- is it the same improvement, as in 6.41.3 (identical description), or yet a new improvement (improving it even more), or did the improvement in 6.41.3 didn't work?!) tile - improved overall system performance and stability ("/system routerboard upgrade" required);
Try this topic viewtopic.php?f=7&t=132648 - RC builds are slightly better, but still crappy. Still no info from MT, only many complains from users.Since I just ordered a few. Is there any pointer to more information about that one?Still no fix for hAP ac2 poor WiFi performance unfortunatly.
Thanks for the feedback. I came across those issues only today in that announcement so I was looking for pointers only (yet).woro, pepek, Simono - We are working on fixes for wireless improvements. Please note that this is "user forum". In order to contact MikroTik staff, you should write to email@example.com. Please do not expect that your problem will be resolved after you have posted that on forum. Yes, we might notice your posts and topics, but official way is through an e-mail.
I have a CCR1009 thats connected to a cisco 2911. After about 10 days or so, latency suddenly becomes sporadic. Did not happen on 6.38.5. Does happen on 6.41.3, will the above listed in 6.41.4 fix this issue? As trivial as it sounds, admin down the port, and back up seems to fix it. We had to set both devices to auto negotiate for them to link up at all. I have tried emailing support on another larger issue with a RB1100AHx4, but Im not getting replies.......... I have asked for updates.......RouterOS version 6.41.4 has been released in public "current" channel!
!) tile - improved overall system performance and stability ("/system routerboard upgrade" required);
If you experience version related issues, then please send supout file from your router to firstname.lastname@example.org. File must be generated while router is not working as suspected or after some problem has appeared on device
Please keep this forum topic strictly related to this concrete RouterOS release.
Im not sure why I said CRS, it is a CCR1009. My mistake, I'm about half sick. What was addressed with the tile improvement? I have not upgraded it to 6.41.4 yet, the problem had shown itself ~10 days after upgrading to 6.41.3 from 6.38.5 which never missed a beat.mikeeg02 - Quoted fix is for CCR devices, not for the CRS. Does the same problem persist on 6.42rc version? Please test this if possible. If problem persist, then contact support.
# NAME RADIO-MAC MASTER-INTERFACE 0 MDBR cap21 E4:8D:8C:9E:89:AC none
# NAME RADIO-MAC MASTER-INTERFACE 0 MDBR hAP lite-1 E4:8D:8C:9E:89:AC none
II have come across exactly the same issue on RB3100 and also on a Dynadish, >>> after upgrading via winbox, then wait for reboot. The system thereafter apparently restarts imto a continual loop. As soon as it starts , it restarts. No time to configure setup or netinstall. Extremely frustrating.Updated a 2x CRS226 without a problem. But...... my RB2011 is stuck. I hear a beep every few seconds, display shows routerboot, starting kernel....... over and over again.
Power off/on does not solve anything. How to fix this (preferably without losing my config)?
Yeah, recently got the RB2011 back in use and forgot to back-up my config .
Of course, this is discussion forum, not helpdesk. You cannot monitor all topics and respond to all posts with symptoms of possible problem. But you can respond to problem discussed in at least five different topics (to which you respond to other questions). Just quick note "working on it" would reduce number of posts in these topics to half. Systematically ignoring all mentions about this problem seems very strange and suspicious. Admiring that there is a problem and you are trying to make it work is fair and trustworthy behavior.woro, pepek, Simono - We are working on fixes for wireless improvements. Please note that this is "user forum". In order to contact MikroTik staff, you should write to email@example.com. Please do not expect that your problem will be resolved after you have posted that on forum. Yes, we might notice your posts and topics, but official way is through an e-mail.
Upgraded SXT LTE remotely from 6.40.6 to 6.41,4, device rebooted after downloading new ros but I can't access the device anymore.
Arranged with client to meet onsite in the morning, will revert back once I have more re info
Any idea what is wrong now?dhcp,warning dhcp1 offering lease 192.168.7.247 for <MAC_OF_RB450G_HERE> without success