Community discussions

  • 1
  • 4
  • 5
  • 6
  • 7
  • 8
 
pe1chl
Forum Guru
Forum Guru
Posts: 5522
Joined: Mon Jun 08, 2015 12:09 pm

Re: v6.39rc [release candidate] is released

Mon Mar 27, 2017 11:21 am

I had this problem going from v6.38.4 to 6.38.5 on the RB3011 also. Unfortunantly the router is one of my main routers, and I didn't have a spare so I couldn't debug.
In that scenario it is not wise to run RC software... I hope at least you make backups and/or exports and store them on another computer.
 
picacho99
newbie
Posts: 42
Joined: Mon Sep 08, 2014 7:16 pm

Re: v6.39rc [release candidate] is released

Mon Mar 27, 2017 1:14 pm

I had this problem going from v6.38.4 to 6.38.5 on the RB3011 also. Unfortunantly the router is one of my main routers, and I didn't have a spare so I couldn't debug.
In that scenario it is not wise to run RC software... I hope at least you make backups and/or exports and store them on another computer.
What is wrong with "zcybercomputing"?

One may decide to try RC software....Recover the device via netinstall and restore a backup requires no more than 10', and of course we, all, have backups and exports stored on another computer: in RB3011 partitions do not work...yes, it is suposed to work on v6.39.RC5X but no way to try it becuase leaves RB3011 unusable.

A RB3011 bought by the end of 2015, with historical debts (bridges, the announced desktop version with wireless, partitions, hardware encryption, ....)....from the "promissing" new ARM Mikrotik architecture that has never got additional devices launched.
 
zcybercomputing
just joined
Posts: 17
Joined: Tue Feb 14, 2017 4:10 am

Re: v6.39rc [release candidate] is released

Mon Mar 27, 2017 1:32 pm

I had this problem going from v6.38.4 to 6.38.5 on the RB3011 also. Unfortunantly the router is one of my main routers, and I didn't have a spare so I couldn't debug.
In that scenario it is not wise to run RC software... I hope at least you make backups and/or exports and store them on another computer.
I know this is the RC thread, but if you check the version numbers I cited, you may get my point that this particular error also has effected the current releases. A boot loop as a result of firmware upgrade in the current released version is extremely concerning. I hope this gets sorted before this version gets out of RC. I would run the stable release on this router, but I need the new dude features of v6.38.x

Since this event, I have begun frequent full export, backup, and file system downloads...

None of the features I am using has caused the problem to resurface, but I will not upgrade or reinstall the extra packages I wanted to play with until this appears to be resolved.
 
User avatar
jspool
Member
Member
Posts: 388
Joined: Sun Oct 04, 2009 4:06 am
Location: Oregon

Re: v6.39rc [release candidate] is released

Tue Mar 28, 2017 2:43 am

What's new in 6.39rc4 (2016-Dec-30 07:16):

!) ppp - completely rewritten internal fragmentation algorithm (when MRRU is used), optimized for multicore;
*) capsman - added CAP discovery interface list support;
*) ethernet - renamed "rx-lose" to "rx-loss" in ethernet statistics;
*) health - report fan speed for RB800 and RB1100 when 3-pin fan is being used;
*) led - show warning on print when "modem-signal-threshold" is not available;
*) lte - added error handling for remote AT execute;
*) wAP ac - improved 2.4GHz wireless performance;
*) wireless - added "station-roaming" setting (cli only);
*) wireless - show comment on "security-profile" if it is set (cli only);

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.

Its so nice to be able to connect to Rest API's with the new post method!!! My Mikrotiks are now happily sending me SMS alerts via API. It does come back with "failure" in the terminal when I run the command however it actually does work fine. cURL reports success but Mikrotik does not show success but it does seem to work fine. Thanks for adding this feature. Look forward to it hitting the stable release.
 
moep
newbie
Posts: 48
Joined: Mon Jul 02, 2012 2:12 pm

Re: v6.39rc [release candidate] is released

Wed Mar 29, 2017 3:39 pm

Hello,

*) wireless - fixed false positive DFS radar detection caused by iPhone 6s devices;

this problem still persists with version 6.39rc58

please fix

it is also not necessarily related to iphone 6s devices but occurs randomly (could be that a 6s is walking by, but thats just guessing)

Thank you
 
athurdent
just joined
Posts: 24
Joined: Fri Sep 09, 2016 7:02 pm

Re: v6.39rc [release candidate] is released

Wed Mar 29, 2017 3:45 pm

Hello,

*) wireless - fixed false positive DFS radar detection caused by iPhone 6s devices;

this problem still persists with version 6.39rc58

please fix

it is also not necessarily related to iphone 6s devices but occurs randomly (could be that a 6s is walking by, but thats just guessing)

Thank you
This should get fixed in rc59, MikroTik had access to my hAP AC and after a few debug firmwares the problem was no longer reproducible with my 6s.
 
