Community discussions

 
User avatar
Chupaka
Forum Guru
Forum Guru
Topic Author
Posts: 8319
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

v6.21 released!

Thu Oct 30, 2014 6:29 pm

What's new in 6.21 (2014-Oct-30 12:34):

*) userman - fix "Your session has been reset due to inactivity" error;
*) timezone - updated timezone information to 2014i release;
*) wireless - fixed scanning tool crash for 802.11ac interfaces
*) wireless - fixed Nv2 kernel panic on 802.11ac interfaces
*) quickset - added vpn configuration to Wifi AP %26 Ethernet modes as well;
*) lte - changed device identification for devices which regenerate MAC address,
most likely this will loose device's configuration;
*) sstp - fixed disconnects on high traffic load;
*) ovpn client - fixed problem where ip address was not added to bridge interface in ethernet mode;
*) webfig - show properly Switch Port configuration;
*) disks - fixed support for MMC/SD cards;
*) winbox - added filtering by dscp to torch;
*) certificate - fix CRL handling in trust chain;
*) fixed 6to4 tunnels having inactive routes;
*) ipsec - fix downgrade problem to v5;
*) ipsec - disallow template-policy-group=none in peer config and set it to 'default';
*) metarouter - some metaroutes didn't have their licenses;
*) torch - possibility to filter by dscp;
*) fixed - master port on AR8327 switches that is put into bridge could sometimes not work properly;
*) fixed queues - could have huge latencies and smaller throughput than specified;
*) interfaces report last link up/down time and link down count;

If you already run some RouterOS v6.x version, simply click “Check for updates” in QuickSet, Webfig or Winbox packages menu.

Others: http://www.mikrotik.com/download
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
User avatar
Chupaka
Forum Guru
Forum Guru
Topic Author
Posts: 8319
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: v6.21 released!

Thu Oct 30, 2014 6:34 pm

*) fixed queues - could have huge latencies and smaller throughput than specified;
guys, please comment on this change. what queues? in what conditions?
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
User avatar
honzam
Forum Guru
Forum Guru
Posts: 2294
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: v6.21 released!

Thu Oct 30, 2014 9:26 pm

*) interfaces report last link up/down time and link down count;
Any info about it? I can´t find it on SXT r2
LAN, FTTx, Wireless. ISP operator
 
User avatar
Chupaka
Forum Guru
Forum Guru
Topic Author
Posts: 8319
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: v6.21 released!

Thu Oct 30, 2014 10:17 pm

*) interfaces report last link up/down time and link down count;
Any info about it? I can´t find it on SXT r2
/interface print detail
<bla-bla-bla>
 4  R  name="vlan1321" type="vlan" mtu=1500 actual-mtu=1500 
       mac-address=00:00:00:00:00:01 fast-path=no 
       last-link-up-time=oct/30/2014 20:16:15 link-downs=0 
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
User avatar
Chupaka
Forum Guru
Forum Guru
Topic Author
Posts: 8319
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: v6.21 released!

Thu Oct 30, 2014 10:18 pm

*) fixed 6to4 tunnels having inactive routes;
by the way, not fixed for me :) "gateway=6to4tunnel" still doesn't work, route is not active
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24277
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

RouterOS v6.21

Fri Oct 31, 2014 10:16 am

What's new in 6.21 (2014-Oct-30 12:34):
*) userman - fix "Your session has been reset due to inactivity" error;
*) timezone - updated timezone information to 2014i release;
*) wireless - fixed scanning tool crash for 802.11ac interfaces
*) wireless - fixed Nv2 kernel panic on 802.11ac interfaces
*) quickset - added vpn configuration to Wifi AP %26 Ethernet modes as well;
*) lte - changed device identification for devices which regenerate MAC address,
most likely this will loose device's configuration;
*) sstp - fixed disconnects on high traffic load;
*) ovpn client - fixed problem where ip address was not added to bridge interface in ethernet mode;
*) webfig - show properly Switch Port configuration;
*) disks - fixed support for MMC/SD cards;
*) winbox - added filtering by dscp to torch;
*) certificate - fix CRL handling in trust chain;
*) fixed 6to4 tunnels having inactive routes;
*) ipsec - fix downgrade problem to v5;
*) ipsec - disallow template-policy-group=none in peer config and set it to 'default';
*) metarouter - some metaroutes didn't have their licenses;
*) torch - possibility to filter by dscp;
*) fixed - master port on AR8327 switches that is put into bridge could sometimes not work properly;
*) fixed queues - could have huge latencies and smaller throughput than specified;
*) interfaces report last link up/down time and link down count;
Simply click “Check for updates” in QuickSet, Webfig or Winbox packages menu.
No answer to your question? How to write posts
 
User avatar
honzam
Forum Guru
Forum Guru
Posts: 2294
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: RouterOS v6.21

Fri Oct 31, 2014 10:30 am

*) interfaces report last link up/down time and link down count;
Only in terminal?
LAN, FTTx, Wireless. ISP operator
 
Modestas
just joined
Posts: 18
Joined: Mon Jul 16, 2012 10:59 am
Location: Vilnius, Lithuania

Re: v6.21 released!

