Community discussions

MikroTik App
 
hugomon
just joined
Posts: 5
Joined: Thu Jul 18, 2019 11:56 pm

Re: Usage GPON module SFP in Spain

Thu Nov 28, 2019 6:51 pm

Hi, I have problems with my ONT Alcatel-Lucent O-010S-P, I can't even connect by SSH. I have tried 192.168.1.10, among others, but there is no ping.
Does anyone know this model, and if it is compatible?
hugomon

My model ONT G-010S-P responds to pings in Mikrotik. Please check my steps.

1. Assign sfp1 as WAN interface (it will remove sfp1 from the bridge)

2. G-010S-P and other models will not expose ethernet interface unless fiber cable is connected (link-ok, rate 1Gbps)
[admin@MikroTik] > interface ethernet monitor sfp1 
                      name: sfp1
                    status: link-ok
          auto-negotiation: done
                      rate: 1Gbps
               full-duplex: yes
           tx-flow-control: no
           rx-flow-control: no
               advertising: 
  link-partner-advertising: 
        sfp-module-present: yes
               sfp-rx-loss: no
                  sfp-type: SFP-or-SFP+
        sfp-connector-type: SC
       sfp-link-length-9um: 20000m
           sfp-vendor-name: ALCATELLUCENT

3. Add IP address to the sfp1 interface
[admin@MikroTik] > ip address add address=192.168.1.15/24 interface=sfp1

4. [admin@MikroTik] > ping 192.168.1.10
SEQ HOST SIZE TTL TIME STATUS
0 192.168.1.10 56 64 0ms
1 192.168.1.10 56 64 0ms
2 192.168.1.10 56 64 1ms
3 192.168.1.10 56 64 3ms

5. telnet or ssh
[admin@MikroTik] > system telnet 192.168.1.10
[admin@MikroTik] > system ssh user=ONTUSER address=192.168.1.10
Thank you for your reply JeanPierre!; I will try this week and report here with the result.
 
AndreHro
just joined
Posts: 4
Joined: Thu Nov 21, 2019 11:44 pm

Re: Usage GPON module SFP in Spain

Thu Nov 28, 2019 9:03 pm

Hi, is there someone out there selling Zisa's or Carlitos SFP?

I tried contacting Zisa but they wouldn't sell me one.
Hi there,

I have the ZISA one. It won't work with my provider so I don't need it. Interested?

Best Regards.
Which provide do you use?
I’m interested if it’s not Movistar in Madrid.
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Thu Nov 28, 2019 9:44 pm



Hi there,

I have the ZISA one. It won't work with my provider so I don't need it. Interested?

Best Regards.
Which provide do you use?
I’m interested if it’s not Movistar in Madrid.
[/quote]

Hi,

My provider is outside of Spain. It is Telekom (T-Com) in Montenegro. A part of Deutsche Telekom. Do You know anything about the modules I asked in a few previous posts? Nobody is willing to reply about.

Best Regards.
 
AndreHro
just joined
Posts: 4
Joined: Thu Nov 21, 2019 11:44 pm

Re: Usage GPON module SFP in Spain

Thu Nov 28, 2019 10:01 pm

No, I only saw here that some people successfully running the Modul in Spain by modifying the PON LOID and Serial number to the values used from the provider. Since my provider is Movistar I ask about your provider.
I had contact to hilink they want technical details and after that no reply.
I also had contact to usourcetech about the Modul UGP-N1S
http://www.usourcetech.com/web/userfile ... _Rev01.pdf . But I not really sure if it will work.
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Thu Nov 28, 2019 10:46 pm

No, I only saw here that some people successfully running the Modul in Spain by modifying the PON LOID and Serial number to the values used from the provider. Since my provider is Movistar I ask about your provider.
I had contact to hilink they want technical details and after that no reply.
I also had contact to usourcetech about the Modul UGP-N1S
http://www.usourcetech.com/web/userfile ... _Rev01.pdf . But I not really sure if it will work.
Ok, I want to get rid of my zisa. In order to make it work here I would need to use its command line interface and I don't want to learn anymore how to do that. I need almost a plug n play option. What is Your offer?
 
User avatar
zlobster
newbie
Posts: 42
Joined: Sun Nov 20, 2016 2:47 pm

Re: Usage GPON module SFP in Spain

Fri Nov 29, 2019 2:09 am

Hola Friends
friend in Valencia asked for me help. he got good SFP stick. lot of options to modify serial\vendor\part number\ and more. sticks have open source openwrt
login web 192.168.1.57 or telnet to sfp

OEM company\\ dipperoptics\dpoptics stick numero D23446
Licensee company \\ hilinktech\ stick number HL23446

HILINK23446.jpg
Hello friend,

I am trying to replace my huawei router for a long time. I own ZISA OP151s but it doesnt work for me. Can You, please, let me know if the module You showed here works for You? Can You attach some web interface photos?

Best Regards.
Did you tinker with your Zisa? If so, what is changed?

Is your Zisa working?

Best I can do is 25€ + something reasonable for shipping.
 
hugomon
just joined
Posts: 5
Joined: Thu Jul 18, 2019 11:56 pm

Re: Usage GPON module SFP in Spain

Fri Nov 29, 2019 9:52 am

Hi, I have problems with my ONT Alcatel-Lucent O-010S-P, I can't even connect by SSH. I have tried 192.168.1.10, among others, but there is no ping.
Does anyone know this model, and if it is compatible?
hugomon

My model ONT G-010S-P responds to pings in Mikrotik. Please check my steps.

1. Assign sfp1 as WAN interface (it will remove sfp1 from the bridge)

2. G-010S-P and other models will not expose ethernet interface unless fiber cable is connected (link-ok, rate 1Gbps)
[admin@MikroTik] > interface ethernet monitor sfp1 
                      name: sfp1
                    status: link-ok
          auto-negotiation: done
                      rate: 1Gbps
               full-duplex: yes
           tx-flow-control: no
           rx-flow-control: no
               advertising: 
  link-partner-advertising: 
        sfp-module-present: yes
               sfp-rx-loss: no
                  sfp-type: SFP-or-SFP+
        sfp-connector-type: SC
       sfp-link-length-9um: 20000m
           sfp-vendor-name: ALCATELLUCENT

3. Add IP address to the sfp1 interface
[admin@MikroTik] > ip address add address=192.168.1.15/24 interface=sfp1

4. [admin@MikroTik] > ping 192.168.1.10
SEQ HOST SIZE TTL TIME STATUS
0 192.168.1.10 56 64 0ms
1 192.168.1.10 56 64 0ms
2 192.168.1.10 56 64 1ms
3 192.168.1.10 56 64 3ms

5. telnet or ssh
[admin@MikroTik] > system telnet 192.168.1.10
[admin@MikroTik] > system ssh user=ONTUSER address=192.168.1.10
Thank you for your reply JeanPierre!; I will try this week and report here with the result.
Bad news, it doesn't work, I can obtain a link ok in the module only if I disable speed auto-negotiation, and still can't ping or ssh to the GPON.

Image

Image
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Fri Nov 29, 2019 10:41 am

Hola Friends
friend in Valencia asked for me help. he got good SFP stick. lot of options to modify serial\vendor\part number\ and more. sticks have open source openwrt
login web 192.168.1.57 or telnet to sfp

OEM company\\ dipperoptics\dpoptics stick numero D23446
Licensee company \\ hilinktech\ stick number HL23446

HILINK23446.jpg
Hello friend,

I am trying to replace my huawei router for a long time. I own ZISA OP151s but it doesnt work for me. Can You, please, let me know if the module You showed here works for You? Can You attach some web interface photos?

Best Regards.
Did you tinker with your Zisa? If so, what is changed?

Is your Zisa working?

Best I can do is 25€ + something reasonable for shipping.
Hello,

The ZIsa is working. Total work hours about 6. Nothing changed, not even the firmware. The factory firmware is in it. However, the best I can do is 40 + 17 shipping to Spain. If You want the same brand new module like ZISA, please find it here https://www.aliexpress.com/item/33014127133.html. For what I could investigate with my chinese friends, this module is absolutely the same as zisa and is was also produced and designed by the same factory T&W.

Best Regards.
 
AndreHro
just joined
Posts: 4
Joined: Thu Nov 21, 2019 11:44 pm

Re: Usage GPON module SFP in Spain

Fri Nov 29, 2019 11:59 am

So for me 60 Euro including shipping would be ok.
Can you send me a message in the forum?
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Fri Nov 29, 2019 12:12 pm

So for me 60 Euro including shipping would be ok.
Can you send me a message in the forum?
HI,

I don't see an option to send You the message via forum. Please use email address spaxton.ligiston@yahoo.com . From there we can exchange details.

Best Regards.
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Sat Nov 30, 2019 2:04 am



Bad news, it doesn't work, I can obtain a link ok in the module only if I disable speed auto-negotiation, and still can't ping or ssh to the GPON.
hugomon
Try ip-scan to see if anything responds...

[admin@MikroTik] > tool ip-scan interface=sfp1 address-range=192.168.1.0/24
Flags: D - dhcp 
  ADDRESS         MAC-ADDRESS        TIME DNS                                       SNMP                                       NETBIOS                                      
  192.168.1.10    00:06:B5:BE:11:EF   1ms                                                                                                                                   
  192.168.1.15                        0ms

Change the sfp1 interface to 192.168.0.15 and scan 192.168.0.0/24. Repeat for 192.168.2.0/24, 192.168.3.0/24, 192.168.4.0/24 networks. I've have seen document claiming 192.168.4.254, 192.168.3.10, 192.168.1.251 to be ONT's configuration IP
 
jondavy
Member Candidate
Member Candidate
Posts: 139
Joined: Tue May 12, 2009 11:14 pm
Location: Brasil

Re: Usage GPON module SFP in Spain

Mon Dec 02, 2019 6:08 pm

note that many customers and operators use GPON
Normis, have you planned to launch any solution in the GPON? Branch, as we need OLT and ONUs from MikroTik urgent
 
hugomon
just joined
Posts: 5
Joined: Thu Jul 18, 2019 11:56 pm

Re: Usage GPON module SFP in Spain

Tue Dec 03, 2019 11:23 am



Bad news, it doesn't work, I can obtain a link ok in the module only if I disable speed auto-negotiation, and still can't ping or ssh to the GPON.
hugomon
Try ip-scan to see if anything responds...

[admin@MikroTik] > tool ip-scan interface=sfp1 address-range=192.168.1.0/24
Flags: D - dhcp 
  ADDRESS         MAC-ADDRESS        TIME DNS                                       SNMP                                       NETBIOS                                      
  192.168.1.10    00:06:B5:BE:11:EF   1ms                                                                                                                                   
  192.168.1.15                        0ms

Change the sfp1 interface to 192.168.0.15 and scan 192.168.0.0/24. Repeat for 192.168.2.0/24, 192.168.3.0/24, 192.168.4.0/24 networks. I've have seen document claiming 192.168.4.254, 192.168.3.10, 192.168.1.251 to be ONT's configuration IP
You was rigth @JeanPierre, the correct IP was 192.168.2.2. After configure NAT masquerade for sfp1 I can login with user: ONTUSER and password: SUGAR2A041

Image

That's the good news, the bad news is I can't configure anything once logged in. Nothing is displayed about the busybox and commands like onu gtcpg don't work.
Also it runs extremely slow, even when writing, becoming apparently frozen.
In any case, it's a progress, thank you.
 
Petronas
just joined
Posts: 19
Joined: Mon Aug 26, 2019 7:59 pm

Re: Usage GPON module SFP in Spain

Tue Dec 03, 2019 3:11 pm

It seems from his images this user does not have "administrator privileges".

run cd /
run uci show

use the help commands

can you upload?  to pastebin.com
 
minhng99
just joined
Posts: 3
Joined: Fri Nov 15, 2019 3:26 pm

Re: Usage GPON module SFP in Spain

Thu Dec 05, 2019 10:01 am

Hi, I have a uboot repo here that appears to work with the Alcatel-Lucent/Nokia GPON SFP, also the Huawei MA5671A
https://github.com/minhng99/u-boot_lantiq_falcon

more about this being discussed here: https://forum.openwrt.org/t/support-ma5 ... n/48042/21

It's not fully working yet and don't appear to work correctly with the G-010S-P (kernel panic, root= not found) but if we managed to fix this then we might be able to have a netconsole uboot working and it will be much easier to test firmware
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Tue Dec 31, 2019 5:52 pm

I managed to burn the integrated with the "sfp_i2c" commands shown above


Antonio's commands make more sense to me. He's on 14.07_ltq. I am on 12.09_ltq

** remove 12.09 variables **
fw_setenv nPassword
fw_setenv nSerial


** use 14.07 (Antonio post #210) **
fw_setenv ont_serial HWTN12345678
convert password to hex in rapidtables https://www.rapidtables.com/convert/num ... o-hex.html ---->> 0123456789 hex=30 31 32 33 34 35 36 37 38 39
uci set gpon.ploam.nPassword='0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39'
uci commit
reboot


** verify after reboot **
root@SFP:/# onu gtcsng
root@SFP:/# onu gtcpg

I write these commands and write correctly, then I check and they have not been written
Hello friend,

Have You managed to change the values and how?

Best Regards.
 
BackON
just joined
Posts: 7
Joined: Fri Jan 03, 2020 12:58 pm

Re: Usage GPON module SFP in Spain

Fri Jan 03, 2020 1:03 pm

I have more ifo from of DFP-34G-2C2

The chipset is a ZTE ZX279125
flash memory winbond 25q128fsg
other chip is atheros but i cant see the model
in the back have a chip k24c06 1546cdx and 25l95 1707 22649

i created on openwrt forum a post about it to suppport it if is posibble

https://forum.openwrt.org/t/dfp-34g-2c2-sfp/51641
 
88zz88
just joined
Posts: 2
Joined: Fri Nov 15, 2019 6:08 am

Re: Usage GPON module SFP in Spain

Wed Jan 08, 2020 2:48 am

Salute comrades
Last edited by 88zz88 on Sun Aug 23, 2020 8:40 pm, edited 4 times in total.
 
Newtman
just joined
Posts: 6
Joined: Fri Nov 09, 2018 8:30 pm

Re: Usage GPON module SFP in Spain

Sat Jan 25, 2020 6:00 pm

Hello,

I'm from Uruguay and our ISP use similar tecnology to Spain, in consecuence I guess I can use some GPON module.

What module are working now?

Is impossible to find Zisa module, but I read few post upper, CM5671A is equivalent... But is very expensive only for an experiment, because I can't found information online about it.
Carlitoxx's module is out of stock since an year now.

Thanks!
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Mon Jan 27, 2020 3:15 am

Hi, I have compiled a list of popular GPON modules. Let me know if I missed something or made a mistake.



=-=-=-=-=-=-=-= Chipset: Intel/Lantiq PEB98036 =-=-=-=-=-=-=-=-=-=-=-=
FGS202
Flash 8MB, RAM 1MB, System RTOS eCos
Pros- Quick start
Cons - Flash programming/soldering required for SN/Password change. It may overheat. No graphical web interface.