User avatar
dash
newbie
Posts: 37
Joined: Tue Apr 28, 2015 12:05 pm

Re: v6.39rc [release candidate] is released

Thu Mar 30, 2017 5:01 pm

I am facing issues with the 6.39rc58 on an RB952 (6.39rc58 port1) which is POE powered from an RB3011 (6.38.5, LAN port 10). After updating the RB952 with the rc58 frimware POE does not turn it on again. I had to use the standard 24v power supply to get it up and running before i was able to downgrade to the 6.38.5 package. In 6.38.5 POE works with no issue...
 
jondavy
Member Candidate
Member Candidate
Posts: 124
Joined: Tue May 12, 2009 11:14 pm
Location: Brasil

Re: v6.39rc [release candidate] is released

Sat Apr 01, 2017 12:13 am

when i set:

/interface bridge settings
set use-ip-firewall=yes use-ip-firewall-for-vlan=yes

is not catching VLAN QinQ traffic into firewall
 
User avatar
strods
MikroTik Support
MikroTik Support
Topic Author
Posts: 1406
Joined: Wed Jul 16, 2014 7:22 am
Location: Riga, Latvia

Re: v6.39rc [release candidate] is released

Mon Apr 03, 2017 3:17 pm

Verison 6.39rc60 has been released.

Changes since previous version;
*) dhcpv4-server - by default make server “authoritativeâ€;
*) ethernet - fixed "loop-protect" on "master-port";
*) ethernet - fixed rare switch chip hang (could cause port flapping);
*) ike2 - fixed ctr mode;
*) ipsec - enable aes-ni on i386 and x64 for cbc, ctr and gcm modes;
*) ipsec - renamed "hw-authenc" flag to "hw-aead";
*) log - do not show changes in packet if NAT has not been used;
*) tr069-client - fixed XML special character parsing;
*) tr069-client - hide "Device.PPP.Interface.{i}.Password" value;
*) tr069-client - make more Parameters deny active notifications;
*) wireless - fixed crash while running "spectral-scan";
*) wireless - fixed false positive DFS radar detection caused by iPhone 6s devices;

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.
 
dyke
just joined
Posts: 1
Joined: Mon Apr 03, 2017 4:43 pm

Re: v6.39rc [release candidate] is released

Mon Apr 03, 2017 4:54 pm

*) ethernet - fixed rare switch chip hang (could cause port flapping);
Does this fix is related to [Ticket#2017032822000978]?
 
User avatar
strods
MikroTik Support
MikroTik Support
Topic Author
Posts: 1406
Joined: Wed Jul 16, 2014 7:22 am
Location: Riga, Latvia

Re: v6.39rc [release candidate] is released

Tue Apr 04, 2017 5:34 pm

Version 6.39rc62 has been released.

Changes since previous version:
!) firewall - discontinued support for p2p matcher (old rules will become invalid);
*) capsman - added "extension-channel" XX and XXXX auto matching modes (CLI only);
*) capsman - added "keepalive-frames" setting (CLI only);
*) capsman - added "skip-dfs-channels" setting (CLI only);
*) capsman - added ability to specify multiple channels in frequency field (CLI only);
*) capsman - added DFS support;
*) capsman - added support for "background-scan" and channel "reselect-interval" (CLI only);
*) capsman - changed channel "width" name to "control-channel-width" and changed default values (CLI only);
*) fastpath - fixed rare crash on devices with dynamic interfaces;
*) smips - reduced RouterOS main package size;
*) tile - optimized hardware encryption;
*) tr069-client - added firewall NAT support using vendor Parameters;
*) tr069-client - added support for uploading/downloading factory script;
*) webfig - correctly specify routing filter prefix;
*) winbox - allow to specify "route-distance" in "dhcp-client" if "special-classless" mode is selected;
*) winbox - do not allow Packet Sniffer "memory-limit" lower than 10KiB;
*) winbox - fixed "Montly" typo to "Monthly" in Graphing menu;
*) winbox - hide health menu on RB450;
*) winbox - properly show "dhcp-server" warnings;
*) winbox - properly show IPSec "installed-sa" "enc-algorithm" when it is aes-gcm;
*) winbox - set default "dhcp-client" "default-route-distance" value to 1;
*) winbox - show PoE-OUT current, voltage and power only on devices which can report these values;
*) wireless - added PEAP authentication support for wireless station mode (CLI only);

