Community discussions

  • 1
  • 4
  • 5
  • 6
  • 7
  • 8
  • 11
 
User avatar
TomjNorthIdaho
Forum Veteran
Forum Veteran
Posts: 979
Joined: Mon Oct 04, 2010 11:25 pm
Location: North Idaho
Contact:

6.35rc21 - ugly - took down the whole network !!!

Wed Mar 09, 2016 2:15 am

Today 3/8/2016 I tested 6.35rc21 with the new wireless package on my DynaDish WDS client. That was a mistake.

This took down my network almost everywhere... The problem went through almost all of my other cisco switches and other networks...

My DynaDish was an 802.11 AC 80 MHz wide WDS link in client-Mode , - which was also passing vlan traffic. I could no longer talk to the either DynaDish over wireless or Ethernet.
It also took out the DynaDish WDS AP running 6.34.2 wireless-cm2 . To get back into the WDS AP using my Ethernet connection, we had to face the WDS AP away from the WDS client so that it was no longer registered - then I could get into the WDS AP running the non RC firmware.

So at this time, I have a remote DynaDish WDS client on the RC firmware and I can not get into it using wireless or the Ethernet. The Ethernet does not even show a link.

Good thing I had other alternate links between my two locations.

Has anybody else encountered this ?

North Idaho Tom Jones
 
yottabit
Member Candidate
Member Candidate
Posts: 160
Joined: Thu Feb 21, 2013 5:56 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 2:21 am

Connection to non-Mikrotik and still use one radio for station and AP modes simultaneously.
 
User avatar
Alessio Garavano
Member
Member
Posts: 304
Joined: Sat May 29, 2004 12:49 am
Location: Corrientes, Argentina
Contact:

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 2:34 am

Connection to non-Mikrotik and still use one radio for station and AP modes simultaneously.
This i know... but has another advantage over WDS in performance or something connecting 2 RB in repeater mode?
Alessio Garavano
http://www.isparg.com.ar
 
yottabit
Member Candidate
Member Candidate
Posts: 160
Joined: Thu Feb 21, 2013 5:56 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 2:55 am

No, probably a disadvantage in performance and/or reliability, actually. Specifically this breaks layer-2 since you can't bridge multiple MAC addresses across station mode per 802.11 spec. So you end up using Station Pseudobridge mode which does a sort of NAT for MAC addresses. WDS avoids all that mess.
 
jondavy
Member Candidate
Member Candidate
Posts: 124
Joined: Tue May 12, 2009 11:14 pm
Location: Brasil

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 3:00 am

please define as default this option in OmniTik and other RouterBards

/interface ethernet poe settings set ether1-poe-in-long-cable=yes

because the outputs PoE outs do not work if not activated this function,
because many find it defective.
 
raffav
Member Candidate
Member Candidate
Posts: 278
Joined: Wed Oct 24, 2012 4:40 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 7:50 am

ATTENTION
KERNEL BOOT LOOP ON RC21
On rb433 with wireless rep packege kernel boot,
If wifi-rep disable or switched to wifi-cm2 kernel ok
On crs125 all ok
 
benoga
just joined
Posts: 13
Joined: Wed Mar 09, 2016 7:50 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 7:56 am

I use CCR1009 and HAP AC (CapsMan) and have with HAP AC boot loop (6.35.17 and 6.35.21). When i disable CapsMan, then works fine.

(Version 6.35.19 works fine for the HAP AC)

CCR never boot loop, only HAP AC
 
User avatar
strods
MikroTik Support
MikroTik Support
Posts: 1406
Joined: Wed Jul 16, 2014 7:22 am
Location: Riga, Latvia

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 9:37 am

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.

If router goes into reboot loop, then if device has serial port send output of it within text file to support.

If router is rebooting and it does not have serial port, then Netinstall it to older version (With "Keep old configuration" enabled on Netinstall), generate supout file and send it to us.
 
raffav
Member Candidate
Member Candidate
Posts: 278
Joined: Wed Oct 24, 2012 4:40 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 1:05 pm

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.

If router goes into reboot loop, then if device has serial port send output of it within text file to support.