=-=-=-=-=-=-=-= Chipset: Intel/Lantiq PEB98035 =-=-=-=-=-=-=-=-=-=-=-=
MA5671A
Flash 16MB, RAM 64MB, System OpenWRT
Pros - Good compatibility with Huawei and third-party vendors. Highly configurable through commands.
Cons - Hardware adapter and soldering required for full shell. No graphical web interface. Change SN/Password via command line.
G-010S-P
Flash 16MB, RAM 64MB, System OpenWRT
Pros - Good compability with Alcatel/Nokia. Web interface. Highly configurable through CLI commands
Cons - IPTV may not work with third-party vendors.
CarlitoxxPro CPGOS03-0490 / HL23446
Flash 16MB, RAM 64MB, System OpenWRT
Pros - Good web interface. Several vendor profiles. Highly configurable through CLI commands. Supports LOID

The firmware is interchangeable between: Source Photonics SPS-34-24T-HP-TDFO, Huawei MA5671, Alcatel G-010S-P, Hilink HL23446, CarlitoxxPro CPGOS03-0490, Dasan H650SFP, DpOptics D23446
LAN interface can be switched from 1 Gbps to 2.5 Gbps(sgmii_mode variable is set to 5)


=-=-=-=-=-=-=-= Chipset: Intel/Lantiq PEB98035 =-=-=-=-=-=-=-=-=-=-=-=
G-010S-A
Flash 16MB, RAM 64MB, System OpenWRT
Pros - Good compability with Alcatel/Nokia. Web interface. Highly configurable through commands. Capable of 1Gbps or 2.5Gbps LAN mode. Web GUI.
Cons - IPTV may not work with third-party vendors, for some routers soldering pin#6 to ground is required (info on dslreports forum - CanadaBell BCM57810S NIC)


=-=-=-=-=-=-=-= Chipset: Intel/Lantiq PEB98035 =-=-=-=-=-=-=-=-=-=-=-=-=
Zisa OP151S
Flash 8MB, RAM 64MB, System T&W Linux atop of OpenWRT 10_03 or 12_09
Pros - Good web interface. A lot of commands.
Cons - It may overheat. Security considerations - some firmware is pre-filled with TR-069 servers.

The firmware interchangeable beetween: T&W TW2362H-CDEL, Zisa OP151S, D-LINK DPN-100, Zyxel PMG3000-D20B, CM5671A, Eltex NTU-SFP-100, Calix 100-03903


=-=-=-=-=-=-=-=-=-=-=-= Chipset: ZTE ZX279125 =-=-=-=-=-=-=-=-=-=-=-=-=-=
ZTE DFP-34G-2C2
Flash 16MB, RAM 32MB, System ZTE Linux
Pros - Extensive graphical network interface (GUI). Supports HGU(Router mode) and LOID.
Cons - Limited number CLI of commands.
Other products:
EXOT - DFP-3422



=-=-=-=-=-=-=-=-=-=-=-= Chipset: Realtek RTL8672 and/or RTL9601C =-=-=-=-=-=-=-=-=-=-=-=-=-=
RTL8672 Network Processor SoC controler
RTL9601C Ethernet/PON network bridge processor
Flash 16MB, System Linux version 2.6.30.9 - Realtek RSDK-1.5.6p2 - luna SDK V1.9.0
Pros - Extensive graphical network interface (GUI), supports LOID, HGU(Router mode), SN, password, MAC change. Low ambient temperature.
Cons- Web interface, SN change, and dual support for EPON/GPON will vary depending on how the final vendor configured the module.
Several product families built upon Realtek RSDK-1.5.6p2 are available:
1. V-SOL V2801F, C-Data FD511GX-RM0, OPTON GP801R, BAUDCOM BD-1234-SFM, CPGOS03-0490 v2.0
2. Ubiquiti - U-Fiber Instant, (telnet CLI only)
3. EXOT - EGS1
Last edited by JeanPierre on Tue Aug 18, 2020 5:26 pm, edited 20 times in total.
 
Newtman
just joined
Posts: 6
Joined: Fri Nov 09, 2018 8:30 pm

Re: Usage GPON module SFP in Spain

Wed Jan 29, 2020 5:08 pm

Thanks JeanPierre!!! Nice compilation of information.

MA5671A is very affordable and I understand work well. Isn't problem for my solder the EEPROM and read it. I have got a R809F with the correct sockets.

Any advice?

Thanks!
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Thu Jan 30, 2020 8:43 pm

My advice?
Intel/Lantiq 98035 if you are not afraid of programming and, for some modules, soldering. They sometimes appear on Canadian(ebay.ca) or Italian(ebay.it) national ebay websites.
I forgot to add that Intel chip 98035 has LAN interface that can be switched from 1 Gbps to 2.5 Gbps. Important for users whose ISPs offer higher speeds than 1Gbps. This applies only to modules with OpenWRT(sgmii_mode variable is set to 5)
The best Intel/langiq module was sold by CarlitoxxPro and Hilink. Unfortunately, they don't have them in stock. Since HL23446 firmware is available I will try to load it on my g-010s-p sfp module and see how it works!

For the rest, probably DFP-34G-2C2. It has a rich web interface. The module is available under different names but the casing has a distinctive appearance. Just look at the photos from previous posts. It says "PON STICK V01" on the board. A large number of these modules are available on aliexpress in the "anddear" shop
A few users here have these modules but we have not enough reports on how they work. The modules may not work with ISP's who check software versions.
 
kapook007
newbie
Posts: 41
Joined: Sat Jun 03, 2006 7:55 am

Re: Usage GPON module SFP in Spain

Sun Feb 23, 2020 12:00 pm

device MA5671A
isp1 use SN+password authentication > working for MA5671A / use fw_setenv ont_serial and uci set gpon.ploam.nPassword
isp2 use LOID+CHECKCODE authentication > not working for MA5671A

how to change LOID+CHECKCODE for MA5671A ?
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Tue Feb 25, 2020 2:54 am

how to change LOID+CHECKCODE for MA5671A ?
LOID - 1-24 characters
CHECKCODE(LOID PASSWORD) - 1-12 characters

If the firmware supports LOID authentication LOID+CHECKCODE parameters can be updated by changing two variables: omci_loid and omci_lpwd
fw_setenv omci_loid xxxxxxxxxxxxx
fw_setenv omci_lpwd xxxxxxxxxxxx
If LOID is disabled in the firmware try alternative software from CarlitoxxPro CPGOS03-0490
 
kapook007
newbie
Posts: 41
Joined: Sat Jun 03, 2006 7:55 am

Re: Usage GPON module SFP in Spain

Wed Feb 26, 2020 6:31 am

fw_setenv omci_loid xxxxxxxxxxxxx not working
fw_setenv omci_lpwd xxxxxxxxxxxx not working

Need backup firmware CPGOS03-0490
mtd0-mtd5
T T
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Thu Feb 27, 2020 6:51 am

Need backup firmware CPGOS03-0490
HL23446 shared above should be the same as CPGOS03-0490
 
xh116
just joined
Posts: 14
Joined: Wed Oct 17, 2018 3:44 pm

Re: Usage GPON module SFP in Spain

Tue Mar 03, 2020 7:47 am

Salute comrades

to your collection of GPON images working with Mikrotik SFP routers.

DASAN H650SFP - same hardware as SPS3424THPTDFO, MA5671A, G-010S-P
image login - ssh 192.168.1.10 ONTUSER/password unknown unless decoded from
ONTUSER:$6$mYQnmn3MLtYla6rV$DIlnn6XmGATG4RGr8U1O7mw8UQ/sZqOp4kPkSY672KmTjS4gvPIz1l3aLtQrPIxoe2q10pX4d.zmuzHtlrYux1:16934:0:99999:7:::
H650SFP image0 rev. 14_07
http://s000.tinyupload.com/index.php?fi ... 9384744300
H650SFP image1 rev. 14_07
http://s000.tinyupload.com/index.php?fi ... 6685759864

G-010S-P
image login - ssh 192.168.1.10 ONTUSER/SUGAR2A041
G-010S-P image0 rev. 14_07
http://s000.tinyupload.com/index.php?fi ... 6227675874
G-010S-P image1 rev.14_07
http://s000.tinyupload.com/index.php?fi ... 1873659888

HL23446
image login - telnet 192.168.1.57 no password
HL23446 image0 rev.14_07
http://s000.tinyupload.com/index.php?fi ... 4338451129
HL23446 image1 rev.14_07
http://s000.tinyupload.com/index.php?fi ... 3576121597
Hi
Do you have hl23446 firmware to download, My module is brick by mistake without backup...
Thanks in advance
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Tue Mar 03, 2020 7:52 am

Hi everyone,
I'm a GPON SFP ONU user in China, which is the country of most SFP hardware producing country.
According to what I know, most SFP use TW2312 as master chip (like Zisa OP151s,TW2312H-CDEL), which is manufacted by T&W, Shenzhen, China.
I have Zisa OP151s, TW2312H-CDEL and I believe CM5671A they all have same hardware.
Unfortunately most of them are end of life and the developer group was dismissed.

The problem I have is my SFP don't support some OMCI command. This makes it available to some ISPs, but not others.
I'd like to try your firmwares to workout a solution.

By the way, a former engineer of T&W create a new SFP ONU which use Realtek master chip, support GPON, EPON, SN, snid, loid, MAC, with only $38.
You do not have the required permissions to view the files attached to this post.
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Tue Mar 03, 2020 8:27 am

I have more ifo from of DFP-34G-2C2

The chipset is a ZTE ZX279125
flash memory winbond 25q128fsg
other chip is atheros but i cant see the model
in the back have a chip k24c06 1546cdx and 25l95 1707 22649

i created on openwrt forum a post about it to suppport it if is posibble

https://forum.openwrt.org/t/dfp-34g-2c2-sfp/51641
As mentioned above,ZTE is another manufacturers in China. As far as I am concerned, The framwork of ZX279125 is not same as lantiq.
What are your specific problems?
You do not have the required permissions to view the files attached to this post.
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Tue Mar 03, 2020 4:07 pm

Do you have hl23446 firmware to download, My module is brick by mistake without backup...

It looks that modules SPS3424THPTDFO, MA5671A, G-010S-P, CPGOS03-0490, H650SFP, HL23446 share the same MTD partition mapping.

root@SFP:/# cat /proc/mtd
dev: size erasesize name
mtd0: 00040000 00010000 "uboot"
mtd1: 00080000 00010000 "uboot_env"
mtd2: 00740000 00010000 "linux"
mtd3: 0061eedc 00010000 "rootfs"
mtd4: 00370000 00010000 "rootfs_data"
mtd5: 00800000 00010000 "image1"

Combine MTD parts from different modules to create the firmware
root@ubuntu:/# cat mtd0.bin mtd1.bin mtd2.bin mtd5.bin > firmware.bin

root@ubuntu:/# ls -l
-rw-r--r-- 1 root root 16777216 Nov 12 09:51 firmware.bin
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Tue Mar 03, 2020 4:10 pm

By the way, a former engineer of T&W create a new SFP ONU which use Realtek master chip, support GPON, EPON, SN, snid, loid, MAC, with only $38.

Can you share a photo or name of the new SFP ONU with Realtek chip?
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Wed Mar 04, 2020 7:38 am

By the way, a former engineer of T&W create a new SFP ONU which use Realtek master chip, support GPON, EPON, SN, snid, loid, MAC, with only $38.

Can you share a photo or name of the new SFP ONU with Realtek chip?
As your wish.

Left: G/Epon sfp with Realtek master chip
Right: TW2362H
I'll dismante it later because it is in use.
You do not have the required permissions to view the files attached to this post.
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Wed Mar 04, 2020 6:05 pm

Left: G/Epon sfp with Realtek master chip
Right: TW2362H
I'll dismante it later because it is in use.
Thanks.
I'm intrigued by what model of chip is used to make this SFP module. Is it possible that RTL9601C was used?
I found more pictures and setup screens
https://www.chiphell.com/thread-2184048-1-1.html

Can you recommend a place to buy this Realtek SFP.
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Thu Mar 05, 2020 4:07 am

Thanks.
I'm intrigued by what model of chip is used to make this SFP module. Is it possible that RTL9601C was used?
I found more pictures and setup screens
https://www.chiphell.com/thread-2184048-1-1.html

Can you recommend a place to buy this Realtek SFP.
Yes the thread of chiphell is correct.
# cat /proc/cpuinfo
system type             : RTL8672
processor               : 0
cpu model               : 56322
BogoMIPS                : 112.23
tlb_entries             : 64
mips16 implemented      : yes
# cat /proc/version
Linux version 2.6.30.9 (root@ubuntu12) (gcc version 4.4.6 (Realtek RSDK-1.5.6p2) ) #9 Thu Oct 24 20:18:35 CST 2019 [luna SDK V1.9.0]
# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00040000 00001000 "boot"
mtd1: 00002000 00001000 "env"
mtd2: 00002000 00001000 "env2"
mtd3: 0003c000 00001000 "config"
mtd4: 00300000 00001000 "k0"
mtd5: 004c0000 00001000 "r0"
mtd6: 00300000 00001000 "k1"
mtd7: 004c0000 00001000 "r1"
mtd8: 00001000 00001000 "Partition_008"
mtd9: 00001000 00001000 "Partition_009"
mtd10: 00001000 00001000 "Partition_010"
mtd11: 00001000 00001000 "Partition_011"
mtd12: 00300000 00001000 "linux"
mtd13: 004c0000 00001000 "rootfs"
# cat /proc/meminfo
MemTotal:          16944 kB
MemFree:            5352 kB
......
# dmesg
/bin/sh: dmesg: not found

Unfortunately it is only sold in mainland of China and the price goes up recently. Please refer here (interest irrelevant)
It is incompatible with CCR's SFP+. Only a few PCIe card tested and compatible, too.
So it is about $52+$32 postage with Universal Postal Union if you really want.
By the way, I really don't think it's worth it. A S/EPON modem with gigabytes port only $40 with shipping.
 
kapook007
newbie
Posts: 41
Joined: Sat Jun 03, 2006 7:55 am

Re: Usage GPON module SFP in Spain

Sat Mar 07, 2020 11:54 am

Bad news for DFP-34G-2C2
Image


route mode only
how change to bridge mode with vlan support ?


Image
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Mon Mar 09, 2020 2:12 pm

Bad news for DFP-34G-2C2
....(sorry for reduce)
route mode only
how change to bridge mode with vlan support ?
....(sorry for reduce)
ODI said bridge mode is not allowed by ZTE's warrant. Sorry.
[delete]But the function of bridge mode exists, maybe just need to complement some webpage files. ODI said they're trying.[/delete]
update 13 Mar:
A friend send me one of this sfp and I did some dig.
IT IS BRIDGED BY DEFAULT like a SFU, just don't create any connect in WAN Connection page.
It works with one of my ISP but not another, same like Lantiq.
It is not work with CCR1009's SFP+, only SFP works.
Last edited by piku on Fri Mar 13, 2020 5:06 pm, edited 1 time in total.
 
Newtman
just joined
Posts: 6
Joined: Fri Nov 09, 2018 8:30 pm

Re: Usage GPON module SFP in Spain

Fri Mar 13, 2020 3:37 pm

Hello!

I finally receive my first Mikrotik and SFP, a RB960PGS and MA5671A.
I'm fully noob with Mikrotik but after a couple of hours I logged in to the SFP via SSH.
My SFP need the fibber connected, the default IP is 192.168.1.10, credentials are root / admin123
After this I tried set my serial number and password without luck. The commands fw_setenv didn't work... But I found the command "set" work, but I don't know the name of the variables (I tried with "print" and other words like this)
I don't find manual or similar, commands like help or man are disable too... But I found this log.

root@192.168.1.10's password:
Welcome Visiting Huawei Home Gateway
Copyright by Huawei Technologies Co., Ltd.
# display_log
2018-04-30 21:18:21 Software successfully upgraded. Source version: V8R017C00S201. Target version: V8R017C00S206

If necessary I can read the EEPROM with my R809F, but I prefer not solder.

Anyone have experience with this dongle?

Thanks!!
You do not have the required permissions to view the files attached to this post.
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Fri Mar 13, 2020 5:23 pm

Hello!

I finally receive my first Mikrotik and SFP, a RB960PGS and MA5671A.
I'm fully noob with Mikrotik but after a couple of hours I logged in to the SFP via SSH.
My SFP need the fibber connected, the default IP is 192.168.1.10, credentials are root / admin123
After this I tried set my serial number and password without luck. The commands fw_setenv didn't work... But I found the command "set" work, but I don't know the name of the variables (I tried with "print" and other words like this)
I don't find manual or similar, commands like help or man are disable too... But I found this log.

root@192.168.1.10's password:
Welcome Visiting Huawei Home Gateway
Copyright by Huawei Technologies Co., Ltd.
# display_log
2018-04-30 21:18:21 Software successfully upgraded. Source version: V8R017C00S201. Target version: V8R017C00S206

If necessary I can read the EEPROM with my R809F, but I prefer not solder.

Anyone have experience with this dongle?