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.
 
paulct
Member Candidate
Member Candidate
Posts: 284
Joined: Fri Jul 12, 2013 5:38 pm

Re: v6.39rc [release candidate] is released

Tue Apr 04, 2017 5:38 pm

Version 6.39rc62 has been released.
*) wireless - added PEAP authentication support for wireless station mode;
Wow, finally ;) nice
 
pe1chl
Forum Guru
Forum Guru
Posts: 5522
Joined: Mon Jun 08, 2015 12:09 pm

Re: v6.39rc [release candidate] is released

Tue Apr 04, 2017 6:03 pm

Version 6.39rc62 has been released.
*) wireless - added PEAP authentication support for wireless station mode;
Wow, finally ;) nice
Hooray!!! Finally we can phase out PSK!
 
moep
newbie
Posts: 48
Joined: Mon Jul 02, 2012 2:12 pm

Re: v6.39rc [release candidate] is released

Tue Apr 04, 2017 6:57 pm

still not fixed in 6.39rc62 :(
Hello,

*) wireless - fixed false positive DFS radar detection caused by iPhone 6s devices;

this problem still persists with version 6.39rc58

please fix

it is also not necessarily related to iphone 6s devices but occurs randomly (could be that a 6s is walking by, but thats just guessing)

Thank you
This should get fixed in rc59, MikroTik had access to my hAP AC and after a few debug firmwares the problem was no longer reproducible with my 6s.
 
Marino
Frequent Visitor
Frequent Visitor
Posts: 51
Joined: Sun Jun 14, 2015 7:26 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 1:09 am

RB750GR3 doesn't boot. Crashes and reboot loop.
Version 6.39rc62 has been released.

Changes since previous version:
!) firewall - discontinued support for p2p matcher (old rules will become invalid);
*) capsman - added "extension-channel" XX and XXXX auto matching modes;
*) capsman - added "keepalive-frames" setting;
*) capsman - added "skip-dfs-channels" setting;
*) capsman - added ability to specify multiple channels in frequency field;
*) capsman - added DFS support;
*) capsman - added support for "background-scan" and channel "reselect-interval";
*) capsman - changed channel "width" name to "control-channel-width" and changed default values;
*) fastpath - fixed rare crash on devices with dynamic interfaces;
*) smips - reduced RouterOS main package size;
*) tile - optimized hardware encryption;
*) tr069-client - added firewall NAT support using vendor Parameters;
*) tr069-client - added support for uploading/downloading factory script;
*) webfig - correctly specify routing filter prefix;
*) winbox - allow to specify "route-distance" in "dhcp-client" if "special-classless" mode is selected;
*) winbox - do not allow Packet Sniffer "memory-limit" lower than 10KiB;
*) winbox - fixed "Montly" typo to "Monthly" in Graphing menu;
*) winbox - hide health menu on RB450;
*) winbox - properly show "dhcp-server" warnings;
*) winbox - properly show IPSec "installed-sa" "enc-algorithm" when it is aes-gcm;
*) winbox - set default "dhcp-client" "default-route-distance" value to 1;
*) winbox - show PoE-OUT current, voltage and power only on devices which can report these values;
*) wireless - added PEAP authentication support for wireless station mode;

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.
 
mducharme
Trainer
Trainer
Posts: 788
Joined: Tue Jul 19, 2016 6:45 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 3:11 am

*) tr069-client - added support for uploading/downloading factory script;
Wow! That's excellent! How??
 
User avatar
nz_monkey
Forum Guru
Forum Guru
Posts: 1810
Joined: Mon Jan 14, 2008 1:53 pm
Location: Straya
Contact:

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:51 am

*) capsman - added ability to specify multiple channels in frequency field;
Hi Strods,

Can you give an example of how you would use this ?

Is this so that Auto-Channel will only select one of the frequencies listed ?
http://thebrotherswisp.com/ | Mikrotik MTCNA, MTCRE, MTCINE | Fortinet FTCNA, FCNSP, FCT | Extreme Networks ENA
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 9:41 am

*) capsman - added ability to specify multiple channels in frequency field;
Is this so that Auto-Channel will only select one of the frequencies listed ?
Yes, it will choose one of the specified frequencies.
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 9:43 am

still not fixed in 6.39rc62 :(
Hello,

*) wireless - fixed false positive DFS radar detection caused by iPhone 6s devices;

this problem still persists with version 6.39rc58

please fix

it is also not necessarily related to iphone 6s devices but occurs randomly (could be that a 6s is walking by, but thats just guessing)

Thank you
This should get fixed in rc59, MikroTik had access to my hAP AC and after a few debug firmwares the problem was no longer reproducible with my 6s.
Please tell us more info what causes the DFS this time? iPhone 6S or some other device? Maybe you could provide us with the remote access to the AP so we could monitor that?
 
