined
Posts: 6
Joined: Tue Sep 16, 2008 3:46 pm
Contact:

Re: What's new in 6.8rc1

Thu Jan 23, 2014 11:26 pm

What's new in 6.8rc1 (2014-Jan-21 11:25):

*) wireless - improved 11n and nv2 stability;
*) dhcp client - support interfaces in bridge;
*) dhcp - parse decimal strings and IP addreses in options value;
*) bgp - don't show community 'internet' in BGP advertisements;
*) ipsec - enable hardware acceleration for aes-cbc + md5|sha1|sha256 aead on tilera cpus;
*) ospf - fixed checksum calculation for OSPFv3 AS-external-LSAs;
*) default configuration - changed dhcp server lease time to 10 minutes;
*) fixed port isolation on CRSs (bug introduced in v6.6);
*) smb - added support for SMB 2.002
*) timezone information updated;
*) ppp - fixed ppp bridging (did not work since v6.6);
*) improved speed of PPP, PPPoE, PPTP & L2TP on multicore routers;
*) address-list - fix crash when adding two identical address list entries (not allowed any more);
*) fixed multicast forwarding on CCRs;
*) firewall - improved address-type matcher, and added it for ipv6 aswell;

Definitly not fixed. 2 CRS125's back to back with VLAN trunking has both switches opposite eachother traffic repeated on all ports.

Issues still present:
unicast-fdb is populated with incorrect data (port is always set to 24 regardless of any setting)
isolation level per vlan cannot be set
svl cannot bet set per vlan, reboot clears it
mac-level isolation cannot be saved, reboot clears it
vlan-level isolation cannot be saved, reboot clears it
AllWorldIT.com - Sponsors and maintainers of opensource radius server SMRadius.
Commercial support, customizations & SLA's available.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Fri Jan 24, 2014 8:53 am

:D Realy good news! You've to clean code while integrating .ac
Or finishing off Wireless Controller
Which one would you prefer ?
No answer to your question? How to write posts
 
Lupin
Member Candidate
Member Candidate
Posts: 265
Joined: Mon Feb 16, 2009 10:22 pm
Location: Italy

Re: What's new in 6.8rc1

Fri Jan 24, 2014 9:11 am

*) wireless - improved 11n and nv2 stability;
Normis :shock: !!! Fantastic news!
You are working/improving NV2 protocol and wireless section!!!!!!!!!

Can you give us some more details of this change?
Improve throughput / latency? It solves some stalemate?

Can we try it? If so, where is the download link?
 
uldis
MikroTik Support
MikroTik Support
Posts: 3427
Joined: Mon May 31, 2004 2:55 pm

Re: What's new in 6.8rc1

Fri Jan 24, 2014 9:42 am

*) wireless - improved 11n and nv2 stability;
Normis :shock: !!! Fantastic news!
You are working/improving NV2 protocol and wireless section!!!!!!!!!

Can you give us some more details of this change?
Improve throughput / latency? It solves some stalemate?

Can we try it? If so, where is the download link?
some possible nv2 lockups/crash are fixed and also speed for the 802.11n might be more stable.

Contact support@mikrotik.com and we could allow you access for the development version section.
 
JanezFord
Member Candidate
Member Candidate
Posts: 264
Joined: Wed May 23, 2012 10:58 am

Re: What's new in 6.8rc1

Fri Jan 24, 2014 10:39 am

:D Realy good news! You've to clean code while integrating .ac
Or finishing off Wireless Controller
Which one would you prefer ?
Lets make a poll ... I vote for WLC ..

JF
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Fri Jan 24, 2014 11:41 am

*) wireless - improved 11n and nv2 stability;
Normis :shock: !!! Fantastic news!
You are working/improving NV2 protocol and wireless section!!!!!!!!!

Can you give us some more details of this change?
Improve throughput / latency? It solves some stalemate?