Thanks!!
Yes. It's almost same as SmartAX MA5671. try
set sn snid 5CA858829BE1
 
Newtman
just joined
Posts: 6
Joined: Fri Nov 09, 2018 8:30 pm

Re: Usage GPON module SFP in Spain

Fri Mar 13, 2020 5:42 pm

Hello!

I finally receive my first Mikrotik and SFP, a RB960PGS and MA5671A.
I'm fully noob with Mikrotik but after a couple of hours I logged in to the SFP via SSH.
My SFP need the fibber connected, the default IP is 192.168.1.10, credentials are root / admin123
After this I tried set my serial number and password without luck. The commands fw_setenv didn't work... But I found the command "set" work, but I don't know the name of the variables (I tried with "print" and other words like this)
I don't find manual or similar, commands like help or man are disable too... But I found this log.

root@192.168.1.10's password:
Welcome Visiting Huawei Home Gateway
Copyright by Huawei Technologies Co., Ltd.
# display_log
2018-04-30 21:18:21 Software successfully upgraded. Source version: V8R017C00S201. Target version: V8R017C00S206

If necessary I can read the EEPROM with my R809F, but I prefer not solder.

Anyone have experience with this dongle?

Thanks!!
Yes. It's almost same as SmartAX MA5671. try
set sn snid 5CA858829BE1
Thanks piku, I will try tomorrow.
Have you got a full manual of this sfp?

Thanks!!!
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Sat Mar 14, 2020 7:05 am

Thanks piku, I will try tomorrow.
Have you got a full manual of this sfp?

Thanks!!!
Sorry.
Huawei design it is to configurate from olt, not for separate work. So there is no official manual for commands.
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Tue Mar 17, 2020 9:46 pm

... But I found the command "set" work, but I don't know the name of the variables (I tried with "print" and other words like this)

I believe the "set" command only works with DyingGasp variable
# set nDyingGaspEnable enable
Result:Success
# set nDyingGaspEnable disable
Result:Success
 
kapook007
newbie
Posts: 41
Joined: Sat Jun 03, 2006 7:55 am

Re: Usage GPON module SFP in Spain

Tue Mar 24, 2020 5:13 pm

i try firmware
i have some problem about firmware for ma5671a

H650SFP image0 rev. 14_07
-working same ont
root@SFP:/# onu ploamsg
errorcode=0 curr_state=5


HL23446 notworking
-not found gpon signal

root@SFP:/# onu ploamsg
errorcode=0 curr_state=1

anyone have problem with me ?
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Tue Mar 24, 2020 7:11 pm

i try firmware
HL23446 notworking
-not found gpon signal
anyone have problem with me ?

@kapook007
Try this. It works for me
root@SFP:/# fw_setenv ont_serial HWTC1122334455
root@SFP:/# fw_setenv target oem-generic
root@SFP:/# uci set gpon.ploam.nPassword="0x31 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x30 0x39"
root@SFP:/# uci commit
root@SFP:/# reboot
It should keep the login 192.168.1.10 from MA5671A (telnet and http)

If you require more changes like model number, firmware version, MAC address, LOID have a look at Antonio's post
viewtopic.php?f=3&t=116364#p751330
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Wed Mar 25, 2020 2:50 pm

i try firmware
i have some problem about firmware for ma5671a

H650SFP image0 rev. 14_07
-working same ont
root@SFP:/# onu ploamsg
errorcode=0 curr_state=5


HL23446 notworking
-not found gpon signal

root@SFP:/# onu ploamsg
errorcode=0 curr_state=1

anyone have problem with me ?
O1 means not receive light. I doubt there is physical connection problem.
Dasan H650SFP is a product form Koera and SC/APC connecter is widely used in Korea, which is different from HL23446.
BTW, I'm not familiar with Korea. Just for your reference.
 
kapook007
newbie
Posts: 41
Joined: Sat Jun 03, 2006 7:55 am

Re: Usage GPON module SFP in Spain

Thu Mar 26, 2020 3:13 am

i try firmware
i have some problem about firmware for ma5671a

H650SFP image0 rev. 14_07
-working same ont
root@SFP:/# onu ploamsg
errorcode=0 curr_state=5


HL23446 notworking
-not found gpon signal

root@SFP:/# onu ploamsg
errorcode=0 curr_state=1

anyone have problem with me ?
O1 means not receive light. I doubt there is physical connection problem.
Dasan H650SFP is a product form Koera and SC/APC connecter is widely used in Korea, which is different from HL23446.
BTW, I'm not familiar with Korea. Just for your reference.
i already check physical connection
my device is ma5671a 1pc install 2 firmware
1.firmware H650SFP is working
2.firmware HL23446 not found gpon signal
i try in my home
 
piku
just joined
Posts: 16
Joined: Sat Feb 10, 2018 10:59 am

Re: Usage GPON module SFP in Spain

Thu Mar 26, 2020 2:38 pm

i already check physical connection
my device is ma5671a 1pc install 2 firmware
1.firmware H650SFP is working
2.firmware HL23446 not found gpon signal
i try in my home
my misunderstanding, sorry.
 
kapook007
newbie
Posts: 41
Joined: Sat Jun 03, 2006 7:55 am

Re: Usage GPON module SFP in Spain

Thu Mar 26, 2020 4:07 pm

Hi
HL23446 firmware not found gpon signal.
i test and got problem
HL23446 found gpon signal over -15dbm
But standart gpon signal is -20dbm to -28dbm HL23446 not found gpon signal

CarlitoxxPro CPGOS03-0490 can found gpon signal -20dbm to -28dbm ????
Anyone who can share CarlitoxxPro CPGOS03-0490 firmware.
mtd0 , mtd1 , mtd2
thanks
 
User avatar
CarlitoxxPro
just joined
Posts: 23
Joined: Wed Jan 04, 2017 10:15 am
Location: Spain
Contact:

Re: Usage GPON module SFP in Spain

Sat Apr 04, 2020 1:38 am

We are very happy :D by announce that we are currently on manufacturing process for the newest version of GPON ONU SFP CPGOS03-0490 V2.

New Architecture, more stability and a great interoperability between multiple OLT brands and Routers/Switches with SFP and SFP+ ports. Fully tested with TriplePlay Services (Data, VoIP, IPTV).

Its Time to replace that unreliable and limited HGU / ONT by a most advanced ONU SFP with a ultra low power compsumption and ready to work on the most faster FTTH networks.

More details very soon!! Please stay tuned. :wink:
Facebook
Twitter
Telegram

Image
Facebook: fb.me.com/CarlitoxxPro
Twitter: @CarlitoxxPro
Telegram: t.me/CarlitoxxPro
Email: contacto [at] carlitoxxpro.com
 
User avatar
osquetar
just joined
Posts: 10
Joined: Thu Feb 21, 2013 5:26 pm
Location: Barcelona
Contact:

Re: Usage GPON module SFP in Spain

Sat Apr 04, 2020 2:04 am

Ya era hora!
 
morishe
just joined
Posts: 1
Joined: Mon Apr 20, 2020 6:15 pm

Re: Usage GPON module SFP in Spain

Mon Apr 20, 2020 6:46 pm

I have also a MA5671 flashed with HL23446 firmware.

I didn't tried with the original firmware but (like yours) PLOAM state is 1.

Did you solve your problem?

Regards
i try firmware
i have some problem about firmware for ma5671a

H650SFP image0 rev. 14_07
-working same ont
root@SFP:/# onu ploamsg
errorcode=0 curr_state=5


HL23446 notworking
-not found gpon signal

root@SFP:/# onu ploamsg
errorcode=0 curr_state=1

anyone have problem with me ?
 
User avatar
iperezandres
Frequent Visitor
Frequent Visitor
Posts: 51
Joined: Mon Feb 13, 2017 1:17 pm
Location: Madrid
Contact:

Re: Usage GPON module SFP in Spain

Mon Apr 27, 2020 7:35 pm

C'mon Carlitos, we are looking forward to receiving more information and availability of your product!!!! :D
 
Newtman
just joined
Posts: 6
Joined: Fri Nov 09, 2018 8:30 pm

Re: Usage GPON module SFP in Spain

Tue Apr 28, 2020 2:02 am

... But I found the command "set" work, but I don't know the name of the variables (I tried with "print" and other words like this)

I believe the "set" command only works with DyingGasp variable
# set nDyingGaspEnable enable
Result:Success
# set nDyingGaspEnable disable
Result:Success
I confirm my SFP accept set nDyingGaspEnable enable/disable.
Obvisly the problem is the firmware, I can't configure anything or modify the variables without documentation. Next month I will receive a new programmer to dump the EEPROM. Maybe change the firmware could be a solution for me.
I can't connect directly to the SFP from the LAN, buy I'm not Mikrotik expert, is my first time... I don't understand how to bridge the networks 192.168.1.0/24 and 192.168.88.0/24.
 
jmj
just joined
Posts: 1
Joined: Sat Sep 07, 2019 4:28 am

Re: Usage GPON module SFP in Spain

Wed Apr 29, 2020 6:05 pm

Last edited by jmj on Wed Apr 29, 2020 6:06 pm, edited 1 time in total.
 
BackON
just joined
Posts: 7
Joined: Fri Jan 03, 2020 12:58 pm

Re: Usage GPON module SFP in Spain

Mon May 18, 2020 6:09 pm

Image


after checking that image in carlitoxx facebook looks like Dfp-34g-2c2 sfp module (the cage have the same screws and look the same.) this is a new chipset (ZTE) but the question is about the firmware... its going to be openwrt or custom firmware?
 
almeiras
just joined
Posts: 5
Joined: Fri Nov 15, 2019 9:16 pm

Re: Usage GPON module SFP in Spain

Tue May 19, 2020 1:42 pm

Hello guys, I have a Nokia g-010s-p (Alcatel-Lucent). I tried to update it from OpenWRT ltq 12 to 14 via web using a file (image 0) provided in this thread but it bricked.

Any guide on how to de-brick it? It looks like I should power it with 3.3V and reach the UART pins inside (probably while keeping the SC/APC connected since it wont power on otherwise)

Also, any cheap recommended GPON stick. Carlitoxxpro and Zisa sticks seem unavailable.

Thank you very much.
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Tue May 19, 2020 4:11 pm

Hello guys, I have a Nokia g-010s-p (Alcatel-Lucent). I tried to update it from OpenWRT ltq 12 to 14 via web using a file (image 0) provided in this thread but it bricked.

Any guide on how to de-brick it? It looks like I should power it with 3.3V and reach the UART pins inside (probably while keeping the SC/APC connected since it wont power on otherwise)

Also, any cheap recommended GPON stick. Carlitoxxpro and Zisa sticks seem unavailable.

Thank you very much.
Hello almeiras
It's easy if you have a TTL adapter connected to pins 2 and 7. Look at the instructions how to make or buy one written for MA5671A in the openwrt forum. Most of them should apply in this scenario..
 
almeiras
just joined
Posts: 5
Joined: Fri Nov 15, 2019 9:16 pm

Re: Usage GPON module SFP in Spain

Wed May 20, 2020 11:34 pm

Thank you! And how would you upload and install the firmware? (Or even a custom one). I know I can connect via screen / cu but then what? I can’t find any tutorials...

EDIT: Sorry, I found this: https://openwrt.org/docs/techref/hardware/port.serial
 
ivanmh
just joined
Posts: 1
Joined: Sat May 23, 2020 7:55 pm

Re: Usage GPON module SFP in Spain

Sat May 23, 2020 8:08 pm

Hi guys, Ubiquiti have released a new SFP GPON ONU stick called "UFiber Instant (UF-Instant)".

According to its specifications, it has SGMII Ethernet LAN interface. Would this allow working with the SFP+ connection for RB4011? It would be great if someone confirms it. I am a happy owner of a RB4011iGS+5HacQ2HnD-IN, working in harmony with a UFiber Nano G, but I'm curious to know if this new UFiber Instant would work with my RB4011.

Also, if its has the same web interface as its brothers UFiber Nano G & Loco, it should work with Movistar and other ISPs that work nice with UFiber. Except of course, VLAN2 for IPTV on Movistar ....

EDIT: Sorry, I was wrong. Reading instructions for use, this UFiber Instant has no web interface and is configured from a Ubiquiti OLT. It will not work for any Spanish ISP. My fault for not read the instructions for use before...
Last edited by ivanmh on Sat May 23, 2020 8:21 pm, edited 3 times in total.
 
almeiras
just joined
Posts: 5
Joined: Fri Nov 15, 2019 9:16 pm

Re: Usage GPON module SFP in Spain

Tue May 26, 2020 5:11 pm

Hello again!

So I managed to open my bricked (Nokia) Alcatel-Lucent G-010S-P. I found four empty pads on the board, hopefully the UART pins that I am looking for. Now, I have two questions:
  • Does anybody know the correct pinout? At least, can anybody confirm if these are the UART pins I am looking for?
  • Which soldering iron should I get for this kind of miniature soldering?
This image shows the possible UART pins and the opening procedure:
IMG_0713.jpg
Thank you very much for your help!
You do not have the required permissions to view the files attached to this post.
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Tue May 26, 2020 9:18 pm

Hello again!

So I managed to open my bricked (Nokia) Alcatel-Lucent G-010S-P. I found four empty pads on the board, hopefully the UART pins that I am looking for. Now, I have two questions:
  • Does anybody know the correct pinout? At least, can anybody confirm if these are the UART pins I am looking for?
  • Which soldering iron should I get for this kind of miniature soldering?
Thank you very much for your help!


Hello almeiras

The UART contacts I am aware of are connected to pins 2 and 7. On the openwrt forum, bmx39 and minhng99 shared photos of their adapters.
https://forum.openwrt.org/t/support-ma5 ... n/48042/24

Restoration of the G-010S-P module is simple. After connecting the adapter, just send the mtd2 and mtd5 firmware from the u-boot level. Our u-boot is factory unlocked. We don't have to jump over obstacles like the owners of the MA5671A module. Remember not to destroy the mtd1 partition that contains the u-boot variables calibrated for this module.

Original firmware 12.09
https://github.com/minhng99/alcatel_luc ... master/mtd

Restoration instructions I copied from here
https://forum.openwrt.org/t/support-ma5 ... n/48042/17
#transfer image mtd2 by Kermit into memory
FALCON => loadb
## Ready for binary (kermit) download to 0x80800000 at 115200 bps...

#to write mtd2(image0)
sf probe 0
sf erase C0000 740000
sf write 80800000 C0000 740000

#transfer image mtd5 by Kermit into memory
FALCON => loadb
## Ready for binary (kermit) download to 0x80800000 at 115200 bps...

#to write mtd5(image1)
sf probe 0
sf erase 800000 740000
sf write 80800000 800000 740000
 
almeiras
just joined
Posts: 5
Joined: Fri Nov 15, 2019 9:16 pm

Re: Usage GPON module SFP in Spain

Tue May 26, 2020 11:39 pm

Great, thank you so much JeanPierre!

I have already ordered a couple of SFP female connectors for the soldering. My Pi Zero and I are looking forward to some UART flashing!
 
BackON
just joined
Posts: 7
Joined: Fri Jan 03, 2020 12:58 pm

Re: Usage GPON module SFP in Spain

Fri May 29, 2020 6:31 pm

Hello

I have another sfp gpon module from Nokia. The model is G-010s-B


Intrrnal photos

Image Image


Running on 192.168.1.10 but i dont know Web user and password but ssh password is ONTUSER/SUGAR2A041. Nmap says runs on 15.05 openwrt



Image Image


i accesed it via ssh.