MayestroPW
newbie
Posts: 47
Joined: Wed Oct 26, 2016 3:28 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 1:25 pm

*) capsman - added support for "background-scan" and channel "reselect-interval";
How does background-scan works? In winbox I still can't run background scan on capsman interfaces.
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 1:34 pm

*) capsman - added support for "background-scan" and channel "reselect-interval";
How does background-scan works? In winbox I still can't run background scan on capsman interfaces.
Winbox support for all the new CAPsMAN Features are not made yet. You need to use console.
As soon as the CAP starts to operate in a frequency you can run the background scan on it.
 
MayestroPW
newbie
Posts: 47
Joined: Wed Oct 26, 2016 3:28 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 1:37 pm

When I start background scan on cap it tells me:
failure: background scan not supported in this state
I ran it from cap router, not from capsman router.
 
pe1chl
Forum Guru
Forum Guru
Posts: 5522
Joined: Mon Jun 08, 2015 12:09 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:25 pm

Version 6.39rc62 has been released.

Changes since previous version:
*) wireless - added PEAP authentication support for wireless station mode (CLI only);
Ok, CLI only was added later... I was checking via WebFig.
How is it done?

/interface wireless security-profiles
add name="peap" mode=dynamic-keys authentication-types=wpa2-eap eap-methods=peap

now I still have to config the "anonynous identity", "username" and "password".
Do I use the existing fields supplicant-identity mschapv2-username and mschapv2-password
for that? (meaning the only thing missing from Webfig is the eap-methods=peap in the pulldown?)
Or is there some other place to enter anonymous identity?
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:33 pm

When I start background scan on cap it tells me:
failure: background scan not supported in this state
I ran it from cap router, not from capsman router.
It will be only supported from the CAPsMAN side.
 
MayestroPW
newbie
Posts: 47
Joined: Wed Oct 26, 2016 3:28 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:40 pm

When I start background scan on cap it tells me:
failure: background scan not supported in this state
I ran it from cap router, not from capsman router.
It will be only supported from the CAPsMAN side.
Then how to run that scan?

UPDATE:

Ok, I found scan option, but need to add some channels to list I think.
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:41 pm

When I start background scan on cap it tells me:
failure: background scan not supported in this state
I ran it from cap router, not from capsman router.
It will be only supported from the CAPsMAN side.
Then how to run that scan?
From the CAPsMAN:

[admin@CAPsMAN] /caps-man interface> scan cap1
Flags: A - active, P - privacy, R - routeros-network, N - nstreme, T - tdma, W - wds, B - bridge
ADDRESS SSID CHANNEL SIG NF SNR RADIO-NAME ROUTEROS-VERSION
A R B 00:0C:42:05:01:27 Demo2 5180/20/a -65 -103 38 demo2 6.39rc60
 
MayestroPW
newbie
Posts: 47
Joined: Wed Oct 26, 2016 3:28 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:44 pm

Is there any possibility in future, that we could set other modes in cap settings than ap mode? I wish there was a station mode...
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:49 pm

Version 6.39rc62 has been released.

Changes since previous version:
*) wireless - added PEAP authentication support for wireless station mode (CLI only);
Ok, CLI only was added later... I was checking via WebFig.
How is it done?

/interface wireless security-profiles
add name="peap" mode=dynamic-keys authentication-types=wpa2-eap eap-methods=peap

now I still have to config the "anonynous identity", "username" and "password".
Do I use the existing fields supplicant-identity mschapv2-username and mschapv2-password
for that? (meaning the only thing missing from Webfig is the eap-methods=peap in the pulldown?)
Or is there some other place to enter anonymous identity?
Yes, you need to specify the mschapv2-username/password setting. Also I suggest to set the tls-mode=do-not-verify-certificate option.
Outer TLS identity is used from the supplicant-identity and inner TLS identity is used the mschapv2-username.
 
moep
newbie
Posts: 48
Joined: Mon Jul 02, 2012 2:12 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:50 pm

still not fixed in 6.39rc62 :(
Hello,

*) wireless - fixed false positive DFS radar detection caused by iPhone 6s devices;

this problem still persists with version 6.39rc58

please fix

it is also not necessarily related to iphone 6s devices but occurs randomly (could be that a 6s is walking by, but thats just guessing)