Can we try it? If so, where is the download link?
It is fix for this problem
http://forum.mikrotik.com/viewtopic.php ... nv2+lockup
LAN, FTTx, Wireless. ISP operator
 
User avatar
nz_monkey
Forum Guru
Forum Guru
Posts: 1825
Joined: Mon Jan 14, 2008 1:53 pm
Location: Straya
Contact:

Re: What's new in 6.8rc1

Fri Jan 24, 2014 11:58 am

:D Realy good news! You've to clean code while integrating .ac
Or finishing off Wireless Controller
Which one would you prefer ?
I vote WLC :)
http://thebrotherswisp.com/ | Mikrotik MTCNA, MTCRE, MTCINE | Fortinet FTCNA, FCNSP, FCT | Extreme Networks ENA
 
uldis
MikroTik Support
MikroTik Support
Posts: 3427
Joined: Mon May 31, 2004 2:55 pm

Re: What's new in 6.8rc1

Fri Jan 24, 2014 12:27 pm

*) wireless - improved 11n and nv2 stability;
Normis :shock: !!! Fantastic news!
You are working/improving NV2 protocol and wireless section!!!!!!!!!

Can you give us some more details of this change?
Improve throughput / latency? It solves some stalemate?

Can we try it? If so, where is the download link?
It is fix for this problem
http://forum.mikrotik.com/viewtopic.php ... nv2+lockup
Yes, that is fixed in this release.
 
hapi
Member Candidate
Member Candidate
Posts: 223
Joined: Fri Mar 11, 2011 11:21 am
Location: Czech Republic

Re: What's new in 6.8rc1

Fri Jan 24, 2014 12:45 pm

Everything was already promised in previous versions. When will it work in reality and I will be happy. When will it be released v6.8?
 
User avatar
kometchtech
Member Candidate
Member Candidate
Posts: 194
Joined: Sat Jun 15, 2013 4:25 am
Location: Japan
Contact:

Re: What's new in 6.8rc1

Fri Jan 24, 2014 1:32 pm

It is updated at 2014-01-24 08:58:53 with, Although it is daily build,
Why date of package contents has become a thing of yesterday are you?
--
Routerboard Users Group JP
http://www.rb-ug.jp/
CCR1009-8G-1S-1S+, RB750Gr3, CRS226-24G-2S+, RB850Gx2, RB960PGS, CRS317-1G-16S+,
RB2011UAS, CRS125-24G-1S, RB962UiGS-5HacT2HnT, CRS212-1G-10S-1S+, RB3011UiAS
 
barp21
just joined
Posts: 12
Joined: Tue Nov 16, 2010 11:09 pm

Re: What's new in 6.8rc1

Fri Jan 24, 2014 7:28 pm

What about problem with no country set? It is quite frustrating...
When quickset window isn’t closed and i log again to router using Winbox it automatically disconnect.
I notice in wireless setting options that instead of Poland it switch automatically to "no country set"
It happens on every SXT and SXT Lite since 6.1 version. Would be nice to have it fixed.
 
User avatar
payday
Member Candidate
Member Candidate
Posts: 233
Joined: Thu Aug 16, 2012 11:05 pm

Re: What's new in 6.8rc1

Fri Jan 24, 2014 7:38 pm

:D Realy good news! You've to clean code while integrating .ac
Or finishing off Wireless Controller
Which one would you prefer ?
I vote for WLC!
 