Image
ONTUSER@easy98035synce1588:/# cat /proc/cpuinfo
system type             : Falcon rev A22
machine                 : EASY98035SYNCE1588 - Lantiq Falcon SFP Stick with Sync       E/1588
processor               : 0
cpu model               : MIPS 34Kc V5.6
BogoMIPS                : 265.98
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 16
extra interrupt vector  : yes
hardware watchpoint     : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0f       fb, 0x0ffb]
isa                     : mips1 mips2 mips32r1 mips32r2
ASEs implemented        : mips16 dsp mt
shadow register sets    : 1
kscratch registers      : 0
package                 : 0
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available
dev:    size   erasesize  name
mtd0: 00040000 00010000 "uboot"
mtd1: 00080000 00010000 "uboot_env"
mtd2: 00c00000 00010000 "linux"
mtd3: 0013cedb 00010000 "kernel"
mtd4: 00ac3125 00010000 "rootfs"
mtd5: 00600000 00010000 "rootfs_data"
mtd6: 00c00000 00010000 "image1"
mtd7: 00200000 00010000 "configfs"
mtd8: 00300000 00010000 "logfs"
mtd9: 00200000 00010000 "extfs"
mtd10: 00010000 00010000 "ri"
mtd11: 00010000 00010000 "sfp"
mtd12: 00010000 00010000 "ribackup"
mtd13: 00010000 00010000 "reserve"
Uci Config
 uci: Entry not found
dhcp.odhcpd=odhcpd
dhcp.odhcpd.maindhcp='0'
dhcp.odhcpd.leasefile='/tmp/hosts/odhcpd'
dhcp.odhcpd.leasetrigger='/usr/sbin/odhcpd-update'
dropbear.@dropbear[0]=dropbear
dropbear.@dropbear[0].PasswordAuth='on'
dropbear.@dropbear[0].RootPasswordAuth='on'
dropbear.@dropbear[0].Port='22'
goi_config.global=goi
goi_config.global.CalibrationTimestamp='2018-04-13T10:08; script V7.6.4; OCAL V7.6.1; FW V7.6.1'
goi_config.ranges=goi
goi_config.temperature_tables=goi
goi_config.dcdc_apd=goi
goi_config.transmitter=goi
goi_config.transmit_power=goi
goi_config.transmit_power.P1_0='3387'
goi_config.transmit_power.P0_0='170'
goi_config.monitor=goi
goi_config.monitor.MPD_Calibration_PL0='3'
goi_config.monitor.MPD_Calibration_PL1='3'
goi_config.monitor.TiaGain_PL1='1'
goi_config.monitor.TiaGain_PL0='1'
goi_config.monitor.TiaGain_PL2='3'
goi_config.monitor.MPD_Calibration_PL2='2'
goi_config.monitor.Dcalref0_PL0='3050'
goi_config.monitor.Dcalref1_PL0='3146'
goi_config.monitor.Dcalref0_PL1='3047'
goi_config.monitor.Dcalref1_PL1='3118'
goi_config.monitor.Dcalref0_PL2='1260'
goi_config.monitor.Dcalref1_PL2='1254'
goi_config.monitor.Dref0_PL0='184'
goi_config.monitor.Dref1_PL0='1563'
goi_config.monitor.MPDxt_PL0='0.778036673083'
goi_config.monitor.Imodref_PL0='34.6762215795'
goi_config.monitor.Dref0_PL1='117'
goi_config.monitor.Dref1_PL1='938'
goi_config.monitor.MPDxt_PL1='0.933644007699'
goi_config.monitor.Imodref_PL1='19.6178810304'
goi_config.monitor.Dref0_PL2='258'
goi_config.monitor.Dref1_PL2='1669'
goi_config.monitor.MPDxt_PL2='4.0717252558'
goi_config.monitor.Imodref_PL2='9.80894051519'
goi_config.measurement=goi
goi_config.measurement.Tscal_ref='0.484715133905'
goi_config.measurement.RSSI_1490parabolic_ref='0'
goi_config.measurement.RSSI_1490dark_ref='0.0008544921875'
goi_config.measurement.RSSI_1490scal_ref='0.84979253112'
goi_config.omu=goi
goi_config.bosa=goi
goi_config.fcsi=goi
goi_config.fcsi.GVS='0xf653'
goi_defaults.global=goi
goi_defaults.global.CalibrationTimestamp='OCAL V7.5.0'
goi_defaults.global.TempMonitorInterval='1000'
goi_defaults.global.TempMonitorThreshold_MPDcorrection='3'
goi_defaults.global.LaserAgeStoreCycle='43200'
goi_defaults.global.Polarity_Rx='0'
goi_defaults.global.Polarity_Bias='1'
goi_defaults.global.Polarity_Mod='1'
goi_defaults.global.Temp_IntCorr_AlarmYellow_Set='390'
goi_defaults.global.Temp_IntCorr_AlarmYellow_Clear='370'
goi_defaults.global.Temp_IntCorr_AlarmRed_Set='420'
goi_defaults.global.Temp_IntCorr_AlarmRed_Clear='400'
goi_defaults.global.TransmitLevelCheckInterval='1000'
goi_defaults.global.OpticMode='undefined'
goi_defaults.ranges=goi
goi_defaults.ranges.TableTemp_ExtCorr_Min='223'
goi_defaults.ranges.TableTemp_ExtCorr_Max='423'
goi_defaults.ranges.TableTemp_ExtNom_Min='200'
goi_defaults.ranges.TableTemp_ExtNom_Max='450'
goi_defaults.ranges.TableTemp_IntCorr_Min='223'
goi_defaults.ranges.TableTemp_IntCorr_Max='473'
goi_defaults.ranges.TableTemp_IntNom_Min='200'
goi_defaults.ranges.TableTemp_IntNom_Max='450'
goi_defaults.ranges.Ibias_Max='60'
goi_defaults.ranges.Imod_Max='80'
goi_defaults.ranges.Iavg_Max='200'
goi_defaults.ranges.IbiasImod_Max='120'
goi_defaults.ranges.CInt_Bias_Max='7'
goi_defaults.ranges.CInt_Mod_Max='7'
goi_defaults.ranges.VAPD_Min='20'
goi_defaults.ranges.VAPD_Max='60'
goi_defaults.ranges.Power_Measure_Min='0.30'
goi_defaults.ranges.Overcurrent_Ibias_Thr='60'
goi_defaults.ranges.Overcurrent_Imod_Thr='80'
goi_defaults.ranges.Overcurrent_IbiasImod_Thr='100'
goi_defaults.temperature_tables=goi
goi_defaults.temperature_tables.Tci_Ith_low='50'
goi_defaults.temperature_tables.Tci_Ith_high='40'
goi_defaults.temperature_tables.Tci_SE_low='-200'
goi_defaults.temperature_tables.Tci_SE_high='-100'
goi_defaults.temperature_tables.Tcd_Ith_low='30'
goi_defaults.temperature_tables.Tcd_Ith_high='30'
goi_defaults.temperature_tables.Tcd_SE_low='30'
goi_defaults.temperature_tables.Tcd_SE_high='30'
goi_defaults.temperature_tables.VAPD_scal_ref_low='0.09'
goi_defaults.temperature_tables.VAPD_scal_ref_high='0.09'
goi_defaults.dcdc_apd=goi
goi_defaults.dcdc_apd.VAPD_enable='0'
goi_defaults.dcdc_apd.Rdiv_low='10000'
goi_defaults.dcdc_apd.Rdiv_high='294000'
goi_defaults.dcdc_apd.VAPD_offset='3.0'
goi_defaults.dcdc_apd.VAPD_ext_inductivity='12'
goi_defaults.dcdc_apd.VAPD_ext_supply='3.30'
goi_defaults.dcdc_apd.VAPD_efficiency='50'
goi_defaults.dcdc_apd.VAPD_current_limit='2.00'
goi_defaults.transmitter=goi
goi_defaults.transmitter.TxEnableDelay='8'
goi_defaults.transmit_power=goi
goi_defaults.transmit_power.P0_0='180'
goi_defaults.transmit_power.P1_0='3820'
goi_defaults.transmit_power.P0_1='90'
goi_defaults.transmit_power.P1_1='1910'
goi_defaults.transmit_power.P0_2='45'
goi_defaults.transmit_power.P1_2='955'
goi_defaults.monitor=goi
goi_defaults.monitor.TiaGain_PL0='2'
goi_defaults.monitor.TiaGain_PL1='3'
goi_defaults.monitor.TiaGain_PL2='3'
goi_defaults.monitor.MPD_Calibration_PL0='3'
goi_defaults.monitor.MPD_Calibration_PL1='2'
goi_defaults.monitor.MPD_Calibration_PL2='2'
goi_defaults.monitor.ImodScalCorr_PL0='1.0'
goi_defaults.monitor.ImodScalCorr_PL1='1.0'
goi_defaults.monitor.ImodScalCorr_PL2='1.0'
goi_defaults.monitor.Dcalref0_PL0='3930'
goi_defaults.monitor.Dcalref1_PL0='4000'
goi_defaults.monitor.Dcalref0_PL1='1160'
goi_defaults.monitor.Dcalref1_PL1='1230'
goi_defaults.monitor.Dcalref0_PL2='1160'
goi_defaults.monitor.Dcalref1_PL2='1230'
goi_defaults.monitor.Dref0_PL0='180'
goi_defaults.monitor.Dref1_PL0='1910'
goi_defaults.monitor.Dref0_PL1='280'
goi_defaults.monitor.Dref1_PL1='2540'
goi_defaults.monitor.Dref0_PL2='200'
goi_defaults.monitor.Dref1_PL2='1270'
goi_defaults.monitor.PowerSave='1'
goi_defaults.monitor.rogue_onu_interburst='0'
goi_defaults.monitor.RogueAlarm_Threshold_P0='20'
goi_defaults.monitor.RogueAlarm_Threshold_P1='120'
goi_defaults.monitor.MPDxt_PL0='-1'
goi_defaults.monitor.MPDxt_PL1='-1'
goi_defaults.monitor.MPDxt_PL2='-1'
goi_defaults.monitor.Imodref_PL0='36.0'
goi_defaults.monitor.Imodref_PL1='18.0'
goi_defaults.monitor.Imodref_PL2='9.0'
goi_defaults.measurement=goi
goi_defaults.measurement.Tscal_ref='0.550'
goi_defaults.measurement.pnR='1.0'
goi_defaults.measurement.pnIsource='1'
goi_defaults.measurement.Supply_voltage_Enable='1'
goi_defaults.measurement.RSSI_1550_Enable='0'
goi_defaults.measurement.RF_1550_Enable='0'
goi_defaults.measurement.DAC_1550_Enable='0'
goi_defaults.measurement.RSSI_1490mode='1'
goi_defaults.measurement.RSSI_1490shunt_res='4990'
goi_defaults.measurement.RSSI_1490dark_corr='1.20'
goi_defaults.measurement.RSSI_1550vref='1'
goi_defaults.measurement.RF_1550vref='1'
goi_defaults.measurement.RSSI_1490scal_ref='0.07'
goi_defaults.measurement.RSSI_1550scal_ref='0.10'
goi_defaults.measurement.RF_1550scal_ref='0.10'
goi_defaults.measurement.RSSI_1490parabolic_ref='0.08'
goi_defaults.measurement.RSSI_1490dark_ref='0.002'
goi_defaults.measurement.RSSI_autolevel='0'
goi_defaults.measurement.RSSI_1490threshold_low='40'
goi_defaults.measurement.RSSI_1490threshold_high='70'
goi_defaults.measurement.Tbosa_source='1'
goi_defaults.measurement.Vdd_scal='0.5'
goi_defaults.measurement.V0K_Tref='1200'
goi_defaults.omu=goi
goi_defaults.omu.SignalDetectAvailable='1'
goi_defaults.omu.SignalDetectPort='2'
goi_defaults.omu.LolThreshold_set='20'
goi_defaults.omu.LolThreshold_clear='20'
goi_defaults.omu.LaserSignalSingleEnded='1'
goi_defaults.bosa=goi
goi_defaults.bosa.LoopMode='2'
goi_defaults.bosa.LolThreshold_set='20'
goi_defaults.bosa.LolThreshold_clear='20'
goi_defaults.bosa.LosThreshold_set='0.0005'
goi_defaults.bosa.LosThreshold_clear='0.0010'
goi_defaults.bosa.RxOverloadThreshold='0.2000'
goi_defaults.bosa.CInt_Bias_init='2'
goi_defaults.bosa.CInt_Mod_init='2'
goi_defaults.bosa.PICtrl='0x00004049'
goi_defaults.bosa.UpdateThreshold_Bias='2'
goi_defaults.bosa.UpdateThreshold_Mod='2'
goi_defaults.bosa.LearningThreshold_Bias='99'
goi_defaults.bosa.LearningThreshold_Mod='99'
goi_defaults.bosa.StableThreshold_Bias='2'
goi_defaults.bosa.StableThreshold_Mod='2'
goi_defaults.bosa.ResetThreshold_Bias='70'
goi_defaults.bosa.ResetThreshold_Mod='70'
goi_defaults.fcsi=goi
goi_defaults.fcsi.GVS='0xF653'
gpon.ploam=gpon
gpon.ploam.nPassword='0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20'
gpon.ploam.nT01='11000'
gpon.ploam.nT02='100'
gpon.ploam.nRogueMsgIdUpstreamReset='255'
gpon.ploam.nRogueMsgRepeatUpstreamReset='3'
gpon.ploam.nRogueMsgIdDeviceReset='255'
gpon.ploam.nRogueMsgRepeatDeviceReset='3'
gpon.ploam.nRogueEnable='0'
gpon.gtc=gpon
gpon.gtc.bDlosEnable='0'
gpon.gtc.bDlosInversion='0'
gpon.gtc.nDlosWindowSize='0'
gpon.gtc.nDlosTriggerThreshold='0'
gpon.gtc.ePower='0'
gpon.gtc.nLaserGap='0'
gpon.gtc.nLaserOffset='0'
gpon.gtc.nLaserEnEndExt='0'
gpon.gtc.nLaserEnStartExt='0'
gpon.gtc.nDyingGaspHyst='0'
gpon.gtc.nDyingGaspMsg='0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00'
gpon.gtc.nDyingGaspEnable='0'
gpon.gpe=gpon
gpon.gpe.nPeNumber='6'
gpon.gpe.nDSCP_MappingRule='0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 '
ieee_1588.ptp_sync=ieee_1588
ieee_1588.ptp_sync.delay_mechanism='-E'
ieee_1588.ptp_sync.network_transport='-2'
ieee_1588.ptp_sync.timestamping='-H'
ieee_1588.ptp_sync.cfg_file='/etc/g_8275_1.conf'
ieee_1588.ptp_sync.interface='lct0'
ieee_1588.ptp_sync.log_level='6'
ieee_1588.tod2phc=ieee_1588
ieee_1588.tod2phc.xpectd_mc_name='Intel PON TOD'
ieee_1588.tod2phc.xpectd_sc_name='Intel F24S'
ieee_1588.tod2phc.master_clock='/dev/ptp0'
ieee_1588.tod2phc.slave_clock='/dev/ptp1'
ieee_1588.tod2phc.offset='0'
ieee_1588.tod2phc.time_thr='20'
ieee_1588.tod2phc.sync_offset='-14'
ieee_1588.tod2phc.log_level='6'
ieee_1588.tod2phc.threshold='0.00002'
ieee_1588.tod2ktimer=ieee_1588
ieee_1588.tod2ktimer.xpectd_phc_name='Intel PON TOD'
ieee_1588.tod2ktimer.auto_cfg='-a'
ieee_1588.tod2ktimer.synch_sys_clk='-r'
ieee_1588.tod2ktimer.phc_clk='/dev/ptp0'
ieee_1588.tod2ktimer.domain_num='24'
ieee_1588.tod2ktimer.offset='0'
ieee_1588.tod2ktimer.log_level='6'
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='auto'
network.lct=interface
network.lct.ifname='lct0'
network.lct.netmask='255.255.255.0'
network.lct.proto='static'
network.lct.macaddr='ac:9a:96:00:00:00'
network.lct.gateway='192.168.2.1'
network.lct.ipaddr='192.168.1.10'
network.host=interface
network.host.ifname='host'
network.host.proto='static'
network.host.ipaddr='0.0.0.0'
network.host.netmask='0.0.0.0'
network.host.macaddr='ac:9a:96:00:02:00'
network.host6=interface
network.host6.ifname='@host'
network.host6.proto='static'
nmea.message=nmea
nmea.message.nmea_format='1'
nmea.message.time_offset='19'
omci.default=omci
omci.default.mib_file='/etc/mibs/data_2g_8q.ini'
omci.default.status_file='/tmp/omci_status'
omci.iphost=omci
omci.iphost.enabled='1'
omci.iphost.committed='32000 2048'
omci.iphost.peak='32000 2048'
omci.iphost.color_aware='0'
omci.iphost.mode='0'
rpcd.@login[0]=login
rpcd.@login[0].username='root'
rpcd.@login[0].password='$p$root'
rpcd.@login[0].read='*'
rpcd.@login[0].write='*'
sfp_eeprom.default=sfp_eeprom
sfp_eeprom.default.eeprom='0'
sfp_eeprom.default.vendor_name='Lantiq'
sfp_eeprom.default.vendor_partno='Part Number'
sfp_eeprom.default.vendor_rev='0000'
sfp_eeprom.default.vendor_oui='AC:9A:96'
sfp_eeprom.default.serial_no='no serial number'
sfp_eeprom.default.datecode='150414'
sfp_eeprom.default.addr_eeprom_0='0x80'
sfp_eeprom.default.addr_eeprom_1='0x51'
sfp_pins.@pin[0]=pin
sfp_pins.@pin[0].name='tx_fault'
sfp_pins.@pin[0].pin='2'
sfp_pins.@pin[0].restriction='ASC_TX'
sfp_pins.@pin[1]=pin
sfp_pins.@pin[1].name='tx_disable'
sfp_pins.@pin[1].pin='1'
sfp_pins.@pin[2]=pin
sfp_pins.@pin[2].name='los'
sfp_pins.@pin[2].pin='3'
sfp_pins.@pin[3]=pin
sfp_pins.@pin[3].name='mod_def'
sfp_pins.@pin[3].pin='41'
synce.ethernet=synce
synce.ethernet.nSyncE_Mode='1'
synce.ethernet.bSyncE_SGMII_Squelch='0'
synce_pins.@pin[0]=pin
synce_pins.@pin[0].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[0].pin='43'
synce_pins.@pin[1]=pin
synce_pins.@pin[1].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[1].pin='44'
synce_pins.@pin[2]=pin
synce_pins.@pin[2].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[2].pin='43'
synce_pins.@pin[3]=pin
synce_pins.@pin[3].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[3].pin='44'
synce_pins.@pin[4]=pin
synce_pins.@pin[4].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[4].pin='43'
synce_pins.@pin[5]=pin
synce_pins.@pin[5].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[5].pin='44'
synce_pins.@pin[6]=pin
synce_pins.@pin[6].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[6].pin='43'
synce_pins.@pin[7]=pin
synce_pins.@pin[7].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[7].pin='44'
synce_pins.@pin[8]=pin
synce_pins.@pin[8].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[8].pin='43'
synce_pins.@pin[9]=pin
synce_pins.@pin[9].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[9].pin='44'
synce_pins.@pin[10]=pin
synce_pins.@pin[10].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[10].pin='43'
synce_pins.@pin[11]=pin
synce_pins.@pin[11].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[11].pin='44'
synce_pins.@pin[12]=pin
synce_pins.@pin[12].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[12].pin='43'
synce_pins.@pin[13]=pin
synce_pins.@pin[13].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[13].pin='44'
synce_pins.@pin[14]=pin
synce_pins.@pin[14].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[14].pin='43'
synce_pins.@pin[15]=pin
synce_pins.@pin[15].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[15].pin='44'
synce_pins.@pin[16]=pin
synce_pins.@pin[16].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[16].pin='43'
synce_pins.@pin[17]=pin
synce_pins.@pin[17].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[17].pin='44'
synce_pins.@pin[18]=pin
synce_pins.@pin[18].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[18].pin='43'
synce_pins.@pin[19]=pin
synce_pins.@pin[19].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[19].pin='44'
synce_pins.@pin[20]=pin
synce_pins.@pin[20].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[20].pin='43'
synce_pins.@pin[21]=pin
synce_pins.@pin[21].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[21].pin='44'
synce_pins.@pin[22]=pin
synce_pins.@pin[22].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[22].pin='43'
synce_pins.@pin[23]=pin
synce_pins.@pin[23].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[23].pin='44'
synce_pins.@pin[24]=pin
synce_pins.@pin[24].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[24].pin='43'
synce_pins.@pin[25]=pin
synce_pins.@pin[25].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[25].pin='44'
synce_pins.@pin[26]=pin
synce_pins.@pin[26].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[26].pin='43'
synce_pins.@pin[27]=pin
synce_pins.@pin[27].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[27].pin='44'
synce_pins.@pin[28]=pin
synce_pins.@pin[28].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[28].pin='43'
synce_pins.@pin[29]=pin
synce_pins.@pin[29].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[29].pin='44'
synce_pins.@pin[30]=pin
synce_pins.@pin[30].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[30].pin='43'
synce_pins.@pin[31]=pin
synce_pins.@pin[31].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[31].pin='44'
synce_pins.@pin[32]=pin
synce_pins.@pin[32].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[32].pin='43'
synce_pins.@pin[33]=pin
synce_pins.@pin[33].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[33].pin='44'
synce_pins.@pin[34]=pin
synce_pins.@pin[34].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[34].pin='43'
synce_pins.@pin[35]=pin
synce_pins.@pin[35].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[35].pin='44'
synce_pins.@pin[36]=pin
synce_pins.@pin[36].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[36].pin='43'
synce_pins.@pin[37]=pin
synce_pins.@pin[37].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[37].pin='44'
synce_pins.@pin[38]=pin
synce_pins.@pin[38].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[38].pin='43'
synce_pins.@pin[39]=pin
synce_pins.@pin[39].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[39].pin='44'
synce_pins.@pin[40]=pin
synce_pins.@pin[40].name='nGPIO_ExtPLL_LD'
synce_pins.@pin[40].pin='43'
synce_pins.@pin[41]=pin
synce_pins.@pin[41].name='nGPIO_ExtPLL_CF'
synce_pins.@pin[41].pin='44'
system.@system[0]=system
system.@system[0].timezone='UTC'
system.@system[0].hostname='easy98035synce1588'
system.ntp=timeserver
system.ntp.server='0.openwrt.pool.ntp.org' '1.openwrt.pool.ntp.org' '2.openwrt.pool.ntp.org' '3.openwrt.pool.ntp.org'
system.ntp.enabled='1'
system.ntp.enable_server='0' 
 