Thank you
This should get fixed in rc59, MikroTik had access to my hAP AC and after a few debug firmwares the problem was no longer reproducible with my 6s.
Please tell us more info what causes the DFS this time? iPhone 6S or some other device? Maybe you could provide us with the remote access to the AP so we could monitor that?
First of all: I had the problems with version 6.39rc60 not rc62. I now upgraded to rc62 and will check again.
the problem occured mainly in the middle of the day when I am not there or in the middle of the night, so I have no clue which device it could have been. there is no iPhone 6s present. the problem first appeared upgrading from 6.38.3 to 6.38.5.

a side note: the throughput from 6.38.5 to 6.39rc62 is now much better. in 6.38.5 I could barely get 100Mbps http throuput at 866MBit/s Phy-Rate. Now I am able to get almost 200 Mbps. This is not as great as it was with pre 6.38.x but much better than with 6.38.x :)
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 4:55 pm

Is there any possibility in future, that we could set other modes in cap settings than ap mode? I wish there was a station mode...
Current CAPsMAN implementation doesn't support that and we do not plan to add that in near future.
 
pe1chl
Forum Guru
Forum Guru
Posts: 5522
Joined: Mon Jun 08, 2015 12:09 pm

Re: v6.39rc [release candidate] is released

Wed Apr 05, 2017 5:05 pm

Yes, you need to specify the mschapv2-username/password setting. Also I suggest to set the tls-certificate=do-not-verify-certificate option.
Outer TLS identity is used from the supplicant-identity and inner TLS identity is used the mschapv2-username.
Ok thanks, that is clear to me. I'll try to test it soon. Hopefully you can add the PEAP method to the dropdown list in WebFig soon.
(most config work is done via WebFig here, I never use WinBox and use CLI when required)
 
moep
newbie
Posts: 48
Joined: Mon Jul 02, 2012 2:12 pm

Re: v6.39rc [release candidate] is released

Thu Apr 06, 2017 4:03 pm

First of all: I had the problems with version 6.39rc60 not rc62. I now upgraded to rc62 and will check again.
the problem occured mainly in the middle of the day when I am not there or in the middle of the night, so I have no clue which device it could have been. there is no iPhone 6s present. the problem first appeared upgrading from 6.38.3 to 6.38.5.

a side note: the throughput from 6.38.5 to 6.39rc62 is now much better. in 6.38.5 I could barely get 100Mbps http throuput at 866MBit/s Phy-Rate. Now I am able to get almost 200 Mbps. This is not as great as it was with pre 6.38.x but much better than with 6.38.x :)
The problem is still present in 6.39rc62, it occured in the middle of the night (3:30)
 
uldis
MikroTik Support
MikroTik Support
Posts: 3424
Joined: Mon May 31, 2004 2:55 pm

Re: v6.39rc [release candidate] is released

Thu Apr 06, 2017 5:04 pm

First of all: I had the problems with version 6.39rc60 not rc62. I now upgraded to rc62 and will check again.
the problem occured mainly in the middle of the day when I am not there or in the middle of the night, so I have no clue which device it could have been. there is no iPhone 6s present. the problem first appeared upgrading from 6.38.3 to 6.38.5.

a side note: the throughput from 6.38.5 to 6.39rc62 is now much better. in 6.38.5 I could barely get 100Mbps http throuput at 866MBit/s Phy-Rate. Now I am able to get almost 200 Mbps. This is not as great as it was with pre 6.38.x but much better than with 6.38.x :)
The problem is still present in 6.39rc62, it occured in the middle of the night (3:30)
Then we would need remote access to install a debug package.
Please contact support@mikrotik.com
 
huntah
Member Candidate
Member Candidate
Posts: 263
Joined: Tue Sep 09, 2008 3:24 pm

Re: v6.39rc [release candidate] is released

Thu Apr 06, 2017 11:51 pm

Does the black list function in the discover info window of the dude client for windows work right in this build? In 6.38.3, and previous versions I don't see the . or ... buttons shown in the manual here.

http://wiki.mikrotik.com/wiki/Manual:Th ... _discovery

There is a related bug where dude discovers phantom devices on the broadcast and subnet IP addresses during discovery discussed here:
http://forum.mikrotik.com/viewtopic.php?f=8&t=118250
It seems this is not fixed even in 6.39rc62. How/where can we specify black list for discovery?
 
mducharme
Trainer
Trainer
Posts: 788
Joined: Tue Jul 19, 2016 6:45 pm

Re: v6.39rc [release candidate] is released

Fri Apr 07, 2017 9:55 pm

*) tr069-client - added support for uploading/downloading factory script;
I see info on this is now in the wiki, thanks. Can you confirm that this factory script also activates with the hardware reset button? Or only the software reset command? I am wondering if we still need to use netinstall to get a factory config that is reapplied even with the hardware reset button? The wiki did not make this clear.