User avatar
samotoka
Frequent Visitor
Frequent Visitor
Posts: 86
Joined: Fri Aug 18, 2006 2:18 pm
Location: Hot Water Beach, New Zealand

Re: What's new in 6.8rc1

Fri Jan 24, 2014 9:32 pm

+1 for WLC
Proud owner of a RB2011UAS-2HnD-IN with ROS 6.19,
pc i586 2004 Mhz Athlon XP with ROS 3.30,
pc i586 330 Mhz Pentium II with ROS 3.30,
old pc 233 Mhz Cirix with ROS 2.9.27
 
mietus
Member Candidate
Member Candidate
Posts: 122
Joined: Mon Jan 30, 2006 11:14 pm
Location: Poland

Re: What's new in 6.8rc1

Fri Jan 24, 2014 10:01 pm

hmm, @MT what was added to latest build, file increased from 9,81 MB to 11,6 MB, it's some kind of surprise? ;-)
 
User avatar
nz_monkey
Forum Guru
Forum Guru
Posts: 1825
Joined: Mon Jan 14, 2008 1:53 pm
Location: Straya
Contact:

Re: What's new in 6.8rc1

Sat Jan 25, 2014 7:19 am

What's new in 6.8rc1 (2014-Jan-24 15:06):

*) bridge - default protocol-mode changed to RSTP for new bridges,
fixed bridge mac address changing when port (with lowest mac address) goes down
*) userman - improve startup time;
*) sstp client - support server name verification from certificate;
*) wireless - improved 11n and nv2 stability;
*) dhcp client - support interfaces in bridge;
*) dhcp - parse decimal strings and IP addreses in options value;
*) bgp - don't show community 'internet' in BGP advertisements;
*) ipsec - enable hardware acceleration for aes-cbc + md5|sha1|sha256 aead on tilera cpus;
*) ospf - fixed checksum calculation for OSPFv3 AS-external-LSAs;
*) default configuration - changed dhcp server lease time to 10 minutes;
*) fixed port isolation on CRSs (bug introduced in v6.6);
*) smb - added support for SMB 2.002
*) timezone information updated;
*) ppp - fixed ppp bridging (did not work since v6.6);
*) improved speed of PPP, PPPoE, PPTP & L2TP on multicore routers;
*) address-list - fix crash when adding two identical address list entries (not allowed any more);
*) fixed multicast forwarding on CCRs;
*) firewall - improved address-type matcher, and added it for ipv6 aswell;
http://thebrotherswisp.com/ | Mikrotik MTCNA, MTCRE, MTCINE | Fortinet FTCNA, FCNSP, FCT | Extreme Networks ENA
 
skibi82
newbie
Posts: 42
Joined: Fri Mar 22, 2013 7:09 pm

Re: What's new in 6.8rc1

Sat Jan 25, 2014 9:19 am

After one day of action rb951g hung wifi card.
routeros-mipsbe-6.8rc1 was updated at 2014-01-24 14:30

After restarting the communication device has been restored.
 
stavincki1
just joined
Posts: 12
Joined: Thu Jan 09, 2014 1:06 pm

Re: What's new in 6.8rc1

Sat Jan 25, 2014 11:29 am

Any news about IGMP proxy bugs?
 
ditonet
Forum Veteran
Forum Veteran
Posts: 841
Joined: Mon Oct 19, 2009 12:52 am
Location: Europe/Poland/Konstancin-Jeziorna
Contact:

Re: What's new in 6.8rc1

Sat Jan 25, 2014 2:05 pm

Did anyone noticed that latest mipsbe .npk file is bigger?
11.6MB instead of usual 9.8MB.
I'm very curious what made such difference.

Regards,
Grzegorz | MTCNA, MTCRE, MTCSE | konsultacje MikroTik Warszawa
It is a book about a Spanish guy called Manual. You should read it. - Dilbert
 
mietus
Member Candidate
Member Candidate
Posts: 122
Joined: Mon Jan 30, 2006 11:14 pm
Location: Poland

Re: What's new in 6.8rc1

Sat Jan 25, 2014 2:08 pm

Did anyone noticed that latest mipsbe .npk file is bigger?
11.6MB instead of usual 9.8MB.
I'm very curious what made such difference.