If router is rebooting and it does not have serial port, then Netinstall it to older version (With "Keep old configuration" enabled on Netinstall), generate supout file and send it to us.
On my rb433uah after update to rc21 rb was rebooting after 5-10 seconds after system boot normally
In this middle time a was able to login and try to find the cause since in early rc a got the same kernel boot failure I disable de capsman, but not resolved
So i decided to disable the wifi-rep package after some try and ninja moves I finally got the packege to disable and the problem was gone.

The problem is this crashes didn't made autosupport files
And now the crazy
I had decided to turn wifi-rep again
The result no kernel failure :shock: :shock:
How I can sent the support file since now the rb looks ok?
 
notToNew
Member Candidate
Member Candidate
Posts: 146
Joined: Fri Feb 19, 2016 3:15 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 2:09 pm

Had the same on 952Ui-5ac2nD. Downgraded to rc19 and it is stable again.
--------------------------------------------------------------------------------------------
CCR1036-12G-4S, several 952Ui-5ac2nD, ...
 
linek1980
newbie
Posts: 34
Joined: Thu Feb 03, 2011 1:39 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 4:25 pm

RB433AH + wireless-rep-6.35rc21 = KERNEL BOOT LOOP. Rescue : telnet short time between the start and reboot interface wireless disable
 
kristaps
Member Candidate
Member Candidate
Posts: 272
Joined: Mon Jan 27, 2014 1:37 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 5:28 pm

linek1980 what wireless card are you running ?
http://routerboard.com/R52NM aka AR92xxx
or http://routerboard.com/R52H aka AR5xxx
 
raffav
Member Candidate
Member Candidate
Posts: 278
Joined: Wed Oct 24, 2012 4:40 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 5:43 pm

i think that the kernel boot loop is related to wifi-rep on the 433 or related to wireless card
because at home i use a 433uah as capsman and there was no cap enable on it and also get the kernel boot
i fallback to wifi-cm2 and the problem is gone, with cap enable
i my case the wifi card is a xr2 on both device
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 6:04 pm

i think that the kernel boot loop is related to wifi-rep on the 433 or related to wireless card
because at home i use a 433uah as capsman and there was no cap enable on it and also get the kernel boot
i fallback to wifi-cm2 and the problem is gone, with cap enable
i my case the wifi card is a xr2 on both device
Please provide support output file to support@mikrotik.com after you are able to recover the board by disabling the wireless card. That will help us to identify the problem and fix it.
 
yottabit
Member Candidate
Member Candidate
Posts: 160
Joined: Thu Feb 21, 2013 5:56 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 6:27 pm

Running rc21 just now on rb962 (hAP ac). I started with a blank config and ended up in a boot loop:
  • Changed wlan1 (2 GHz) to station pseudobridge
  • Scanned
  • Chose a network
  • Clicked connect
  • Appeared to start connecting and then the router rebooted and got stuck in a boot loop.
I had to clear the config. After clearing, I tried again and the same thing happened.

Cleared again, and used it to successfully connect to a different network.

Without console access, how can I get a kernel panic message and/or kernel dump? What would you like to see?
I forgot to note in my post that I was using wireless-rep package.

I don't have access to that router anymore, but when my new ones arrive today I'll reproduce and get a supout.
 
raffav
Member Candidate
Member Candidate
Posts: 278
Joined: Wed Oct 24, 2012 4:40 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 7:03 pm

i think that the kernel boot loop is related to wifi-rep on the 433 or related to wireless card
because at home i use a 433uah as capsman and there was no cap enable on it and also get the kernel boot
i fallback to wifi-cm2 and the problem is gone, with cap enable
i my case the wifi card is a xr2 on both device
Please provide support output file to support@mikrotik.com after you are able to recover the board by disabling the wireless card. That will help us to identify the problem and fix it.

i had already sent
Ticket#2016030966000791
 
PeterDoBrasil
Member Candidate
Member Candidate
Posts: 134
Joined: Sun Aug 23, 2015 6:55 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 10:29 pm

v6.35rc21
after upgrade sxt Light lost access to device, device are reboot every 60 seconds, after downgrade to v.6.35rc19 no more problems, I think there is any thing with ether port configuration causing this problem. The unice option to access the device is reset with reset button, and then downgrade to v6.35rc19 :?
 