Thanks!
 
picacho99
newbie
Posts: 42
Joined: Mon Sep 08, 2014 7:16 pm

Re: v6.39rc [release candidate] is released

Mon Apr 10, 2017 1:44 pm

For these experiencing problems installing 6.39rc on RB3011: in my case it only worked netinstall but using the version associated with the 6.39rc in the software dowloads section (it is named netinstall-6.39rcXX-tile.zip). Stable netinstall (currently named netinstall-6.38.5.zip) does not seems to work.

And yes...partitions appear to work, but I did not test a partition activated and installing a previuos RouterOS version...
 
huntah
Member Candidate
Member Candidate
Posts: 263
Joined: Tue Sep 09, 2008 3:24 pm

Re: v6.39rc [release candidate] is released

Mon Apr 10, 2017 8:15 pm

Does the black list function in the discover info window of the dude client for windows work right in this build? In 6.38.3, and previous versions I don't see the . or ... buttons shown in the manual here.

http://wiki.mikrotik.com/wiki/Manual:Th ... _discovery

There is a related bug where dude discovers phantom devices on the broadcast and subnet IP addresses during discovery discussed here:
http://forum.mikrotik.com/viewtopic.php?f=8&t=118250
It seems this is not fixed even in 6.39rc62. How/where can we specify black list for discovery?
It is fixed but It was changed and not documented in the Wiki.. The Address list is now linked to the IP Firewall Address-list.
Got this answer from support. So thanks again for support. This feature is very handy..
 
kissze
just joined
Posts: 2
Joined: Tue Apr 11, 2017 12:03 pm

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 1:57 pm

Hi,
After the upgrade, my hEX PoE lite(RB750UPr2) is keep forgetting the configuration after every reboot.
This is a know problem?
Have anybody a workaround for this or i have to wait for a new rc release (im already downgraded, no problem)?

With kind regards,
Zoltan
 
Kindis
Member Candidate
Member Candidate
Posts: 244
Joined: Tue Nov 01, 2011 6:54 pm

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 3:50 pm

Hi,
After the upgrade, my hEX PoE lite(RB750UPr2) is keep forgetting the configuration after every reboot.
This is a know problem?
Have anybody a workaround for this or i have to wait for a new rc release (im already downgraded, no problem)?
Don't know if this is related but I had a similar issue with my RB750Gr3 which turned out to be a storage problem. All changes only got committed to RAM and not to storage. A quick clean of old backups and my config is the same after a reboot.
 
User avatar
strods
MikroTik Support
MikroTik Support
Topic Author
Posts: 1406
Joined: Wed Jul 16, 2014 7:22 am
Location: Riga, Latvia

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 4:42 pm

Version 6.39rc68 has been released.

Changes since previous version:
*) capsman - added "extension-channel" XX and XXXX auto matching modes;
*) capsman - added "keepalive-frames" setting;
*) capsman - added "skip-dfs-channels" setting;
*) capsman - added ability to specify multiple channels in frequency field;
*) capsman - added support for "background-scan" (CLI only) and channel "reselect-interval";
*) capsman - changed channel "width" name to "control-channel-width" and changed default values;
*) ddns - improved "dns-update" authentication validation;
*) dhcpv4 - fixed string option parser;
*) ike2 - fixed disabled DPD;
*) ike2 - fixed last EAP auth payload type;
*) ike2 - improved logging;
*) ike2 - kill only child SAs which are not re-keyed by remote peer;
*) ipsec - disallow AH+ESP combined policies ;
*) ppp - fixed rare kernel failure when receiving IPv6 address on PPP interface;
*) tr069-client - made any Download RPC overwrite configuration except ".alter";
*) tr069-client - improved LTE monitoring process;
*) winbox - allowed to specify static-dns as list;
*) winbox - do not show "dpd-max-failures" on IKEv2;
*) winbox - fixed CAPsMAN channels frequency (allow to specify a list of them);
*) winbox - fixed IPSec "mode-config" DNS settings;
*) winbox - fixed issue when working IPSec policies were shown as invalid;
*) winbox - improved "/tool torch";
*) winbox - do not allow Packet Sniffer "memory-limit" and "file-limit" lower than 10KiB;
*) winbox - show "A" flag for IPSec policies;
*) winbox - show "H" flag for IPSec installed SAs;
*) wireless - added PEAP authentication support for wireless station mode;

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after crash.
 
nicob
just joined
Posts: 3
Joined: Tue Apr 11, 2017 5:11 pm

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 5:15 pm

I want to report an bootloop using rc68 on my tile. (CCR1009-8G-1S-1S+PC).
All interfaces shutdown after 10 seconds of starting services.