BackON
just joined
Posts: 7
Joined: Fri Jan 03, 2020 12:58 pm

Re: Usage GPON module SFP in Spain

Fri May 29, 2020 9:29 pm

dmesg log
ONTUSER@easy98035synce1588:/# dmesg
[    0.000000] Linux version 3.18.44 (buildmgr@AONT27) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 15.05_ltq) ) #1 Mon Aug 21 17:16:12 CST 2017
[    0.000000] SoC: Falcon rev A22
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is EASY98035SYNCE1588 - Lantiq Falcon SFP Stick with SyncE/1588
[    0.000000] e=memsize=64
[    0.000000] e=initrd_start=0xA0000000
[    0.000000] e=initrd_size=0x0
[    0.000000] e=flash_start=0x00000000
[    0.000000] e=flash_size=0x0
[    0.000000] e=ethaddr=ac:9a:96:00:00:00
[    0.000000] MEMSIZE = 67108864
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 03f00000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03efffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03efffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03efffff]
[    0.000000] On node 0 totalpages: 16128
[    0.000000] free_area_init_node: node 0, pgdat 80361d50, node_mem_map 81009840
[    0.000000]   Normal zone: 126 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16128 pages, LIFO batch:3
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16002
[    0.000000] Kernel command line: rootfstype=squashfs,jffs2 ip=192.168.1.10:192.168.1.100:192.168.2.1::::off ethaddr=ac:9a:96:00:00:00 machtype=EASY98035SYNCE1588 vpe1_load_addr=0x83f00000 vpe1_mem=1M mem=63M mtdparts=sflash:256k(uboot)ro,512k(uboot_env),12288k(linux),12288k(image1),2048k(configfs),3072k(logfs),2048k(extfs),64k(ri),64k(sfp),64k(ribackup),64k(reserve) quiet console= console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00018252
[    0.000000] Readback ErrCtl register=00018252
[    0.000000] Memory: 59856K/64512K available (2858K kernel code, 145K rwdata, 564K rodata, 192K init, 199K bss, 4656K reserved)
[    0.000000] NR_IRQS:328
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 400MHz
[    0.032000] Calibrating delay loop... 265.98 BogoMIPS (lpj=531968)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.036000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-falcon pinctrl: Init done
[    0.064000] FALC(tm) ON GPIO Driver, (C) 2012 Lantiq Deutschland Gmbh
[    0.068000] Switched to clocksource MIPS
[    0.072000] NET: Registered protocol family 2
[    0.072000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.072000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.072000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.072000] TCP: reno registered
[    0.072000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.072000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.072000] NET: Registered protocol family 1
[    0.072000] RPC: Registered named UNIX socket transport module.
[    0.072000] RPC: Registered udp transport module.
[    0.072000] RPC: Registered tcp transport module.
[    0.072000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.072000] EASY98000 LED driver, Version 1.0.1 (c) Copyright 2013, Lantiq Deutschland GmbH
[    0.072000] Wired TLB entries for Linux read_c0_wired() = 0
[    0.072000] config3 0x2425 MT 1
[    0.072000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[    0.072000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[    0.076000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.076000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.076000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.076000] msgmni has been set to 116
[    0.080000] io scheduler noop registered
[    0.080000] io scheduler deadline registered (default)
[    0.080000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 104, base_baud = 0) is a lantiq,asc
[    0.080000] console [ttyLTQ0] enabled
[    0.080000] bootconsole [early0] disabled
[    0.116000] m25p80 spi0.0: found mx25l25635e, expected s25fl129p0
[    0.116000] m25p80 spi0.0: mx25l25635e (32768 Kbytes)
[    0.116000] 11 cmdlinepart partitions found on MTD device sflash
[    0.116000] Creating 11 MTD partitions on "sflash":
[    0.116000] 0x000000000000-0x000000040000 : "uboot"
[    0.116000] 0x000000040000-0x0000000c0000 : "uboot_env"
[    0.116000] 0x0000000c0000-0x000000cc0000 : "linux"
[    0.144000] 2 uimage-fw partitions found on MTD device linux
[    0.144000] 0x0000000c0000-0x0000001fcedb : "kernel"
[    0.144000] 0x0000001fcedb-0x000000cc0000 : "rootfs"
[    0.144000] mtd: device 4 (rootfs) set to be root filesystem
[    0.144000] 1 squashfs-split partitions found on MTD device rootfs
[    0.144000] 0x0000006c0000-0x000000cc0000 : "rootfs_data"
[    0.148000] 0x000000cc0000-0x0000018c0000 : "image1"
[    0.148000] 0x0000018c0000-0x000001ac0000 : "configfs"
[    0.148000] 0x000001ac0000-0x000001dc0000 : "logfs"
[    0.152000] 0x000001dc0000-0x000001fc0000 : "extfs"
[    0.152000] 0x000001fc0000-0x000001fd0000 : "ri"
[    0.152000] 0x000001fd0000-0x000001fe0000 : "sfp"
[    0.156000] 0x000001fe0000-0x000001ff0000 : "ribackup"
[    0.156000] 0x000001ff0000-0x000002000000 : "reserve"
[    0.156000] wdt 1f8803f0.watchdog: Init done
[    0.160000] TCP: cubic registered
[    0.160000] NET: Registered protocol family 17
[    0.160000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.160000] 8021q: 802.1Q VLAN Support v1.8
[   12.212000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[   12.216000] Freeing unused kernel memory: 192K (80380000 - 803b0000)
[   14.852000] init: Console is alive
[   16.032000] pps_core: LinuxPPS API ver. 1 registered
[   16.032000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[   16.032000] PTP clock support registered
[   16.944000] init: - preinit -
[   17.552000] jffs2: notice: (293) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   17.608000] jffs2: notice: (295) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   18.480000] random: mktemp urandom read with 72 bits of entropy available
[   21.728000] procd: - early -
[   22.440000] procd: - ubus -
[   23.448000] procd: - init -
[   24.856000] g_board_hw_version 87
[   24.856000] ri module install
[   24.860000] IFXOS, Version 1.6.9 (c) Copyright 2009, Lantiq Deutschland GmbH
[   24.948000] NET: Registered protocol family 10
[   24.956000] i2c /dev entries driver
[   24.964000] Custom GPIO-based I2C driver version 0.1.1
[   24.964000] i2c-gpio i2c-gpio.0: using pins 37 (SDA) and 38 (SCL)
[   24.968000] i2c_driver_major is 247
[   24.968000] This board has 1 i2c bus, 0 bus is expanded by PCA9554i2c driver install.
[   25.048000] kigmp: Unknown symbol gpe_short_fwd_mac_mc_port_delete (err 0)
[   25.048000] kigmp: Unknown symbol onu_mod_open (err 0)
[   25.048000] kigmp: Unknown symbol netdev_rem_igmp_snooping_rx_callback (err 0)
[   25.048000] kigmp: Unknown symbol gpe_short_fwd_ipv4_mc_filter_add (err 0)
[   25.048000] kigmp: Unknown symbol netdev_set_igmp_snooping_rx_callback (err 0)
[   25.048000] kigmp: Unknown symbol onu_mod_close (err 0)
[   25.048000] kigmp: Unknown symbol gpe_long_fwd_ipv6_mc_filter_add (err 0)
[   25.048000] kigmp: Unknown symbol gpe_ext_vlan_get (err 0)
[   25.048000] kigmp: Unknown symbol gpe_table_entry_get (err 0)
[   25.048000] kigmp: Unknown symbol gpe_ext_vlan_set (err 0)
[   25.048000] kigmp: Unknown symbol gpe_short_fwd_ipv4_mc_port_add (err 0)
[   25.048000] kigmp: Unknown symbol gpe_long_fwd_ipv6_mc_port_add (err 0)
[   25.048000] kigmp: Unknown symbol gpe_short_fwd_mac_mc_port_add (err 0)
[   25.048000] kigmp: Unknown symbol gpe_short_fwd_ipv4_mc_port_delete (err 0)
[   25.048000] kigmp: Unknown symbol gpe_long_fwd_ipv6_mc_port_delete (err 0)
[   25.052000] F24S Driver, Version 1.2.0
[   25.124000] Intel PON Chipset Optic Driver, version 7.6.2.0
[   25.132000] GPON SFP I2C Slave Driver, Version 2.4.0 (c) Copyright 2015, Lantiq Beteiligungs-GmbH & Co. KG
[   25.236000] [sfp_i2c] vpe code <sfp_i2c_vpe.bin> with size <3352 bytes> loaded!
[   25.236000] VPE loader: VPE1 running successfully
[   25.252000] kigmp: Unknown symbol gpe_short_fwd_mac_mc_port_delete (err 0)
[   25.252000] kigmp: Unknown symbol onu_mod_open (err 0)
[   25.252000] kigmp: Unknown symbol netdev_rem_igmp_snooping_rx_callback (err 0)
[   25.252000] kigmp: Unknown symbol gpe_short_fwd_ipv4_mc_filter_add (err 0)
[   25.252000] kigmp: Unknown symbol netdev_set_igmp_snooping_rx_callback (err 0)
[   25.252000] kigmp: Unknown symbol onu_mod_close (err 0)
[   25.252000] kigmp: Unknown symbol gpe_long_fwd_ipv6_mc_filter_add (err 0)
[   25.252000] kigmp: Unknown symbol gpe_ext_vlan_get (err 0)
[   25.252000] kigmp: Unknown symbol gpe_table_entry_get (err 0)
[   25.252000] kigmp: Unknown symbol gpe_ext_vlan_set (err 0)
[   25.252000] kigmp: Unknown symbol gpe_short_fwd_ipv4_mc_port_add (err 0)
[   25.252000] kigmp: Unknown symbol gpe_long_fwd_ipv6_mc_port_add (err 0)
[   25.252000] kigmp: Unknown symbol gpe_short_fwd_mac_mc_port_add (err 0)
[   25.252000] kigmp: Unknown symbol gpe_short_fwd_ipv4_mc_port_delete (err 0)
[   25.252000] kigmp: Unknown symbol gpe_long_fwd_ipv6_mc_port_delete (err 0)
[   25.636000] watchdog: add to proc fs ok
[   25.636000] Intel PON Chipset Base Driver, Version 7.6.2.0
[   25.660000] Intel PON Chipset Ethernet Driver, Version 7.6.2.0
[   25.664000] Registered Intel PON TOD PTP clock
[   25.700000] igmpdrv k_igmp_drv_init
[   25.700000] igmpmap IgmpMapFilterConfig IPTV Filter mode changed from 1 to 5
[   25.708000] igmpdb igmpdbthreadinit Enter DB create the thread.
[   25.724000] [onu] Now netdev have set Snooping Call Back.
[   25.724000] successfully insert igmp dev module
[   32.860000] random: nonblocking pool is initialized
[   41.888000] [onu] GPHY Firmware loaded into RAM (phy11g.bin)
[   42.416000] [onu] PE[255] firmware loaded v15.9.8.4
[   44.920000] [f24s]: Registered Intel F24S PTP clock
[   44.920000] libphy: Falcon MDIO: probed
[   44.936000] IPv6: ADDRCONF(NETDEV_UP): host: link is not ready
[   44.988000] [f24s]: lct0: Intel F24S Switch driver attached (irq=10).
[   44.996000] [onu_netdev]: onu_netdev_probe: connect to phy at falcon_mdio:1f
[   45.092000] IPv6: ADDRCONF(NETDEV_UP): lct0: link is not ready
[   45.996000] IPv6: ADDRCONF(NETDEV_CHANGE): lct0: link becomes ready
[   47.776000] IPv6: ADDRCONF(NETDEV_UP): lct0: link is not ready
[   48.068000] IPv6: ADDRCONF(NETDEV_UP): lct0: link is not ready
[   48.996000] IPv6: ADDRCONF(NETDEV_CHANGE): lct0: link becomes ready
[   64.016000] IPv6: ADDRCONF(NETDEV_UP): host: link is not ready
[   64.140000]
[   64.140000] Set board info type = 255
[   64.156000] Reset igmp snooping.
[   65.044000] igmpltq hal_kernel_cfg_mcast_vlan_action  There is no Gemport found for Mulitcast.
[   65.064000] igmpltq Cfg Vlan Action with itf:1 Error.
[   65.068000] igmpltq hal_kernel_cfg_mcast_vlan_action  There is no Gemport found for Mulitcast.
[   65.076000] igmpltq Cfg Vlan Action with itf:2 Error.
[   65.080000] igmpltq hal_kernel_cfg_mcast_vlan_action  There is no Gemport found for Mulitcast.
[   65.100000] igmpltq Cfg Vlan Action with itf:3 Error.
[   65.104000] igmpltq hal_kernel_cfg_mcast_vlan_action  There is no Gemport found for Mulitcast.
[   65.120000] igmpltq Cfg Vlan Action with itf:4 Error.
[   65.124000] igmpltq hal_kernel_cfg_mcast_vlan_action  There is no Gemport found for Mulitcast.
[   65.144000] igmpltq Cfg Vlan Action with itf:5 Error.
[   65.148000] igmpltq hal_kernel_cfg_mcast_vlan_action  There is no Gemport found for Mulitcast.
[   67.956000] get OperatorID=XXXX and start long time light status