Fri Oct 31, 2014 10:47 am

What's new in 6.21 (2014-Oct-30 12:34):
If you already run some RouterOS v6.x version, simply click “Check for updates” in QuickSet, Webfig or Winbox packages menu.
Hi
Take care.
I've just upgraded my 450G to 6.21. Now box reboots right after starting services, gives not enough time to even enter password in CLI.
BR
Modestas
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24277
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: v6.21 released!

Fri Oct 31, 2014 10:55 am

What's new in 6.21 (2014-Oct-30 12:34):
If you already run some RouterOS v6.x version, simply click “Check for updates” in QuickSet, Webfig or Winbox packages menu.
Hi
Take care.
I've just upgraded my 450G to 6.21. Now box reboots right after starting services, gives not enough time to even enter password in CLI.
BR
Modestas
Please connect a serial cable and check what is written on the output before it reboots. Once you have copied this and emailed support, you can Netinstall the device with v6.21 to fix the reboot
No answer to your question? How to write posts
 
User avatar
Chupaka
Forum Guru
Forum Guru
Topic Author
Posts: 8319
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: RouterOS v6.21

Fri Oct 31, 2014 10:58 am

*) fixed queues - could have huge latencies and smaller throughput than specified;
Normis, please comment on this change... we need more details :)
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
Modestas
just joined
Posts: 18
Joined: Mon Jul 16, 2012 10:59 am
Location: Vilnius, Lithuania

Re: v6.21 released!

Fri Oct 31, 2014 11:12 am

What's new in 6.21 (2014-Oct-30 12:34):
If you already run some RouterOS v6.x version, simply click “Check for updates” in QuickSet, Webfig or Winbox packages menu.
Hi
Take care.
I've just upgraded my 450G to 6.21. Now box reboots right after starting services, gives not enough time to even enter password in CLI.
BR
Modestas
Please connect a serial cable and check what is written on the output before it reboots. Once you have copied this and emailed support, you can Netinstall the device with v6.21 to fix the reboot
Hi
There are no specific messages before reboot (see CLI output below). Device just issues double beep and restarts
RouterBOOT booter 3.18

RouterBoard 450G

CPU frequency: 680 MHz
Memory size: 256 MiB
NAND size: 512 MiB

Press any key within 2 seconds to enter setup..

loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
Starting...


RouterBOOT booter 3.18

RouterBoard 450G

CPU frequency: 680 MHz
Memory size: 256 MiB
NAND size: 512 MiB

Press any key within 2 seconds to enter setup..

loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code

Starting...
Starting services...



MikroTik Login: admin
Password:


RouterBOOT booter 3.18

RouterBoard 450G

CPU frequency: 680 MHz


Thank you for suggestion to try netinstall.

BR
Modestas
 
User avatar
CyberTod
Long time Member
Long time Member
Posts: 511
Joined: Wed Jan 25, 2012 10:23 am

Re: v6.21 released!

Fri Oct 31, 2014 11:21 am

*) interfaces report last link up/down time and link down count;
Excellent addition. But it is visible only in terminal and the time shown does not account for timezone.\
linkup.jpg
You do not have the required permissions to view the files attached to this post.
 
User avatar
nz_monkey
Forum Guru
Forum Guru
Posts: 1821
Joined: Mon Jan 14, 2008 1:53 pm
Location: Straya
Contact:

Re: v6.21 released!

Fri Oct 31, 2014 11:33 am

*) interfaces report last link up/down time and link down count;
A huge Thank You to Mikrotik! This feature is very useful.

This is currently CLI only via "/interface print detail" and works for all interface types.

It will be in WinBox from 6.22
http://thebrotherswisp.com/ | Mikrotik MTCNA, MTCRE, MTCINE | Fortinet FTCNA, FCNSP, FCT | Extreme Networks ENA
 
gnuttisch
Member
Member
Posts: 309
Joined: Fri Sep 10, 2010 3:49 pm

Re: RouterOS v6.21

Fri Oct 31, 2014 12:30 pm

I have updated a RB493 and a RB951G-2HnD and went well.