Regards,
eh.. look a bit above from your posts ;-)

I think it maybe some part of wlc.
 
ditonet
Forum Veteran
Forum Veteran
Posts: 841
Joined: Mon Oct 19, 2009 12:52 am
Location: Europe/Poland/Konstancin-Jeziorna
Contact:

Re: What's new in 6.8rc1

Sat Jan 25, 2014 2:25 pm

AFAIK 'WLC' will be a separated package.
I've compared separated package files,
only 'system-mipsbe.npk' is bigger than usually.

Regards,
Grzegorz | MTCNA, MTCRE, MTCSE | konsultacje MikroTik Warszawa
It is a book about a Spanish guy called Manual. You should read it. - Dilbert
 
efaden
Forum Guru
Forum Guru
Posts: 1711
Joined: Sat Mar 30, 2013 1:55 am
Location: New York, USA

Re: What's new in 6.8rc1

Sat Jan 25, 2014 5:52 pm

:D Realy good news! You've to clean code while integrating .ac
Or finishing off Wireless Controller
Which one would you prefer ?
I vote WLC :)
+1

Sent from my SCH-I545 using Tapatalk
 
mietus
Member Candidate
Member Candidate
Posts: 122
Joined: Mon Jan 30, 2006 11:14 pm
Location: Poland

Re: What's new in 6.8rc1

Sat Jan 25, 2014 10:19 pm

hmm

jan/02/1970 01:00:12 system,info installed routeros-mipsbe-6.8rc1
jan/02/1970 01:00:15 script,warning defconf: penta chains are only for 'ac' boards
jan/02/1970 01:00:30 interface,info ether1 link up (speed 100M, full duplex)

extra MB in .npk looks like initial support of new hardware ;)
 
leeajohnston
just joined
Posts: 3
Joined: Tue Oct 04, 2011 10:06 pm

Re: What's new in 6.8rc1

Sun Jan 26, 2014 3:08 pm

Hi,
Running 6.8rc1 (Jan/24/2014 15:06:50) on CCR1036-8G-2S+. I have connection tracking disabled, however if I create a firewall address list the contrack table starts filling (despite being disabled and not auto). I wouldn't have expected connection tracking to be required for an address list and this wasn't the behaviour in 6.7.
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Sun Jan 26, 2014 7:54 pm

jan/02/1970 01:00:12 system,info installed routeros-mipsbe-6.8rc1
jan/02/1970 01:00:15 script,warning defconf: penta chains are only for 'ac' boards
Nice :) what script do you use? It seems that we can on MUM enjoy the new AC Goodies
LAN, FTTx, Wireless. ISP operator
 
mietus
Member Candidate
Member Candidate
Posts: 122
Joined: Mon Jan 30, 2006 11:14 pm
Location: Poland

Re: What's new in 6.8rc1

Sun Jan 26, 2014 10:24 pm

jan/02/1970 01:00:12 system,info installed routeros-mipsbe-6.8rc1
jan/02/1970 01:00:15 script,warning defconf: penta chains are only for 'ac' boards
Nice :) what script do you use? It seems that we can on MUM enjoy the new AC Goodies
none, just upraded 911G board ;-)
 
uldis
MikroTik Support
MikroTik Support
Posts: 3427
Joined: Mon May 31, 2004 2:55 pm

Re: What's new in 6.8rc1

Mon Jan 27, 2014 10:08 am

After one day of action rb951g hung wifi card.
routeros-mipsbe-6.8rc1 was updated at 2014-01-24 14:30

After restarting the communication device has been restored.
Please tell us exactly what happens to the wireless interface - you couln't see it form the clients device, or no traffic was going? Disabling/enabling the wireless card didn't help?
Were you able to make support output file when the problem happened and sent to support@mikrotik.com?
 
ropeba
Member Candidate
Member Candidate
Posts: 220
Joined: Sat Jul 29, 2006 4:13 pm

Re: What's new in 6.8rc1

Mon Jan 27, 2014 3:01 pm

Any news about IGMP proxy bugs?
I want to know the same thing.
 
semenko
just joined
Posts: 14
Joined: Mon Feb 04, 2013 6:37 pm

Re: What's new in 6.8rc1

Mon Jan 27, 2014 9:03 pm

Is it now possible to disable DHCP options in the DHCP Client?