fw_printenv
ONTUSER@easy98035synce1588:/# fw_printenv
a0_image=3FE46956AAAA_a0.bin
a2_iaddr=0x1FD0000
a2_image=3FE46956AAAA_a2.bin
act_img_addr=0xBF20003C
addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off
addmisc=setenv bootargs ${bootargs} ethaddr=${ethaddr} machtype=${machtype}  vpe1_load_addr=0x83f00000 vpe1_mem=1M mem=63M ${mtdparts} quiet
addmtdparts0=setenv mtdparts mtdparts=sflash:256k(uboot)ro,512k(uboot_env),12288k(linux),12288k(image1),2048k(configfs),3072k(logfs),2048k(extfs),64k(ri),64k(sfp),64k(ribackup),64k(reserve)
addmtdparts1=setenv mtdparts mtdparts=sflash:256k(uboot)ro,512k(uboot_env),12288k(image0),12288k(linux),2048k(configfs),3072k(logfs),2048k(extfs),64k(ri),64k(sfp),64k(ribackup),64k(reserve)
asc0=3
baudrate=115200
boot_image=run boot_image${c_img};
boot_image0=run kernel0_from_sf flashargs addip addmtdparts0 addmisc && bootm ${ram_addr}
boot_image1=run kernel1_from_sf flashargs addip addmtdparts1 addmisc && bootm ${ram_addr}
boot_image_err=setenv kernel_offs ${kernel0_offs};httpd && setenv image0_is_valid 1
bootargs=rootfstype=squashfs,jffs2 ip=192.168.1.10:192.168.1.100:192.168.2.1::::off ethaddr=ac:9a:96:00:00:00 machtype=EASY98035SYNCE1588 vpe1_load_addr=0x83f00000 vpe1_mem=1M mem=63M mtdparts=sflash:256k(uboot)ro,512k(uboot_env),12288k(linux),12288k(image1),2048k(configfs),3072k(logfs),2048k(extfs),64k(ri),64k(sfp),64k(ribackup),64k(reserve) quiet
bootcmd=run flash_flash
bootdelay=5
c_img=0
commit=0
config_iaddr=0x18C0000
env_offs=0x40000
env_offs_redund=0x80000
ethact=RGMII1
ethaddr=ac:9a:96:00:00:00
ethprime=RGMII1
flash_flash=run select_image boot_image
flashargs=setenv bootargs rootfstype=squashfs,jffs2
gatewayip=192.168.2.1
goi_calibrated=1
goi_config=begin-base64 644 goi_config@H4sIAB8BAAACA+1YS0/bQBDOtfkVW3HICbPvR60eUh4VKi2IpOGAkLVxnGA1@jiPbofTfd5YEMHagVWmjlnouHs/szrevbzzrqAh30nkRhzuTNA4KO5xGwdTm@URZk0TgYguaF+VXrWYJBJOc3T5DqExOp7nQmRQsTRSVtIdzagCzywmYItY4/@9T/39k8fbZeladF6ebKF9lI0SwsUXtrZJELFZYT63+YRikfRrIjHcZS99n2/@7Wxvj7qwQsHp/oGzbKF+lMzR+YcLHx0Wl+h80QWttw/K2U7idAvxzvOLNsPG@Vx6X3DfUU4r5uN1q5O+Q6Cn+P5/6v8h/SRVu+P+P8T9p+P8y+H9l56NgOPpN@7P8J/pd0SRz/hcKy4f9m+D96wH/H8xXbB92TveDd3i3TfTSATwI6HzhCS58z@TzPdEPlF8R8y9h/AcLxWQjzKf8gALUIVkJ5QLBjwnxHW1P8bEdxQ4L/nf5jO@xvHkJgEs1c3ynzIu73IBJ9LxXzX3/81Ie7njCDYfdSbTdGinnfYr90VIZ2jX@TuNhZp3ej5MIVgoK/g7FRG9jvk1Yn+A3WPsoD7N4XqCB8qTHfXS82z1avhAf@HZyt1E77AVbmyo28YiygzogAcJFFy1q02mAUjsIAytNqP4iWJ3FRRNkjnmCe@fnXO26mdkACjDmNalWzY2YjClRhJOouLtNT5IxRGpbUJTo5crKf85IG/H9v3@Nl7ZyTo7fsROf4ADfnrv3wvtFGo2vBogFrjmIysf4XJtPzdwzNXafs5HiF7b@DwZCqFyPd+MTvOS7HyTRFftqgETIhxO/LpYODDdKjZmUimFdanKYpCP3C3M5@Pe5JSCkULhZG1HHdLhBVxwW7YboOSxysYQwuNZDZpDHrYF1Q40mitCYY1rAO@6zZL6DqsWx8pTR0XHNzDiigqqCj3vEeFJsbTWBuOBRHEVI9yZHMgVwJ3+9Lx@ymFv3P8eNy2uuYKOjBlcWqnTXu8wINzguc3sMJ3G4ar9miYjm325jQYZXQvO@DSVarQtXRtbcKEMFHClaGXWaLCqWYZrbimkc5vE9wvtBD2Jej6WAM9HcUhpp@pJFGavIdZGLmDgAcAAA=@====@
gphy0_phyaddr=0
hwconfig=RGMII1:phyaddr=31
image0_addr=0xB00C0000
image0_is_valid=1
image1_addr=0xB0800000
image1_is_valid=1
image_name=g010sb
import_uboot_env=env import -t ${ram_addr} ${filesize}
ipaddr=192.168.1.10
kernel0_from_sf=sf probe 0;sf read ${ram_addr} ${kernel0_offs} ${max_kernel_size}
kernel0_offs=0xC0000
kernel1_from_sf=sf probe 0;sf read ${ram_addr} ${kernel1_offs} ${max_kernel_size}
kernel1_offs=0xCC0000
load_kernel=tftpboot ${ram_addr} ${tftppath}${image_name}-uImage
load_uboot=tftpboot ${ram_addr} ${tftppath}u-boot.img
load_uboot_env=tftp ${ram_addr} ${tftppath}u-boot.env
load_uboot_env_y=loady ${ram_addr}
log_iaddr=0x1AC0000
machtype=EASY98035SYNCE1588
magic_addr=0xBF200038
magic_val=0xDEADBEEF
max_kernel_size=180000
mtdparts=mtdparts=sflash:256k(uboot)ro,512k(uboot_env),12288k(linux),12288k(image1),2048k(configfs),3072k(logfs),2048k(extfs),64k(ri),64k(sfp),64k(ribackup),64k(reserve)
net_nfs=run load_kernel nfsargs addip addmtdparts0 addmisc;bootm ${ram_addr}
netconsole=set stderr nulldev;set stdin nc,serial;set stdout nc,serial
next_active=0
nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath},${nfsoptions}
nfsoptions=rsize=1024,wsize=1024
preboot=gpio clear 100
ram_addr=80F00000
reserve_iaddr=0x1FF0000
reset_uboot_env=env default -f -a; saveenv
ri_hiaddr=0x1FC0000
ri_image=3FE46956AAAA_ri.bin
ri_siaddr=0x1FE0000
save_uboot=sf probe 0;sf erase 0 40000;sf write ${ram_addr} 0 ${filesize}
select_image=if test -n $commit  ; then else setenv commit  _err;saveenv;fi;if test -n $image0_is_valid ; then else setenv image0_is_valid 1;saveenv;fi;if test -n $image1_is_valid ; then else setenv image1_is_valid 0;saveenv;fi;if itest *${magic_addr} == ${magic_val} ; then if itest *${act_img_addr} == 0 ; then setenv next_active 0;fi;if itest *${act_img_addr} == 1 ; then setenv next_active 1;fi;mw ${magic_addr} 0x0;mw ${act_img_addr} 0x0;fi;if test $next_active = -1 ; then setenv c_img $commit;else setenv c_img $next_active;if test $next_active != $commit ;then if test $next_active = 0 ;then setenv next_active 1;setenv image0_is_valid 0;setenv commit 1;else setenv next_active 0;setenv image1_is_valid 0;setenv commit 0;fi;saveenv;fi;fi;exit 0
serverip=192.168.1.100
start_netconsole=if test -n ${ncip}; then echo 'check for netconsole'; if ping ${ncip}; then run netconsole; echo 'netconsole enabled'; fi; fi
stderr=serial
stdin=serial
stdout=serial
update_A0=gpio clear 102;tftpboot ${ram_addr} ${tftppath}${a0_image};eeprom write 50 ${ram_addr} 0 ${filesize}
update_A2=tftpboot ${ram_addr} ${tftppath}${a2_image};sf probe 0;sf erase ${a2_iaddr} +${filesize};sf write ${ram_addr} ${a2_iaddr} ${filesize}
update_configfs=tftpboot ${ram_addr} ${tftppath}configfs.image;sf probe 0;sf erase ${config_iaddr} +${filesize};sf write ${ram_addr} ${config_iaddr} ${filesize}
update_image0=tftpboot ${ram_addr} ${tftppath}${image_name}-squashfs.image;sf probe 0;sf erase ${kernel0_offs} +${filesize};sf write ${ram_addr} ${kernel0_offs} ${filesize}
update_image1=tftpboot ${ram_addr} ${tftppath}${image_name}-squashfs.image;sf probe 0;sf erase ${kernel1_offs} +${filesize};sf write ${ram_addr} ${kernel1_offs} ${filesize}
update_logfs=tftpboot ${ram_addr} ${tftppath}logfs.image;sf probe 0;sf erase ${log_iaddr} +${filesize};sf write ${ram_addr} ${log_iaddr} ${filesize}
update_openwrt=run update_system
update_ri=tftpboot ${ram_addr} ${tftppath}${ri_image};sf probe 0;sf erase ${ri_hiaddr} +${filesize};sf write ${ram_addr} ${ri_hiaddr} ${filesize};sf erase ${ri_siaddr} +${filesize};sf write ${ram_addr} ${ri_siaddr} ${filesize}
update_system=run update_image0 && setenv commit 0 && setenv image0_is_valid 1 && saveenv
update_uboot=run load_uboot && run save_uboot
update_uboot_env=run load_uboot_env && run import_uboot_env && saveenv
update_uboot_env_y=run load_uboot_env_y && run import_uboot_env && saveenv
update_uboot_y=loady ${ram_addr} && run save_uboot
ver=U-Boot 2015.04-lantiq-gpon-1.3.7.1 (Aug 21 2017 - 17:12:42)
boot_fail=0
maybe can be compatible with
https://downloads.openwrt.org/releases/ ... pgrade.bin
 
BackON
just joined
Posts: 7
Joined: Fri Jan 03, 2020 12:58 pm

Re: Usage GPON module SFP in Spain

Fri May 29, 2020 10:12 pm

Finally i got to the web acess to G-010S-B module user adminadmin password ALC#FGU

this is the web page only i can change SLID and password. all other command works like the g-010s-p tomorrow im going to test it in my gpon line

Image
 
BackON
just joined
Posts: 7
Joined: Fri Jan 03, 2020 12:58 pm

Re: Usage GPON module SFP in Spain

Sat May 30, 2020 3:35 pm

Hi again

G-010s-b doesnt work on ftth in spain maybe the missing synce? I going to try to disable it in the firmware and check it again.

Any suggestions?
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Mon Jun 08, 2020 10:07 pm

There have been several reports about new modules with Realtek chips: Ubiquiti UFiber-Instant, V-Solutions - V2801F and many more. I've updated my list of GPON modules.
viewtopic.php?f=3&t=116364&p=771961#p771961

Does anyone know the difference between RTL8672 and RTL9601C. I suppose RTL8672 is the main processor and RTL9601C is dedicated to GPON processing. All clones of modules with Realtek chip have the similar partition layout.

Ubiquiti UFiber-Instant
# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00040000 00001000 "boot"
mtd1: 00002000 00001000 "env"
mtd2: 00002000 00001000 "env2"
mtd3: 0003c000 00001000 "config"
mtd4: 00300000 00001000 "k0"
mtd5: 004b0000 00001000 "r0"
mtd6: 00300000 00001000 "k1"
mtd7: 004b0000 00001000 "r1"
mtd8: 00010000 00001000 "hw"
mtd9: 00010000 00001000 "sec"
mtd10: 00001000 00001000 "Partition_010"
mtd11: 00001000 00001000 "Partition_011"
mtd12: 00300000 00001000 "linux"
mtd13: 004b0000 00001000 "rootfs"


Brief datasheet for V-SOL V2801F listed the RTL9601C as the main chipset.
https://www.vsolcn.com/1ge-sfp-onu-p00193p1.html
 
mgarcia
just joined
Posts: 5
Joined: Fri Apr 05, 2019 12:02 am

Re: Usage GPON module SFP in Spain

Sat Jun 13, 2020 2:53 pm

Dear all.
a few hours ago I ran Zisa with Tilera.
I have heard some comments that were incompatible and I can now confirm that it is certainly compatible.
You can browse my old post regarding the ZISA OP151S. I have made it work by changing only the firmware I mentioned earlier, modifying MAC, SERIAL NUMBER, LoID, and PLOAM PASSWORD / IDONT.