I have some ptp-links whit NV2 still running on 5.26. Is their any ideas to upgrade them to 6.21 also? or are the wireless changes in 6.xx only for the bugs that have been released in 6.xx =)
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24277
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RouterOS v6.21

Fri Oct 31, 2014 1:41 pm

modestas

please let us know if netinstall helped. also, what configuration did you have there? which version did you upgrade from?
No answer to your question? How to write posts
 
User avatar
noyo
Member Candidate
Member Candidate
Posts: 114
Joined: Sat Jan 28, 2012 12:25 am
Location: Mazury - Poland
Contact:

Re: RouterOS v6.21

Fri Oct 31, 2014 1:50 pm

after upgrading v5.26 --> v.6.21 :(
http://kazuko.pl/pryw/31102014185.mp4
thanks mikrotik
 
PastuhMedvedey
newbie
Posts: 40
Joined: Fri Jan 13, 2012 1:42 pm
Location: Ukraine

Re: RouterOS v6.21

Fri Oct 31, 2014 2:08 pm

After updating the device RB SXT G-2Hnd with 5.20 to 6.21, the device stopped working. Rebooting does not help.
RB751U-2HnD, RB2011LS, RB1100AH, RB433, RB411GL, RBSXT, CCR1016
 
bommi
just joined
Posts: 24
Joined: Fri Jan 24, 2014 9:13 am
Location: Germany
Contact:

Re: RouterOS v6.21

Fri Oct 31, 2014 2:16 pm

There is also an firmware update for my 951G-2HnD to version 3.19.
Any news what has changed?

This site has not yet been updated:
http://wiki.mikrotik.com/wiki/RouterBOOT_changelog
 
cmoegele
newbie
Posts: 35
Joined: Tue Nov 29, 2011 7:44 pm

Re: RouterOS v6.21

Fri Oct 31, 2014 2:39 pm

After updating the device RB SXT G-2Hnd with 5.20 to 6.21, the device stopped working. Rebooting does not help.
m8 is this senseful? Are you upgrading XP directly to Win8.1 ?
Even an upgrade from 5.26 ( with new firmware) could have some risks, ....
With netflash you will get your device back to work.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24277
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RouterOS v6.21

Fri Oct 31, 2014 2:49 pm

Until further notice, please refrain from upgrading if you are running v5.x
We have found something and are investigating. Upgrades from v6.x seem to be working fine though
No answer to your question? How to write posts
 
PastuhMedvedey
newbie
Posts: 40
Joined: Fri Jan 13, 2012 1:42 pm
Location: Ukraine

Re: RouterOS v6.21

Fri Oct 31, 2014 2:53 pm

Even an upgrade from 5.26 ( with new firmware) could have some risks, ....
With netflash you will get your device back to work.
Thank you. Netinstall restore operation.
RB751U-2HnD, RB2011LS, RB1100AH, RB433, RB411GL, RBSXT, CCR1016
 
PastuhMedvedey
newbie
Posts: 40
Joined: Fri Jan 13, 2012 1:42 pm
Location: Ukraine

Re: RouterOS v6.21

Fri Oct 31, 2014 2:57 pm

Upgrades from v6.x seem to be working fine though
Upgrading from 6.x to 6.21, without problems. Thank you.
RB751U-2HnD, RB2011LS, RB1100AH, RB433, RB411GL, RBSXT, CCR1016
 
napismizpravu
Member Candidate
Member Candidate
Posts: 135
Joined: Sat Apr 09, 2011 1:27 pm
Location: czech

Re: RouterOS v6.21

Fri Oct 31, 2014 3:08 pm

RB433UAH

upgrade 6.2x >6.22rc3

again error USB Flash disk problem + proxy

http://forum.mikrotik.com/viewtopic.php ... 78#p454175
 
User avatar
apteixeira
Trainer
Trainer
Posts: 50
Joined: Fri Oct 05, 2012 5:54 pm

Re: RouterOS v6.21

Fri Oct 31, 2014 3:20 pm

Hello,

CRL error persists: "OpenVPN Server error: TLS failed".

Previous post: http://forum.mikrotik.com/viewtopic.php?f=2&t=88372

I tested with several certificates: issued by GoDaddy, CACert and using OpenSSL. If you create then without CRL the connection established correctly.

Here are some images:

Image

Image

Best regads.
 
User avatar
Chupaka
Forum Guru
Forum Guru
Topic Author
Posts: 8319
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: RouterOS v6.21

Fri Oct 31, 2014 3:50 pm

I saw someone already wrote something like this, but without red color :)

WARNING!

do NOT use "/system ntp client set servers-dns-names=" together with static DNS servers - your router won't boot next time, you will need to reset configuration

tested on our production CCR...
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24277
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RouterOS v6.21

Fri Oct 31, 2014 4:01 pm

We have removed v6.21 from the webpage until the upgrade issue is fixed. It is caused by different disk management in new v6.21
No answer to your question? How to write posts

Who is online

Users browsing this forum: Bing [Bot], MSN [Bot] and 50 guests