Currently I don't have a serial port on my laptop, so no console output for now :(
 
heaven
just joined
Posts: 13
Joined: Mon Aug 15, 2016 12:14 pm

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 5:25 pm

My hap ac lite is bootloop too on rc68
 
bbs2web
Member Candidate
Member Candidate
Posts: 197
Joined: Sun Apr 22, 2012 6:25 pm
Location: Johannesburg, South Africa
Contact:

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 5:30 pm

Spanning Tree is broken since 6.38. We want to implement redundant bridges, to link together carrier VLANs to customer ports or VLANs. The previous STP implementation was essentially similar to PVSTP (per VLAN Spanning Tree Protocol) but the new implementation results in routers sending and processing STP BPDU packets on ports which aren't members of the bridge. The simplest way of demonstrating this is to configure bridges on two different VLANs, on different routers which share the VLAN carrying network.

We link two RB433GL routers together by interconnecting ether2, then setup VLAN 10 on one and VLAN 11 on the other. We then finally add the VLAN interfaces to separate bridges and would expect each bridge to be root independently but they don't:

Router 1:
/interface vlan
  add interface=ether2 name=vlan10 vlan-id=10
/interface bridge
  add name=bridge-vlan10
/interface bridge port
  add bridge=bridge-vlan10 interface=vlan10
Router 2:
/interface vlan
  add interface=ether2 name=vlan11 vlan-id=11
/interface bridge
  add name=bridge-vlan11
/interface bridge port
  add bridge=bridge-vlan11 interface=vlan11
Status on Router 1:
[admin@Router 1] > int bridge monitor bridge-vlan10
                  state: enabled
    current-mac-address: 00:0C:42:F5:8D:7D
            root-bridge: yes
         root-bridge-id: 0x8000.00:0C:42:F5:8D:7D
         root-path-cost: 0
              root-port: none
             port-count: 1
  designated-port-count: 1
Status on Router 2:
[admin@Router 2] > int bridge monitor bridge-vlan11
                  state: enabled
    current-mac-address: D4:CA:6D:78:4A:8A
            root-bridge: no
         root-bridge-id: 0x8000.00:0C:42:F5:8D:7D
         root-path-cost: 10
              root-port: vlan11
             port-count: 1
  designated-port-count: 0

This was validated on both 6.38.5 and 6.39rc68. When downgrading to 6.37.5 it works as it should:
Status on Router 1:
                  state: enabled
    current-mac-address: 00:0C:42:F5:8D:7D
            root-bridge: yes
         root-bridge-id: 0x8000.00:0C:42:F5:8D:7D
         root-path-cost: 0
              root-port: none
             port-count: 1
  designated-port-count: 1
Status on Router 2:
                  state: enabled
    current-mac-address: D4:CA:6D:78:4A:8A
            root-bridge: yes
         root-bridge-id: 0x8000.D4:CA:6D:78:4A:8A
         root-path-cost: 0
              root-port: none
             port-count: 1
  designated-port-count: 1
 
biatche
Member Candidate
Member Candidate
Posts: 128
Joined: Tue Oct 13, 2015 6:50 am

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 5:46 pm

Spanning Tree is broken since 6.38. We want to implement redundant bridges, to link together carrier VLANs to customer ports or VLANs. The previous STP implementation was essentially similar to PVSTP (per VLAN Spanning Tree Protocol) but the new implementation results in routers sending and processing STP BPDU packets on ports which aren't members of the bridge. The simplest way of demonstrating this is to configure bridges on two different VLANs, on different routers which share the VLAN carrying network.