I can't remove hostname or clientid -- they keep coming back!

See ticket: 2014011766000899
You do not have the required permissions to view the files attached to this post.
 
skibi82
newbie
Posts: 42
Joined: Fri Mar 22, 2013 7:09 pm

Re: What's new in 6.8rc1

Tue Jan 28, 2014 8:11 am

Amendment to an earlier post on 6.8rc1 rb 951g router just hangs. In such a way that the internal watchdog nothing was done. There is no communication on any ports is also not on wifi. After the restart does not see normal speeds on the ports need to enable disable the port .

# Jan/28/2014 7: 4:25 to RouterOS 6.8rc1
# Software id = xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
#
jan/02/1970 1:00:15 interface , info v.p1.olkusz link up
jan/02/1970 1:00:15 interface , info v.p4.login link up
jan/02/1970 1:00:15 interface , info v.p2.nkt link up
jan/02/1970 1:00:15 interface , info v.p5.akwawit link up
jan/02/1970 1:00:15 interface , info v.MBIZ link up
jan/02/1970 1:00:20 interface , info e03.lan link up (speed 10M half duplex )
jan/02/1970 1:00:20 interface , info e02.lan link up (speed 10M half duplex )
jan/02/1970 1:00:20 interface , info e05.lan link up (speed 1000M , full duplex )
jan/02/1970 1:00:20 interface , info e04.lan link up (speed 1000M , full duplex )
jan/02/1970 1:00:20 wireless , debug w01 : 0:16 : EA : EE: 35:62 attempts is associate
jan/02/1970 1:00:20 wireless , debug w01 : 0:16 : EA : EE: 35:62 in local ACL , accept
jan/02/1970 1:00:20 wireless , info 0:16 : EA : EE: 35:62 @ w01 : connected
jan/02/1970 1:00:21 interface , info e05.lan link down
jan/02/1970 1:00:23 interface , info e05.lan link up (speed 1000M , full duplex )
jan/02/1970 1:00:32 interface , info e01.wan link up (speed 1000M , full duplex )
7:01:58 system , error , critical router was rebooted without proper shutdown
7:02:24 system , info, account user admin logged in from 192,168,254,110 via winbox
7:03:23 system , info device changed by admin
7:03:25 system , info device changed by admin
7:03:25 interface , info e03.lan link down
7:03:28 interface , info e03.lan link up (speed 10M half duplex )
7:03:32 system , info device changed by admin
7:03:42 system , info device changed by admin
7:03:43 interface , info e04.lan link down
7:03:46 interface , info e04.lan link up (speed 1000M , full duplex )
7:04:02 system , info, account user admin logged in from 192,168,254,110 via telnet

What to write on support. I'll write only when they solve the problems previously reported.
It has only to do downgrade
 
zyzelis
Member Candidate
Member Candidate
Posts: 213
Joined: Sun Apr 08, 2012 9:25 pm

Re: What's new in 6.8rc1

Tue Jan 28, 2014 10:11 am

Hello all,
despite that NV2 was fixed in 6.8rc1, i would not recommend to use this release with SXT 5nd r2, because ether1 port flapping issue.
 
User avatar
Chupaka
Forum Guru
Forum Guru
Posts: 8320
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: What's new in 6.8rc1

Tue Jan 28, 2014 12:24 pm

fixed bridge mac address changing when port (with lowest mac address) goes down
MT, please do the same for bonding =)
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
ste
Forum Guru
Forum Guru
Posts: 1815
Joined: Sun Feb 13, 2005 11:21 pm

Re: What's new in 6.8rc1

Tue Jan 28, 2014 1:15 pm

Hello all,
despite that NV2 was fixed in 6.8rc1, i would not recommend to use this release with SXT 5nd r2, because ether1 port flapping issue.
6.8rc1 is no release SW. Hope this is fixed for the release.