To connect to Zisa ONT:

- create a bridge without STP with ports where laptop connected and Zisa connected

- Add an IP in laptop LAN in 192.168.1.2 (f. Example)

- Connect Zisa ONT to the Fiber from ISP wait untill links UP. if till down after some time reeboot router with all connected.

- Type in webbrowser 192.168.1.1 user: admin pass: admin upgrade firmware mentioned on my last posts from web.

after updated: Make sure your Zisa fiber Link is UP. If not just wait a while or reboot router as mentioned.

- Telnet to 192.168.1.1

user: twmanu - pass: twmanu

- type "?" without wuotes for the menu options.

We just will need manufactory menu to work.

Enter to manufactory menu:

- type: "manufactoy" and press enter

"show ?" without quotes to show all options to check
"set ?" without quotes to show all options to set.

------------------------------------
SERIAL NUMBER:

Inside Manufactory menu:

- type: "show sn" = shows Actual SN
- type: "set sn CCCCXXXXXXXX" with your serial number

confirm change with "show SN" command

------------------------------------

LoID and Password:

inside Manufactory menu:

- type: "show ctc info" (shows actual info) in blank normally


- type: "set ctc loid XXXXXXXXXXXXXXXXXXXXXXXX" (in ASCII Format)
- type: "set ctc password XXXXXXXXXXXXXXXXXXXX" (20digit) without "0x"

If your Loid is in HEX just use one online HEX to ASCII converter.


confirm with "show ctc info" command



after all settings remove from created bridge SFP port and reboot router. ont will connect properly.

I hope all this settings would be fine for all ISP in spain.

After this you should add the corresponding VLAN/ PPPoE if needed from wour ISP in the SFP port to work.

Waiting for Zisa Users who can check this in the forum!

Kind regards!
Last edited by mgarcia on Sun Jun 14, 2020 3:39 am, edited 1 time in total.
 
User avatar
iperezandres
Frequent Visitor
Frequent Visitor
Posts: 51
Joined: Mon Feb 13, 2017 1:17 pm
Location: Madrid
Contact:

Re: Usage GPON module SFP in Spain

Sat Jun 13, 2020 3:12 pm

This is great! Thanks for all the info and detail. My one and only question is: where can I buy a ZISA OP151S module? It seems to be out of stock in all the stores I checked...

Thanks.
 
mgarcia
just joined
Posts: 5
Joined: Fri Apr 05, 2019 12:02 am

Re: Usage GPON module SFP in Spain

Sat Jun 13, 2020 3:38 pm

This is great! Thanks for all the info and detail. My one and only question is: where can I buy a ZISA OP151S module? It seems to be out of stock in all the stores I checked...

Thanks.
I bought in Alibaba.

Kind regards,
 
BackON
just joined
Posts: 7
Joined: Fri Jan 03, 2020 12:58 pm

Re: Usage GPON module SFP in Spain

Sat Jun 27, 2020 1:38 am

hello again


I got several SFP but im not able to connect (zisa op151s g-010s-a g010s-b dfp-34g-2c2) i put the slid on the zisa with the slid and serial but its stuck on 05 state in init.
y tested too the ZTE and the nokia module but im not able to connect. in g-010s-a says error from omci manager


My original ont is a g-010g-p only i have a HEX SLID and serial number
 
Sob
Forum Guru
Forum Guru
Posts: 5899
Joined: Mon Apr 20, 2009 9:11 pm

Re: Usage GPON module SFP in Spain

Wed Jul 15, 2020 4:10 pm

Out of curiosity, what's with the secrecy? You know, the "mail us if you want to know anything", instead of simply making the info public.
People who quote full posts should be spanked with ethernet cable. Some exceptions for multi-topic threads may apply. Not intended as incentive for masochists.
 
Petronas
just joined
Posts: 19
Joined: Mon Aug 26, 2019 7:59 pm

Re: Usage GPON module SFP in Spain

Thu Jul 23, 2020 8:49 pm

Hello. :D

Here is Carlitos' stick. GPON ONU SFP (CPGOS03-0490 v2.0)


Memory processor photos and others Realtek RTL 9601 - Winbond 25Q64JVIQ


Many values can be modified via WebUI and Telnet
You can also change the serial number of the stick by Telnet

Very stable, The only annotation I see is the warm-up, but the same thing happens in other modules
:shock:
I recommend it, get in touch with CarlitoxxPro.
Good quality.

Regards.
You do not have the required permissions to view the files attached to this post.
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Thu Jul 23, 2020 10:07 pm

Hello. :D

Here is Carlitos' stick. GPON ONU SFP (CPGOS03-0490 v2.0)


Memory processor photos and others Realtek RTL 9601 - Winbond 25Q64JVIQ


Many values can be modified via WebUI and Telnet
You can also change the serial number of the stick by Telnet

Very stable, The only annotation I see is the warm-up, but the same thing happens in other modules
:shock:
I recommend it, get in touch with CarlitoxxPro.
Good quality.

Regards.

Great post. Thank you for sharing all these photos with us. We see what is inside the stick :D
It seems CarlitoxxPro has put a lot of work into the module customization and testing to make sure it works with all popular OLT models.
 
JeanPierre
newbie
Posts: 39
Joined: Tue Oct 01, 2019 7:04 pm

Re: Usage GPON module SFP in Spain

Fri Jul 24, 2020 4:59 pm

Memory processor photos and others Realtek RTL 9601
Hi Petronas

Can you share more about Realtek RTL9601C.

What does it display?
cat /proc/cpuinfo

cat /proc/mtd
 
Petronas
just joined
Posts: 19
Joined: Mon Aug 26, 2019 7:59 pm

Re: Usage GPON module SFP in Spain

Sat Jul 25, 2020 1:57 pm

Here, drop this !!!
Memory processor photos and others Realtek RTL 9601
Hi Petronas

Can you share more about Realtek RTL9601C.

What does it display?
cat /proc/cpuinfo

cat /proc/mtd
You do not have the required permissions to view the files attached to this post.
 
vuducdong
just joined
Posts: 2
Joined: Sat Jul 25, 2020 5:46 pm

Re: Usage GPON module SFP in Spain

Mon Jul 27, 2020 5:38 pm

We are very happy :D by announce that we are currently on manufacturing process for the newest version of GPON ONU SFP CPGOS03-0490 V2.

New Architecture, more stability and a great interoperability between multiple OLT brands and Routers/Switches with SFP and SFP+ ports. Fully tested with TriplePlay Services (Data, VoIP, IPTV).

Its Time to replace that unreliable and limited HGU / ONT by a most advanced ONU SFP with a ultra low power compsumption and ready to work on the most faster FTTH networks.

More details very soon!! Please stay tuned. :wink:
Facebook
Twitter
Telegram

Image
I’m sent email to you but not reply ???
Last edited by vuducdong on Mon Aug 31, 2020 11:06 am, edited 3 times in total.
 
JacquesL
just joined
Posts: 8
Joined: Sat Mar 04, 2017 11:24 am

Re: Usage GPON module SFP in Spain

Mon Jul 27, 2020 6:08 pm

Hi guys, Ubiquiti have released a new SFP GPON ONU stick called "UFiber Instant (UF-Instant)".

.....

EDIT: Sorry, I was wrong. Reading instructions for use, this UFiber Instant has no web interface and is configured from a Ubiquiti OLT. It will not work for any Spanish ISP. My fault for not read the instructions for use before...
The system type is RTL8672 , so very similar to the CarlitoxxPro module. Have you tried to understand more? One can telnet to 192.168.1.1 ubnt/ubnt . Apparenly some of the parameters can be set using the flash command. I am wondering if there is a way to get it to work as well
 
JacquesL
just joined
Posts: 8
Joined: Sat Mar 04, 2017 11:24 am

Re: Usage GPON module SFP in Spain

Mon Jul 27, 2020 10:57 pm

Here is Carlitos' stick. GPON ONU SFP (CPGOS03-0490 v2.0)

I recommend it, get in touch with CarlitoxxPro.
Good quality.
Petronas, what user ID and password are you using? I can get the webpage to load on 192.168.1.1 or use telnet but cpAdmin/cpAdmin or cpUser/cpUser is not accepted. I'd like to be able to test the module after waiting so long :)

thank you
 
JacquesL
just joined
Posts: 8
Joined: Sat Mar 04, 2017 11:24 am

Re: Usage GPON module SFP in Spain

Tue Jul 28, 2020 6:13 pm

There have been several reports about new modules with Realtek chips: Ubiquiti UFiber-Instant, V-Solutions - V2801F and many more. I've updated my list of GPON modules.
viewtopic.php?f=3&t=116364&p=771961#p771961

I've been able to make progress with the UFiber-Instant ONU module: it can definitely reach Operation State (o5) on the Movistar (Huwaei) ONT in Spain

Onustate 5.png

However I had to go in the diag system and manually overwrite the PLOAM password, because the flash command limits the GPON_PLOAM_PASSWD to 10 characters in the settings that survive reboots. Still WIP ...
You do not have the required permissions to view the files attached to this post.
 
karman
just joined
Posts: 4
Joined: Thu Jul 30, 2020 8:32 pm

Re: Usage GPON module SFP in Spain

Fri Jul 31, 2020 4:40 am

I received DFP-34X-2C2 and can confirm is working just perfect with pepephone ISP (S/N and Password).

Has anyone had any problem with this module or its twin DFP-34G-2C2 with other spanish ISP?
 
Petronas
just joined
Posts: 19
Joined: Mon Aug 26, 2019 7:59 pm

Re: Usage GPON module SFP in Spain

Fri Aug 07, 2020 4:30 pm

Here is Carlitos' stick. GPON ONU SFP (CPGOS03-0490 v2.0)

I recommend it, get in touch with CarlitoxxPro.
Good quality.
Petronas, what user ID and password are you using? I can get the webpage to load on 192.168.1.1 or use telnet but cpAdmin/cpAdmin or cpUser/cpUser is not accepted. I'd like to be able to test the module after waiting so long :)

thank you
As I said before you can change all the parameters and configurations, via web and telnet.and accept registration in OLT
Get in touch with carlitos, you will find the solution, with the most powerful complete device and support.
Don't waste your time anymore, you have the solution in your hand.
 
User avatar
slarner
newbie
Posts: 31
Joined: Wed Jul 18, 2007 10:54 am
Location: UK
Contact:

Re: Usage GPON module SFP in Spain

Mon Aug 10, 2020 3:17 pm

There have been several reports about new modules with Realtek chips: Ubiquiti UFiber-Instant, V-Solutions - V2801F and many more. I've updated my list of GPON modules.
viewtopic.php?f=3&t=116364&p=771961#p771961

I've been able to make progress with the UFiber-Instant ONU module: it can definitely reach Operation State (o5) on the Movistar (Huwaei) ONT in Spain


Onustate 5.png


However I had to go in the diag system and manually overwrite the PLOAM password, because the flash command limits the GPON_PLOAM_PASSWD to 10 characters in the settings that survive reboots. Still WIP ...
How did you go about accessing the SFP? Ive got it in a Mikrotik atm it just shows the module is present. Does it have an IP you can SSH to it on?
http://www.countybroadband.net
-----------------------------------------------
Provider of wireless broadband in Essex and Suffolk UK
 
vuducdong
just joined
Posts: 2
Joined: Sat Jul 25, 2020 5:46 pm

Re: Usage GPON module SFP in Spain

Tue Aug 11, 2020 12:10 pm

Did you find the temperature of the SFP...?
Last edited by vuducdong on Sun Aug 30, 2020 4:47 am, edited 4 times in total.
 
msatter
Forum Guru
Forum Guru
Posts: 1876
Joined: Tue Feb 18, 2014 12:56 am
Location: Netherlands / Nīderlande

Re: Usage GPON module SFP in Spain

Tue Aug 11, 2020 1:22 pm

Did you find the temperature of the SFP combined with the RB760igs too high when using it? It felt very hot, unable to touch it
viewtopic.php?f=3&t=132258&p=670687&hil ... nk#p671105
One RB4011 (cooled) and a RB760iGS (hEX S) in series. The 4011 Does PPPoE/IKEv2.
The cooler: viewtopic.php?f=3&t=138613&start=300#p799879
Running:
RouterOS 6.48beta35 / Winbox 3.27 64bits / MikroTik APP 1.3.15
 
JacquesL
just joined
Posts: 8
Joined: Sat Mar 04, 2017 11:24 am

Re: Usage GPON module SFP in Spain

Fri Aug 14, 2020 11:42 pm

Don't waste your time anymore, you have the solution in your hand.
You were right Petronas. CarlitoxxPro helped me and the module is working perfectly with Vodafone fiber here in Madrid.

One gotcha, the VPN was not 100 but 24. There are apparently 2 types of connections for Vodafone.
 
JacquesL
just joined
Posts: 8
Joined: Sat Mar 04, 2017 11:24 am

Re: Usage GPON module SFP in Spain

Fri Aug 14, 2020 11:45 pm

How did you go about accessing the SFP? Ive got it in a Mikrotik atm it just shows the module is present. Does it have an IP you can SSH to it on?
The default IP is 192.168.1.1 . You need to add an address like 192.168.1.10/24 to your SFP module

Or you can use an SFP/Ethernet media converter and connect your computer to set it up
 
Vircurus
just joined
Posts: 1
Joined: Fri Nov 15, 2019 5:27 pm

Re: Usage GPON module SFP in Spain

Sun Aug 16, 2020 2:48 pm

Hello. :D

Here is Carlitos' stick. GPON ONU SFP (CPGOS03-0490 v2.0)


Memory processor photos and others Realtek RTL 9601 - Winbond 25Q64JVIQ


Many values can be modified via WebUI and Telnet
You can also change the serial number of the stick by Telnet

Very stable, The only annotation I see is the warm-up, but the same thing happens in other modules
:shock:
I recommend it, get in touch with CarlitoxxPro.
Good quality.

Regards.
hello, you can make a backup of the mtd blocks and put them here
 
User avatar
Gnubyte
just joined
Posts: 12
Joined: Sat Aug 15, 2020 7:31 pm
Location: Toulon - France

Re: Usage GPON module SFP in Spain

Wed Aug 19, 2020 3:25 pm

Hi all,
This thread is tremendous. Really.
I learned a lot of very acurate and exclusive things.

I ordered several kind of GPON SFP, and I will test it asap.
Last edited by Gnubyte on Wed Aug 19, 2020 3:26 pm, edited 1 time in total.
 
User avatar
Gnubyte
just joined
Posts: 12
Joined: Sat Aug 15, 2020 7:31 pm
Location: Toulon - France

Re: Usage GPON module SFP in Spain

Wed Aug 19, 2020 6:16 pm

I Just ordered a CCR2004-1G-12S+2XS
We will soon know if it is exactly adaptable.
 
User avatar
Gnubyte
just joined
Posts: 12
Joined: Sat Aug 15, 2020 7:31 pm
Location: Toulon - France

Re: Usage GPON module SFP in Spain

Thu Aug 20, 2020 3:30 pm

For information, I got a response from CalitoxxPro, apparently more reachable with FB Messenger. I'm waiting some news.
 
User avatar
Gnubyte
just joined
Posts: 12
Joined: Sat Aug 15, 2020 7:31 pm
Location: Toulon - France

Re: Usage GPON module SFP in Spain

Fri Aug 21, 2020 9:45 am

For information, I just paid a CarlitoxxPro GPON SFP ONU, they are available.
 
diablonet
Frequent Visitor
Frequent Visitor
Posts: 59
Joined: Wed Jan 05, 2011 3:33 am

Re: Usage GPON module SFP in Spain

Wed Aug 26, 2020 10:37 am

Hello I own some Zisa modules but after around 15 to 20 days, my mikrotik CCR1016-12S-1S+ (tile) get stuck and the only way to make it work again is by power cycle the mikrotik, have you experienced any issue?
Dear all.
a few hours ago I ran Zisa with Tilera.
I have heard some comments that were incompatible and I can now confirm that it is certainly compatible.
You can browse my old post regarding the ZISA OP151S. I have made it work by changing only the firmware I mentioned earlier, modifying MAC, SERIAL NUMBER, LoID, and PLOAM PASSWORD / IDONT.