PeterDoBrasil
Member Candidate
Member Candidate
Posts: 134
Joined: Sun Aug 23, 2015 6:55 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 10:30 pm

v6.35rc21
after upgrade sxt Light lost access to device, device reboots every 60 seconds, after downgrade to v.6.35rc19 no more problems, I think there is any thing with ether port configuration causing this problem. The unice option to access the device is reset with reset button, and then downgrade to v6.35rc19 :?
 
raffav
Member Candidate
Member Candidate
Posts: 278
Joined: Wed Oct 24, 2012 4:40 am

Re: v6.35rc [release candidate] is released, new wireless package!

Wed Mar 09, 2016 10:50 pm

v6.35rc21
after upgrade sxt Light lost access to device, device reboots every 60 seconds, after downgrade to v.6.35rc19 no more problems, I think there is any thing with ether port configuration causing this problem. The unice option to access the device is reset with reset button, and then downgrade to v6.35rc19 :?

disable the wifi-rep and enable the wifi-cm2 and that will work
 
Naurislv
newbie
Posts: 47
Joined: Tue May 06, 2014 11:29 am

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 9:37 am

We have implemented fix which should help with wireless-rep reboot loop. Please test it if you can use rc version on your environment. Fix will be available in RouterOS v6.35rc25.
 
User avatar
strods
MikroTik Support
MikroTik Support
Posts: 1406
Joined: Wed Jul 16, 2014 7:22 am
Location: Riga, Latvia

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 11:32 am

Version 6.35rc25 has been released.

Changes since previous version:

*) tile - fixed rare situation when some cores decide not to take part in packet processing till next reboot;
*) fastpath - fixed crash when packet arrives on disabled interface;
*) capsman - fixed capsman extension channel names;
*) console - fixed print follow in "/ip dns cache" menu
*) ethernet - add option to see S-GPON-ONU module, GPON side SN in "/int eth mon sfp#"
*) ethernet - do not allow to set self as master port;
*) health - always report fan speed (even if it is 0);
*) l2tp - introduced per tunnel allow-fast-path option;
*) webfig - fixed firewall rule sorting did not work in other chains except all;
*) winbox - allow to set multiple dh-groups;
*) winbox - do not show fan statuses in passive cooling CCR1009;
*) winbox - fixed unset options in /routing ospf interface menu;
*) wireless-rep - fix crash on non-HT clients;
*) l2tp - implemented l2tp and lns fastpath/fasttrack support;
*) pppoe-client - implemented fastpath support.

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.
 
mistry7
Forum Guru
Forum Guru
Posts: 1244
Joined: Tue Oct 13, 2009 11:57 am
Location: Germany

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 11:59 am

Version 6.35rc25 has been released.

Changes since previous version:

*) tile - fixed rare situation when some cores decide not to take part in packet processing till next reboot;
*) fastpath - fixed crash when packet arrives on disabled interface;
*) capsman - fixed capsman extension channel names;
*) console - fixed print follow in "/ip dns cache" menu
*) ethernet - add option to see S-GPON-ONU module, GPON side SN in "/int eth mon sfp#"
*) ethernet - do not allow to set self as master port;
*) health - always report fan speed (even if it is 0);
*) l2tp - introduced per tunnel allow-fast-path option;
*) webfig - fixed firewall rule sorting did not work in other chains except all;
*) winbox - allow to set multiple dh-groups;
*) winbox - do not show fan statuses in passive cooling CCR1009;
*) winbox - fixed unset options in /routing ospf interface menu;
*) wireless-rep - fix crash on non-HT clients;
*) l2tp - implemented l2tp and lns fastpath/fasttrack support;
*) pppoe-client - implemented fastpath support.

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.