We link two RB433GL routers together by interconnecting ether2, then setup VLAN 10 on one and VLAN 11 on the other. We then finally add the VLAN interfaces to separate bridges and would expect each bridge to be root independently but they don't:

Router 1:
/interface vlan
  add interface=ether2 name=vlan10 vlan-id=10
/interface bridge
  add name=bridge-vlan10
/interface bridge port
  add bridge=bridge-vlan10 interface=vlan10
Router 2:
/interface vlan
  add interface=ether2 name=vlan11 vlan-id=11
/interface bridge
  add name=bridge-vlan11
/interface bridge port
  add bridge=bridge-vlan11 interface=vlan11
Status on Router 1:
[admin@Router 1] > int bridge monitor bridge-vlan10
                  state: enabled
    current-mac-address: 00:0C:42:F5:8D:7D
            root-bridge: yes
         root-bridge-id: 0x8000.00:0C:42:F5:8D:7D
         root-path-cost: 0
              root-port: none
             port-count: 1
  designated-port-count: 1
Status on Router 2:
[admin@Router 2] > int bridge monitor bridge-vlan11
                  state: enabled
    current-mac-address: D4:CA:6D:78:4A:8A
            root-bridge: no
         root-bridge-id: 0x8000.00:0C:42:F5:8D:7D
         root-path-cost: 10
              root-port: vlan11
             port-count: 1
  designated-port-count: 0

This was validated on both 6.38.5 and 6.39rc68. When downgrading to 6.37.5 it works as it should:
Status on Router 1:
                  state: enabled
    current-mac-address: 00:0C:42:F5:8D:7D
            root-bridge: yes
         root-bridge-id: 0x8000.00:0C:42:F5:8D:7D
         root-path-cost: 0
              root-port: none
             port-count: 1
  designated-port-count: 1
Status on Router 2:
                  state: enabled
    current-mac-address: D4:CA:6D:78:4A:8A
            root-bridge: yes
         root-bridge-id: 0x8000.D4:CA:6D:78:4A:8A
         root-path-cost: 0
              root-port: none
             port-count: 1
  designated-port-count: 1
I don't know if its related, but i have a hex[gateway]-crs125[switch]-hap/wap ac[access points] setup and with 6.38 on all devices. i use pretty standard default bridges, vlans and the CRS125 loses connectivity whenever theres a 6.38 device attached. i presume that default vlans/bridges do have rtsp enabled. wasted many hours trying to figure out what's wrong. worst of all, mikrotik doesnt seem interested in testing this. we have not heard any response so far on anything related to this in the forums. reverted to 6.37 for the time being
Last edited by biatche on Tue Apr 11, 2017 5:51 pm, edited 2 times in total.
 
pista
just joined
Posts: 9
Joined: Thu Aug 04, 2016 12:46 pm

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 5:46 pm

After upgrade there is bootloop on hAP ac. :( :( :(
How to repair it? :shock:
 
biatche
Member Candidate
Member Candidate
Posts: 128
Joined: Tue Oct 13, 2015 6:50 am

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 5:48 pm

seriously, rc should be renamed to alpha or testing. while current should be renamed to beta and bugfix to stable.
 
heaven
just joined
Posts: 13
Joined: Mon Aug 15, 2016 12:14 pm

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 5:53 pm

I try to restore hap ac lite by netinstall but nothing.((((((( how to restore it?



After 40 minutes I already restore it:
but strange situation. If I press reset button and power on there is not install new firmware, when I power on it without reset the router is flashed. The backups is erased on file list(((((
Last edited by heaven on Tue Apr 11, 2017 6:40 pm, edited 1 time in total.
 
User avatar
Chupaka
Forum Guru
Forum Guru
Posts: 8290
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 5:55 pm

On x86, rc68 says 'info failed: std failure: timeout (13)' after Login prompt and does not work :)

I pressed 'Enter', RouterOS rebooted, I logged in and typed 'ip ad pr'. Router hung.After some time - again 'info failed: std failure: timeout (13)'.

UPD: 'router rebooted because some critical program crashed'
Russian-speaking forum: https://forum.mikrotik.by/. Welcome!

For every complex problem, there is a solution that is simple, neat, and wrong.

MikroTik. Your life. Your routing.
 
sbeauchamp
newbie
Posts: 29
Joined: Fri Sep 16, 2016 3:27 pm

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 7:14 pm

IPIP and GRE interfaces are no longer working. Upgrading to 6.39.rc68, automatically removed all my IPIP tunnels. If i try to add them back via web or CLI the router crashes and reboots. On the cli i can do /int ipip add name=TUN1 and hit enter, i get the prompt for remote address but after i type it in and hit enter it crashes.

This is on a CCR1009
 
napismizpravu
Member Candidate
Member Candidate
Posts: 135
Joined: Sat Apr 09, 2011 1:27 pm
Location: czech

Re: v6.39rc [release candidate] is released

Tue Apr 11, 2017 7:36 pm

RB433UAH
update 6.39rc62 > 6.39rc68 => netinstall (install 6.39rc62)
  • 1
  • 4
  • 5
  • 6
  • 7
  • 8

Who is online

Users browsing this forum: No registered users and 9 guests