Seems MT has longer SW-Release cycles at the moment and makes more Betas for testing.

I would love to wait another month for 6.8 with all fixes included.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Tue Jan 28, 2014 1:21 pm

Hello all,
despite that NV2 was fixed in 6.8rc1, i would not recommend to use this release with SXT 5nd r2, because ether1 port flapping issue.
Please clarify what port flapping issue you mean, include your ticket number so I can check status. Thanks
No answer to your question? How to write posts
 
zyzelis
Member Candidate
Member Candidate
Posts: 213
Joined: Sun Apr 08, 2012 9:25 pm

Re: What's new in 6.8rc1

Tue Jan 28, 2014 3:07 pm

Hello all,
despite that NV2 was fixed in 6.8rc1, i would not recommend to use this release with SXT 5nd r2, because ether1 port flapping issue.
Please clarify what port flapping issue you mean, include your ticket number so I can check status. Thanks
labdien braliukai :)

Ok. lets try ;)
in short: after upgrade SXT 5ndr2 to 6.8rc1 randomly ether1 port goes down and up continuosly. it can be seen on pc connected to CPE. After downgrade to 6.7 flapping disappiers, but during speedtest, ether1 simply hangs (traffic isnt passing through ether1)
only way to restore ether1 - to reboot SXT.

now we are testing other cpe's to recreate same situation.

EDIT:
The Ticket ID is 2014012866000574
Last edited by zyzelis on Tue Jan 28, 2014 4:15 pm, edited 1 time in total.
 
zarmbiak80
just joined
Posts: 7
Joined: Thu Feb 03, 2011 3:38 pm

Re: What's new in 6.8rc1

Tue Jan 28, 2014 4:01 pm

SXT Lite 5ND r2 does not connect to acces point
SXT stops scanning on channel access point and stop, but not connecting
Disable, enable wlan1 solves the problem but not always
I checked various channel symptom of the same.
You do not have the required permissions to view the files attached to this post.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Tue Jan 28, 2014 4:02 pm

SXT Lite 5ND r2 does not connect to acces point
SXT stops scanning on channel access point and stop, but not connecting
Disable, enable wlan1 solves the problem but not always
I checked various channel symptom of the same.
what does the wireless,debug log say on both CPE and AP side when not connecting?
No answer to your question? How to write posts
 
zarmbiak80
just joined
Posts: 7
Joined: Thu Feb 03, 2011 3:38 pm

Re: What's new in 6.8rc1

Tue Jan 28, 2014 4:11 pm

SXT Lite 5ND r2 does not connect to acces point
SXT stops scanning on channel access point and stop, but not connecting
Disable, enable wlan1 solves the problem but not always
I checked various channel symptom of the same.
what does the wireless,debug log say on both CPE and AP side when not connecting?

Log on access point nothing shows
log on client station also clear
station connected when I disable anable wlan1
You do not have the required permissions to view the files attached to this post.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Tue Jan 28, 2014 4:15 pm

This is just Info log, please enable also Debug log (in system logging, add new topic with "wireless" and "debug")

Does this happen only one SXT lite, or also on other devices connected to the same AP?
No answer to your question? How to write posts
 
zarmbiak80
just joined
Posts: 7
Joined: Thu Feb 03, 2011 3:38 pm

Re: What's new in 6.8rc1

Tue Jan 28, 2014 4:21 pm

This is just Info log, please enable also Debug log (in system logging, add new topic with "wireless" and "debug")