When i Download and Install 6.35 RC25
My CRS reboot with Kernel Failure
I now use 6.35 RC21
it creates autosupot
 
User avatar
strods
MikroTik Support
MikroTik Support
Posts: 1406
Joined: Wed Jul 16, 2014 7:22 am
Location: Riga, Latvia

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 12:02 pm

mistry7 - Did it actually upgrade? Or did it boot up with rc21?
 
anuser
Member
Member
Posts: 369
Joined: Sat Nov 29, 2014 7:27 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 12:07 pm

Bug or missing feature in new wireless package?

setup: traffic forwarding @CAPSMAN controller:

- with wireless-fp: client receives IPv6 router advertisement, everything works
- with wireless-rep: client doesn´t receive any IPv6 traffic, no RA at all

(I use the same configuration, just disable/enable wireless-fp/wireless-rep package on both CAPSMAN controller and CAP, also tested with 6.35rc25 on x86)
MikroTik ticket: 2016031066000617
Last edited by anuser on Thu Mar 10, 2016 12:46 pm, edited 2 times in total.
 
andriys
Forum Guru
Forum Guru
Posts: 1115
Joined: Thu Nov 24, 2011 1:59 pm
Location: Kharkiv, Ukraine

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 12:34 pm

- with wireless-fp: client receives IPv6 router advertisement, everything works
- with wireless-rep: client doesn´t receive any IPv6 traffic, no RA at all
Have you switch from wireless-fp to wireless-rep on both CAP (access point) and CAPsMAN (controller)? The wireless-fp implements CAPsMAN v1 while wireless-rep implements CAPsMAN v2 and these are not compatible with each other.
 
anuser
Member
Member
Posts: 369
Joined: Sat Nov 29, 2014 7:27 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 12:46 pm

- with wireless-fp: client receives IPv6 router advertisement, everything works
- with wireless-rep: client doesn´t receive any IPv6 traffic, no RA at all
Have you switch from wireless-fp to wireless-rep on both CAP (access point) and CAPsMAN (controller)? The wireless-fp implements CAPsMAN v1 while wireless-rep implements CAPsMAN v2 and these are not compatible with each other.
Yes I did and realized that I made a mistake.

The Problem is: with CAPsMANv2 and „wireless-rep“ package clients don´t receive any IPv6 traffic, no IPv6 router adverisements at all iff VLAN assignement is done dynamically. Dynamic VLAN assignment within datapath works for IPv4 traffic, though. If I assign a VLAN ID wihin datapath configuration of CAPSMAN, IPv6 and IPv4 is working without any problems.

(with traffic forwarding @CAPSMAN controller)

[UPDATE]

+ It works when I change multicast-helper setting to full on the Cap interface
Last edited by anuser on Mon Mar 14, 2016 2:19 pm, edited 2 times in total.
 
mistry7
Forum Guru
Forum Guru
Posts: 1244
Joined: Tue Oct 13, 2009 11:57 am
Location: Germany

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 1:23 pm

mistry7 - Did it actually upgrade? Or did it boot up with rc21?

upgrade
 
mccreigh
just joined
Posts: 8
Joined: Sun Apr 27, 2014 9:01 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 2:38 pm

I installed the v6.35rc21 firmware bundle and matching wireless-rep in a RBmAP-2nD access point (1 Ethernet, 1 2.4GHz wireless). I tried the new wireless repeater mode, which uses the one physical wireless interface as a station virtual interface bridged to an access point virtual interface, and it seems to work.

There's one last bit of wireless-to-wireless functionality in consumer travel routers that should now be possible with RouterOS, but I haven't yet seen how. Consider the "Hotspot mode" of the ASUS WL-330N3G travel router. It implements two virtual wireless interfaces on the same physical interface. On its station virtual interface it has a DHCP client and obtains a single IP address. Its Ethernet physical interface and access point virtual interface bridge onto a LAN with a DHCP server, which NATs through the IP address of the station interface. Its access point virtual interface is generally configured with a different SSID and different link security than its station virtual interface.

This mode lets you create a private encrypted wireless LAN in your hotel room so you can use unencrypted protocols among your wireless devices without worrying about other hotel guests being able to see them, even if the hotel's own guest wireless network is unencrypted.

Can this now be done with RouterOS v6.35 including wireless-rep? If so, could someone please explain how?
 
yottabit
Member Candidate
Member Candidate
Posts: 160
Joined: Thu Feb 21, 2013 5:56 am

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 3:11 pm

Yes it can. Change wlan1 to station pseudobridge, connect it to a Wi-Fi network by using the scan function. (Remember to setup a security profile if needed for Wi-Fi encryption.) Then setup firewall to src NAT that interface. Create a Virtual AP on the same interface. Ensure both wlan1 and the Virtual AP are joined to a bridge interface. Turn on DHCP server. Should be close to finished. I can send you a working config later if you get stuck.
 
blimbach
just joined
Posts: 8
Joined: Fri Mar 04, 2016 3:39 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 4:41 pm

I´ve tried to upgrade my "hap lite" (smips) from rc21 with wireless-rep to rc25 via winbox: System -> Packages.

This doesn´t work with the following error:

ERROR: not enough disk space, 7.7MiB is required and only 7.1 MiB is free.
 
yottabit
Member Candidate
Member Candidate
Posts: 160
Joined: Thu Feb 21, 2013 5:56 am

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 4:44 pm

I´ve tried to upgrade my "hap lite" (smips) from rc21 with wireless-rep to rc25 via winbox: System -> Packages.

This doesn´t work with the following error:

ERROR: not enough disk space, 7.7MiB is required and only 7.1 MiB is free.
Have you tried from a fresh boot (i.e., empty ramdisk)?

If it still doesn't work, can you delete one of the wireless packages you no longer need, e.g., wireless-fp and/or wireless-cm2?
 
blimbach
just joined
Posts: 8
Joined: Fri Mar 04, 2016 3:39 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 4:59 pm

Thank for the hint yottabit, but it doesn´t work.

It says: Can´t uninstall bundled packages (wireless-cm2 / wireless-fp). Also System-Recources tells me that 40MB RAM are free. It´s only a small CAP i´m testing.
 
jarda
Forum Guru
Forum Guru
Posts: 7601
Joined: Mon Oct 22, 2012 4:46 pm

Thu Mar 10, 2016 5:02 pm

Blimbach, you should read from the beginning. Or at least from here...


http://forum.mikrotik.com/viewtopic.php ... 78#p522278
 
Sob
Forum Guru
Forum Guru
Posts: 4410
Joined: Mon Apr 20, 2009 9:11 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 5:27 pm

..., install system package only, ...
Stupid question: Is this specific to smips where packages are smaller and just system one would probably fit in free space (I don't have any smips device myself, so I can't say for sure), or is there a way (without netinstall), how to do it for mipsbe too? I wanted to get rid of combined package on my mAP Lite and free space was only around 5MB, while system package is almost 7MB.
People who quote full posts should be spanked with ethernet cable. Some exceptions for multi-topic threads may apply.
 
nkourtzis
Member Candidate
Member Candidate
Posts: 202
Joined: Tue Dec 11, 2012 12:56 am
Location: Greece

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 5:57 pm

When i Download and Install 6.35 RC25
My CRS reboot with Kernel Failure
I now use 6.35 RC21
it creates autosupot
Same here, upgrading a hEX Lite board from RC19. Upgrade fails. Opened support ticket (#2016031066001081).
Passionate about networks
Enthusiastic about Mikrotik
MTCNA | MTCRE | MTCINE

No trees were killed to send this message,
but a large number of electrons were terribly inconvenienced.
 
mccreigh
just joined
Posts: 8
Joined: Sun Apr 27, 2014 9:01 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 6:19 pm

Yes it can. Change wlan1 to station pseudobridge, connect it to a Wi-Fi network by using the scan function. (Remember to setup a security profile if needed for Wi-Fi encryption.) Then setup firewall to src NAT that interface. Create a Virtual AP on the same interface. Ensure both wlan1 and the Virtual AP are joined to a bridge interface. Turn on DHCP server. Should be close to finished. I can send you a working config later if you get stuck.
I'd really appreciate a working config that I can dig through to understand.

My other problem is finding a sequence of steps to get from the factory-default RBmAPL-n2D WISP AP configuration to one where the (only) Ethernet interface is on the LAN without losing Winbox connectability. (I can always use the magic button to restore the factory-default configuration, but then I'm right back where I started.) Once I'm controlling the router firmly through its Ethernet interface, I should be able to reconfigure the wlan interface without losing control.
 
raffav
Member Candidate
Member Candidate
Posts: 278
Joined: Wed Oct 24, 2012 4:40 am

Re: v6.35rc [release candidate] is released, new wireless package!