Does this happen only one SXT lite, or also on other devices connected to the same AP?
Symptom has already performed at several sxt connected to different acces point
On the RB711 symptom does not occur
 
emboro
just joined
Posts: 4
Joined: Tue Jan 21, 2014 8:32 pm
Location: Poland

Re: What's new in 6.8rc1

Tue Jan 28, 2014 4:51 pm

I have the same problem as described above

i have made a support ticket#2014012366000654
 
petro25
Frequent Visitor
Frequent Visitor
Posts: 81
Joined: Sat Jul 24, 2010 10:49 pm
Location: Novosibirsk

Re: What's new in 6.8rc1

Tue Jan 28, 2014 5:17 pm

I confirm the problem. part 5 sxt r2 not connect to 20\40 if you are installing only 20 worked . part 5 sxt r2 didn't work at certain frequencies, for example in the range 5300-5320 not seen base. when changing frequencies on 5180 everything works. (we are talking about nv2).

I have 30 clients connected to the ap . when changing frequencies can connect the 20 to 25 clients a frequency on which all 30 clients. ether net to the nearest city-50 km
 
zyzelis
Member Candidate
Member Candidate
Posts: 213
Joined: Sun Apr 08, 2012 9:25 pm

Re: What's new in 6.8rc1

Tue Jan 28, 2014 5:41 pm

After upgrade OmniTik-UPA to 6.8 and firmware to 3.11, it died, after inspection on the site, we found port flapping.

EDIT
OmniTik even not loading from nand. And ticking :)

2nd edit

affected CPE SXT (6.8) still crashing under load (10/10Mbit udp btest) after 10s

going to netinstall
 
User avatar
honzam
Forum Guru
Forum Guru
Topic Author
Posts: 2297
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: What's new in 6.8rc1

Wed Jan 29, 2014 6:01 pm

affected CPE SXT (6.8) still crashing under load (10/10Mbit udp btest) after 10s
In V6.8 works fine. I tried BW test (10/10) 1minute. No crash
LAN, FTTx, Wireless. ISP operator
 
zyzelis
Member Candidate
Member Candidate
Posts: 213
Joined: Sun Apr 08, 2012 9:25 pm

Re: What's new in 6.8rc1

Wed Jan 29, 2014 7:19 pm

affected CPE SXT (6.8) still crashing under load (10/10Mbit udp btest) after 10s
In V6.8 works fine. I tried BW test (10/10) 1minute. No crash
Seems hw fault, because other devices works as expected.
 
biomesh
Member Candidate
Member Candidate
Posts: 139
Joined: Fri Feb 10, 2012 8:25 pm

Re: What's new in 6.8rc1

Wed Jan 29, 2014 9:28 pm

Dial on demand does not work on the RC that was released briefly this morning. A L2TP (and sstp) client that worked in previous releases (6.6 and earlier including 5.x) would not start. The interface did work if dial on demand was deactivated and was started manually.
 
emboro
just joined
Posts: 4
Joined: Tue Jan 21, 2014 8:32 pm
Location: Poland

Re: What's new in 6.8rc1

Thu Jan 30, 2014 4:24 pm

on ver. 6.8rc1 this problem still exists
although the network is aviable on scan RB SXT 5nD r2 canot connect to ap,
after reboot it can connect but not on every frequency.

log from SXT 5nD r2:
wireless,debug wlan1: no network that satisfies connect-list, by default choose with strongest signal
no log on ap

other clients working on RB SXT 5HPnD can conect to the same network with no problem on every frequency


Network conf.
cpe:
name="wlan1" mtu=1500 mac-address=D4:CA:6D:C1:63:59 arp=enabled
interface-type=Atheros AR9300 mode=station ssid="ssid"
frequency=5520 band=5ghz-a/n channel-width=20/40mhz-ht-above
scan-list=default wireless-protocol=nv2-nstreme-802.11 wds-mode=disabled
wds-default-bridge=none wds-ignore-ssid=no bridge-mode=enabled
default-authentication=yes default-forwarding=yes default-ap-tx-limit=0
default-client-tx-limit=0 hide-ssid=no security-profile=default
compression=no