Thu Mar 10, 2016 11:03 pm

ATTENTION
RC26
Maybe constant reboot on CHR
verifying if is a isolated case or on all CHR
testing on another CHR
ignore, it was a isolated case !!!
 
mistry7
Forum Guru
Forum Guru
Posts: 1244
Joined: Tue Oct 13, 2009 11:57 am
Location: Germany

Re: v6.35rc [release candidate] is released, new wireless package!

Fri Mar 11, 2016 1:30 pm

mistry7 - Did it actually upgrade? Or did it boot up with rc21?

with RC26 upgrade works
 
raffav
Member Candidate
Member Candidate
Posts: 278
Joined: Wed Oct 24, 2012 4:40 am

Re: v6.35rc [release candidate] is released, new wireless package!

Fri Mar 11, 2016 5:34 pm

I am getting reboot on CHR
12:08:22 system,error,critical router was rebooted without proper shutdown
when CAPMAN is enable on any wifi pack CM2 or REP
 
mccreigh
just joined
Posts: 8
Joined: Sun Apr 27, 2014 9:01 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Fri Mar 11, 2016 7:45 pm

Yes it can. Change wlan1 to station pseudobridge, connect it to a Wi-Fi network by using the scan function. (Remember to setup a security profile if needed for Wi-Fi encryption.) Then setup firewall to src NAT that interface. Create a Virtual AP on the same interface. Ensure both wlan1 and the Virtual AP are joined to a bridge interface. Turn on DHCP server. Should be close to finished. I can send you a working config later if you get stuck.
I'd really appreciate a working config that I can dig through to understand.

My other problem is finding a sequence of steps to get from the factory-default RBmAPL-n2D WISP AP configuration to one where the (only) Ethernet interface is on the LAN without losing Winbox connectability. (I can always use the magic button to restore the factory-default configuration, but then I'm right back where I started.) Once I'm controlling the router firmly through its Ethernet interface, I should be able to reconfigure the wlan interface without losing control.
Recall that we're discussing a RBmAPL-2nD single-Ethernet single-WAN router, where I wanted to use an existing WLAN as my WAN, and NAT-route it to a LAN consisting of an access point (using the same WiFi radio) with a different SSID and the Ethernet. I hoped that RouterOS v6.35 might at last allow me to do that in a single box. It's working now, thanks to yottabit's vital hints. His one hint that confused me a bit was "ensure that wlan1 and the Virtual AP are joined to a bridge interface". I think he meant that ether1 and the Virtual AP should be joined to a bridge interface. If anybody wants the config, I'll post it.
 
PeterDoBrasil
Member Candidate
Member Candidate
Posts: 134
Joined: Sun Aug 23, 2015 6:55 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Sat Mar 12, 2016 2:25 am

We have implemented fix which should help with wireless-rep reboot loop. Please test it if you can use rc version on your environment. Fix will be available in RouterOS v6.35rc25.
Thank you, Iám using v6.35rc26; no more problems! :lol:
 
incahex
just joined
Posts: 5
Joined: Fri Mar 04, 2016 11:05 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Sat Mar 12, 2016 6:09 pm

Rc26
My hex increases the use of mem whitout reason until it hangs. Need to reboot to work again and do the same again.
12 hours more or less until it uses all the memory and need reboot.

No config changes before update. Only from rc 19 to rc 26

Update to include image.
Image
 
PeterDoBrasil
Member Candidate
Member Candidate
Posts: 134
Joined: Sun Aug 23, 2015 6:55 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Sat Mar 12, 2016 8:33 pm

Mikrotik will launch how much rc's to come to final version ???? 30? 40? 50?
 
nkourtzis
Member Candidate
Member Candidate
Posts: 202
Joined: Tue Dec 11, 2012 12:56 am
Location: Greece

Re: v6.35rc [release candidate] is released, new wireless package!

Sat Mar 12, 2016 8:51 pm

Mikrotik will launch how much rc's to come to final version ???? 30? 40? 50?
If the goal is a more stable release, then the more rc's the better. Other companies do the same, the builds are just not publically available; just designated beta testers have access to them.

If you need stability, use the bugfix version.
Passionate about networks
Enthusiastic about Mikrotik
MTCNA | MTCRE | MTCINE

No trees were killed to send this message,
but a large number of electrons were terribly inconvenienced.
 
PeterDoBrasil
Member Candidate
Member Candidate
Posts: 134
Joined: Sun Aug 23, 2015 6:55 pm

Re: v6.35rc [release candidate] is released, new wireless package!

Sat Mar 12, 2016 8:56 pm

Mikrotik will launch how much rc's to come to final version ???? 30? 40? 50?
If the goal is a more stable release, then the more rc's the better. Other companies do the same, the builds are just not publically available; just designated beta testers have access to them.

If you need stability, use the bugfix version.
This was only a question! My prefered update option always is the rc's because there are a lot of good new things!
 
User avatar
kometchtech
Member Candidate
Member Candidate
Posts: 194
Joined: Sat Jun 15, 2013 4:25 am
Location: Japan
Contact:

Re: v6.35rc [release candidate] is released, new wireless package!

Sun Mar 13, 2016 1:59 pm

In rc26, and it has been in CAPsMAN configuration, from the DHCP Server, which is activated in the other RB, has been confirmed a phenomenon in which the IP address is not passed.
Moreover, instead of immediately occur, but after the elapse of a few hours if you are using.

It has not been output, especially something like anxious to log.

If you have enabled local forwarding, it seems this phenomenon is likely to occur.
--
Routerboard Users Group JP
http://www.rb-ug.jp/
CCR1009-8G-1S-1S+, RB750Gr3, CRS226-24G-2S+, RB850Gx2, RB960PGS, CRS317-1G-16S+,
RB2011UAS, CRS125-24G-1S, RB962UiGS-5HacT2HnT, CRS212-1G-10S-1S+, RB3011UiAS
 
m94646602
newbie
Posts: 38
Joined: Thu Oct 03, 2013 5:38 pm

Intel 5300AGN ping loss

Mon Mar 14, 2016 9:16 am

I use 6.35rc26 wireless-rep (AP mode), my laptop (WIN7 INTEL wireless 5300AGN) had a lot of PING loss, when I changed to WIRELESS-CM2, everything is normal.
 
User avatar
omidkosari
Trainer
Trainer
Posts: 613
Joined: Fri Sep 01, 2006 4:18 pm
Location: Iran , Karaj
Contact:

Re: v6.35rc [release candidate] is released, new wireless package!

Mon Mar 14, 2016 10:59 am

Is there any chance to implementation of
http://forum.mikrotik.com/viewtopic.php ... 50#p235456
Umetered Content for PPPoE . 'Unmetered Content' services aren't counted against your monthly download/upload inclusion

http://forum.mikrotik.com/viewtopic.php?t=59745

Mikrotik staff ?
MTCNA , MTCRE, MTCWE, Mikrotik Certified Trainer
 
User avatar
omidkosari
Trainer
Trainer
Posts: 613
Joined: Fri Sep 01, 2006 4:18 pm
Location: Iran , Karaj
Contact:

Re: v6.35rc [release candidate] is released, new wireless package!

Mon Mar 14, 2016 11:03 am

Is there any chance to implementation of
http://forum.mikrotik.com/viewtopic.php ... 50#p235456
Umetered Content for PPPoE . 'Unmetered Content' services aren't counted against your monthly download/upload inclusion

http://forum.mikrotik.com/viewtopic.php?t=59745

Mikrotik staff ?
http://www.cisco.com/c/en/us/products/i ... index.html
MTCNA , MTCRE, MTCWE, Mikrotik Certified Trainer
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: Intel 5300AGN ping loss

Mon Mar 14, 2016 11:06 am

I use 6.35rc26 wireless-rep (AP mode), my laptop (WIN7 INTEL wireless 5300AGN) had a lot of PING loss, when I changed to WIRELESS-CM2, everything is normal.
Please contact support@mikrotik.com and attach a support output file which is made when you have the ping loss.
  • 1
  • 4
  • 5
  • 6
  • 7
  • 8
  • 11

Who is online

Users browsing this forum: No registered users and 7 guests