ap:
name="wlan1" mtu=1500 mac-address=D4:CA:6D:10:A6:2C arp=enabled
interface-type=Atheros AR92xx mode=ap-bridge ssid="ssid"
frequency=5805 band=5ghz-onlyn channel-width=20/40mhz-ht-above
scan-list=default wireless-protocol=nv2 wds-mode=disabled
wds-default-bridge=none wds-ignore-ssid=no bridge-mode=enabled
default-authentication=yes default-forwarding=yes default-ap-tx-limit=0
default-client-tx-limit=0 hide-ssid=no security-profile=default
compression=no
 
emboro
just joined
Posts: 4
Joined: Tue Jan 21, 2014 8:32 pm
Location: Poland

Re: What's new in 6.8rc1

Thu Jan 30, 2014 4:27 pm

Dial on demand does not work on the RC that was released briefly this morning. A L2TP (and sstp) client that worked in previous releases (6.6 and earlier including 5.x) would not start. The interface did work if dial on demand was deactivated and was started manually.
i confirm that dial on demand dose not work
 
User avatar
sergejs
MikroTik Support
MikroTik Support
Posts: 6617
Joined: Thu Mar 31, 2005 3:33 pm
Location: Riga, Latvia
Contact:

Re: What's new in 6.8rc1

Thu Jan 30, 2014 5:27 pm

emboro, thank you very much for the report. We will try to fix this problem as soon as possible.
 
ffernandes
Member Candidate
Member Candidate
Posts: 146
Joined: Mon Jun 23, 2008 11:20 pm

Re: What's new in 6.8rc1

Thu Jan 30, 2014 8:08 pm

is it just me or 6.8 x86 using more ram then 6.7?
it doubled the used ram
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Fri Jan 31, 2014 12:24 pm

is it just me or 6.8 x86 using more ram then 6.7?
it doubled the used ram
What type of device you have? what features do you use?
No answer to your question? How to write posts
 
ffernandes
Member Candidate
Member Candidate
Posts: 146
Joined: Mon Jun 23, 2008 11:20 pm

Re: What's new in 6.8rc1

Fri Jan 31, 2014 12:56 pm

well normal x86 .. level4 routing my network...
nothing change since 6.7 only the increase of used ram, that doubled...

supout attached
You do not have the required permissions to view the files attached to this post.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Fri Jan 31, 2014 12:58 pm

Here is our X86 after upgrade to v6.9
Screenshot 2014-01-31 12.57.19.png
Please make one file after reboot (fresh start) and another after a while, when RAM is filled up. We will compare the two files, and will check what eats the memory in your device.
You do not have the required permissions to view the files attached to this post.
No answer to your question? How to write posts
 
ffernandes
Member Candidate
Member Candidate
Posts: 146
Joined: Mon Jun 23, 2008 11:20 pm

Re: What's new in 6.8rc1

Fri Jan 31, 2014 1:05 pm

graphing image
You do not have the required permissions to view the files attached to this post.
 
ffernandes
Member Candidate
Member Candidate
Posts: 146
Joined: Mon Jun 23, 2008 11:20 pm

Re: What's new in 6.8rc1

Fri Jan 31, 2014 1:14 pm

fresh start sup attach
You do not have the required permissions to view the files attached to this post.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24325
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: What's new in 6.8rc1

Fri Jan 31, 2014 1:16 pm

fresh start sup attach
this is a user forum, please send the files to support@mikrotik.com
No answer to your question? How to write posts
 
ffernandes
Member Candidate
Member Candidate
Posts: 146
Joined: Mon Jun 23, 2008 11:20 pm

Re: What's new in 6.8rc1

Fri Jan 31, 2014 1:25 pm

fresh start sup attach
this is a user forum, please send the files to support@mikrotik.com

wops... done :)

Who is online

Users browsing this forum: Google [Bot] and 111 guests