To connect to Zisa ONT:

- create a bridge without STP with ports where laptop connected and Zisa connected

- Add an IP in laptop LAN in 192.168.1.2 (f. Example)

- Connect Zisa ONT to the Fiber from ISP wait untill links UP. if till down after some time reeboot router with all connected.

- Type in webbrowser 192.168.1.1 user: admin pass: admin upgrade firmware mentioned on my last posts from web.

after updated: Make sure your Zisa fiber Link is UP. If not just wait a while or reboot router as mentioned.

- Telnet to 192.168.1.1

user: twmanu - pass: twmanu

- type "?" without wuotes for the menu options.

We just will need manufactory menu to work.

Enter to manufactory menu:

- type: "manufactoy" and press enter

"show ?" without quotes to show all options to check
"set ?" without quotes to show all options to set.

------------------------------------
SERIAL NUMBER:

Inside Manufactory menu:

- type: "show sn" = shows Actual SN
- type: "set sn CCCCXXXXXXXX" with your serial number

confirm change with "show SN" command

------------------------------------

LoID and Password:

inside Manufactory menu:

- type: "show ctc info" (shows actual info) in blank normally


- type: "set ctc loid XXXXXXXXXXXXXXXXXXXXXXXX" (in ASCII Format)
- type: "set ctc password XXXXXXXXXXXXXXXXXXXX" (20digit) without "0x"

If your Loid is in HEX just use one online HEX to ASCII converter.


confirm with "show ctc info" command



after all settings remove from created bridge SFP port and reboot router. ont will connect properly.

I hope all this settings would be fine for all ISP in spain.

After this you should add the corresponding VLAN/ PPPoE if needed from wour ISP in the SFP port to work.

Waiting for Zisa Users who can check this in the forum!

Kind regards!
 
JacquesL
just joined
Posts: 8
Joined: Sat Mar 04, 2017 11:24 am

Re: Usage GPON module SFP in Spain

Wed Aug 26, 2020 10:43 am

For information, I just paid a CarlitoxxPro GPON SFP ONU, they are available.
I can confirm that CarlitoxxPro's module works perfectly with Vodafone and Movistar fibre. Getting the 600Mb/s symmetrical speed in both cases.
 
diablonet
Frequent Visitor
Frequent Visitor
Posts: 59
Joined: Wed Jan 05, 2011 3:33 am

Re: Usage GPON module SFP in Spain

Wed Aug 26, 2020 11:07 am

Hello all, according to this info:

=-=-=-=-=-=-=-= Chipset: Intel/Lantiq PEB98035 =-=-=-=-=-=-=-=-=-=-=-=-=
Zisa OP151S
Flash 8MB, RAM 64MB, System T&W Linux atop of OpenWRT 10_03 or 12_09
Pros - Good web interface. A lot of commands.
Cons - It may overheat. Security considerations - some firmware is pre-filled with TR-069 servers.

The firmware interchangeable beetween: T&W TW2362H-CDEL, Zisa OP151S, D-LINK DPN-100, Zyxel PMG3000-D20B, CM5671A, Eltex NTU-SFP-100, Calix 100-03903

I own a Zisa OP151S but after around 15 days it hangs my Mikrotik Tile CCR1016-12S-1S+ fw 6.40.9, I dont know if a fw update on mikrotik or a fw update on zisa may solve the issue, I customize the ont serial and password on the sfp gpon onu, so I need that feature, since the info says I can interchange the firmware with one of the following: T&W TW2362H-CDEL, Zisa OP151S, D-LINK DPN-100, Zyxel PMG3000-D20B, CM5671A, Eltex NTU-SFP-100, Calix 100-03903.

Is any of those replacement firmware support the customizations I require on the gpon serial and password? in order to use it with my mikrotik.
Any suggestion? thank you in advance
 
User avatar
iperezandres
Frequent Visitor
Frequent Visitor
Posts: 51
Joined: Mon Feb 13, 2017 1:17 pm
Location: Madrid
Contact:

Re: Usage GPON module SFP in Spain

Wed Aug 26, 2020 11:41 am

For information, I just paid a CarlitoxxPro GPON SFP ONU, they are available.
I can confirm that CarlitoxxPro's module works perfectly with Vodafone and Movistar fibre. Getting the 600Mb/s symmetrical speed in both cases.
Hello,
I have O2 (movistar in the end) and I am having troubles making it work. I have an Alcatel ONT I240G-T, I have extracted its serial number from its label (ALCL...) and the PLOAM using telnet (F2018....).
I have followd CarlitoxxPro manual, but the PPPoE session does not connect.
I have the SFP interface on, the VLAN6 under that interface, and the PPPoE session over the VLAN6.
Any clue of what I might be doing wrong?
Thanks.
 
diablonet
Frequent Visitor
Frequent Visitor
Posts: 59
Joined: Wed Jan 05, 2011 3:33 am

Re: Usage GPON module SFP in Spain

Fri Aug 28, 2020 12:15 am

For information, I just paid a CarlitoxxPro GPON SFP ONU, they are available.
I can confirm that CarlitoxxPro's module works perfectly with Vodafone and Movistar fibre. Getting the 600Mb/s symmetrical speed in both cases.
Hello JacquesL, in my country I have availability for the Ubiquiti U-Fiber Instant for 48 USD, much cheaper than the Carlitoxx, can you please share how did you managed to change some parameters via CLI? my ips just requieres SERIAL NUMBER (ALCLXXXXXXXX) and PASSWORD (less than 10 characters in ASCII MODE), maybe it runs for my purpose, thank you
 
User avatar
iperezandres
Frequent Visitor
Frequent Visitor
Posts: 51
Joined: Mon Feb 13, 2017 1:17 pm
Location: Madrid
Contact:

Re: Usage GPON module SFP in Spain

Fri Aug 28, 2020 9:59 am

For information, I just paid a CarlitoxxPro GPON SFP ONU, they are available.
I can confirm that CarlitoxxPro's module works perfectly with Vodafone and Movistar fibre. Getting the 600Mb/s symmetrical speed in both cases.
What ONT did you have before the change? I have an Alcatel i240g-t and I have been told that my provider (O2) needs to unblock the administrative state at the OTL so I can work with Carlitoxx SFP module. I have already made the request, but I don't really count on the provider doing it... Is there any other alternative?
 
pajal2006
just joined
Posts: 2
Joined: Mon Aug 31, 2020 1:52 am

Re: Usage GPON module SFP in Spain

Mon Aug 31, 2020 2:03 am

Iperezandres

Hi, I'm in the same situation as your iperezandres if you get something tell me. Thank you.
 
User avatar
iperezandres
Frequent Visitor
Frequent Visitor
Posts: 51
Joined: Mon Feb 13, 2017 1:17 pm
Location: Madrid
Contact:

Re: Usage GPON module SFP in Spain

Mon Aug 31, 2020 4:34 pm

I am waiting for O2 to reply to my request about the administrative state, but not luck so far...
 
User avatar
Gnubyte
just joined
Posts: 12
Joined: Sat Aug 15, 2020 7:31 pm
Location: Toulon - France

Re: Usage GPON module SFP in Spain

Tue Sep 01, 2020 12:17 pm

Some news -
CarlitoxxPro ONU authentifies Orange FFTH to O5 with PLOAM and huawei profile BUT it is not recognized completely by the CCR2004, and it do not synchronize 2,5Gbps SFP side.
I follow my tests
 
User avatar
CarlitoxxPro
just joined
Posts: 23
Joined: Wed Jan 04, 2017 10:15 am
Location: Spain
Contact:

Re: Usage GPON module SFP in Spain

Thu Sep 03, 2020 4:11 pm

Some news -
CarlitoxxPro ONU authentifies Orange FFTH to O5 with PLOAM and huawei profile BUT it is not recognized completely by the CCR2004, and it do not synchronize 2,5Gbps SFP side.
I follow my tests
Hi Gnubyte, as may you already know, that SFP only has 1GE, so links for more than 1Gbps is not supported by the interface. apart of that think that you are using an SFP into an SFP+ port the auto-negotiation can fail by an issue in the router software (ROS), you can find many issues related with that on the forum and on the internet,

if you check the Mikrotik SFP support table, there is mentioned this: https://wiki.mikrotik.com/wiki/MikroTik ... lity_table
did you tried to set manual link speed to 1Gbps full-duplex to the SFP+ port?

out of that, take in mind to than all devices of the link need to support and be configured to negotiate the full-duplex at 2.5G to the link be established successfully.

Related to the "is not recognized completely by the CCR2004", what is the issue that you observed?
can be related to this? viewtopic.php?f=3&t=165386
Facebook: fb.me.com/CarlitoxxPro
Twitter: @CarlitoxxPro
Telegram: t.me/CarlitoxxPro
Email: contacto [at] carlitoxxpro.com
 
xoy74
just joined
Posts: 1
Joined: Mon Sep 07, 2020 9:03 pm

Re: Usage GPON module SFP in Spain

Tue Sep 08, 2020 2:27 am

Thanks for your work on different GPON SFP modules.
I have a couple of MA5671A from Bell Canada. I can SSH into them at 192.168.1.10 but haven't been able to find any useful commands that could be used inside the SSH session. Are they documented anywhere that you know of ?
Last edited by xoy74 on Tue Sep 08, 2020 4:14 am, edited 1 time in total.
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Tue Sep 15, 2020 9:58 am

Hello guys,

I have tested so far:

ZISA OP151S
DFP-34G-2C2
DIPPER OPTICS D23446-SSHE
HUAWEI HG8010H (not SFP. Pure bridge device with one ETH port)

All of the tested resulted the same!
With all of these modules and HUAWEI device I can get O5 state for GPON and I can access the native VLAN on the ethernet which is dedicated for IPTV but no tagged traffic is coming out on the other side of the stick or LAN port of HG8010H. I tried to make a WAN interface on DFP-34G-2C2 with the same VLAN IDs and it could access it but making a pure bridge was never successful. This made me believe that there is some QinQ with the default VLAN ID so it works as a WAN interface on DFP-34G-2C2 or HUAWEI HG8245H but does not work if I try to access VLANs via mikrotik or any other managed network device. Other users experienced the same.

OR... Alll the above mentioned modules does not work in transparent mode.

Therefore, I believe, not even CarlitoxxPro latest stick will work if I don't find out what is the problem with these.

Can anyone help me out with this? I believe this may help others too.

Best Regards.
 
User avatar
Gnubyte
just joined
Posts: 12
Joined: Sat Aug 15, 2020 7:31 pm
Location: Toulon - France

Re: Usage GPON module SFP in Spain

Tue Sep 15, 2020 3:38 pm

Some news -
CarlitoxxPro ONU authentifies Orange FFTH to O5 with PLOAM and huawei profile BUT it is not recognized completely by the CCR2004, and it do not synchronize 2,5Gbps SFP side.
I follow my tests
Hi Gnubyte, as may you already know, that SFP only has 1GE, so links for more than 1Gbps is not supported by the interface. apart of that think that you are using an SFP into an SFP+ port the auto-negotiation can fail by an issue in the router software (ROS), you can find many issues related with that on the forum and on the internet,
When I set it non autonegociated 1Gbps Full Duplex, It runs in (R) state. But, Orange don't give the IP. I'm going to force the serial.
if you check the Mikrotik SFP support table, there is mentioned this: https://wiki.mikrotik.com/wiki/MikroTik ... lity_table
did you tried to set manual link speed to 1Gbps full-duplex to the SFP+ port?
Even 1Gb FDX.
out of that, take in mind to than all devices of the link need to support and be configured to negotiate the full-duplex at 2.5G to the link be established successfully.

Related to the "is not recognized completely by the CCR2004", what is the issue that you observed?
can be related to this? viewtopic.php?f=3&t=165386
It can be related, so I added my vote.
 
pajal2006
just joined
Posts: 2
Joined: Mon Aug 31, 2020 1:52 am

Re: Usage GPON module SFP in Spain

Wed Sep 16, 2020 12:23 pm

I am waiting for O2 to reply to my request about the administrative state, but not luck so far...
Good, have you answered something in O2 ??? ... Movistar does not want to do it to me. I have the CarlitoxxxPro SFP of paperweight.
 
User avatar
iperezandres
Frequent Visitor
Frequent Visitor
Posts: 51
Joined: Mon Feb 13, 2017 1:17 pm
Location: Madrid
Contact:

Re: Usage GPON module SFP in Spain

Wed Sep 16, 2020 12:34 pm

I am waiting for O2 to reply to my request about the administrative state, but not luck so far...
Good, have you answered something in O2 ??? ... Movistar does not want to do it to me. I have the CarlitoxxxPro SFP of paperweight.
Pretty much the same here. I have talked quite some times to O2 but still they cannot figure out who should I be talking to. It is being escalated internally, but does not look good...

I am also talking to CarlitoXXPro because my GPON is always in O5 state, regardless of the PLOAM that I configure. I have confirmed with the O2 technician that the PLOAM I have is the correct one, but if I set a fake one, the GPON shows O5 anyway, so I am also wondering if the GPON is defective. No luck so far.
 
karman
just joined
Posts: 4
Joined: Thu Jul 30, 2020 8:32 pm

Re: Usage GPON module SFP in Spain

Thu Sep 17, 2020 4:42 pm

Hello guys,

I have tested so far:

ZISA OP151S
DFP-34G-2C2
DIPPER OPTICS D23446-SSHE
HUAWEI HG8010H (not SFP. Pure bridge device with one ETH port)

All of the tested resulted the same!
With all of these modules and HUAWEI device I can get O5 state for GPON and I can access the native VLAN on the ethernet which is dedicated for IPTV but no tagged traffic is coming out on the other side of the stick or LAN port of HG8010H. I tried to make a WAN interface on DFP-34G-2C2 with the same VLAN IDs and it could access it but making a pure bridge was never successful. This made me believe that there is some QinQ with the default VLAN ID so it works as a WAN interface on DFP-34G-2C2 or HUAWEI HG8245H but does not work if I try to access VLANs via mikrotik or any other managed network device. Other users experienced the same.

OR... Alll the above mentioned modules does not work in transparent mode.

Therefore, I believe, not even CarlitoxxPro latest stick will work if I don't find out what is the problem with these.

Can anyone help me out with this? I believe this may help others too.

Best Regards.
Maybe I can help. I have the DFP-34X-2C2 (which is the same as DFP-34G-2C2 but supports both EPON and GPON). You should NOT create WAN connection. If you do it the SFP will act as a router. You should leave it without WAN connection to get bridge access and pass all VLANs to the attached device.

In my case my ISP provider offers internet in VLAN20, so I have to make sure that the SFP port accepts traffic from VLAN20 (virtual interface vlan 20?).
 
ranpha
Frequent Visitor
Frequent Visitor
Posts: 55
Joined: Mon Jan 09, 2012 3:16 am

Re: Usage GPON module SFP in Spain

Thu Sep 17, 2020 5:28 pm

Hello guys,

I have tested so far:

ZISA OP151S
DFP-34G-2C2
DIPPER OPTICS D23446-SSHE
HUAWEI HG8010H (not SFP. Pure bridge device with one ETH port)

All of the tested resulted the same!
With all of these modules and HUAWEI device I can get O5 state for GPON and I can access the native VLAN on the ethernet which is dedicated for IPTV but no tagged traffic is coming out on the other side of the stick or LAN port of HG8010H. I tried to make a WAN interface on DFP-34G-2C2 with the same VLAN IDs and it could access it but making a pure bridge was never successful. This made me believe that there is some QinQ with the default VLAN ID so it works as a WAN interface on DFP-34G-2C2 or HUAWEI HG8245H but does not work if I try to access VLANs via mikrotik or any other managed network device. Other users experienced the same.

OR... Alll the above mentioned modules does not work in transparent mode.

Therefore, I believe, not even CarlitoxxPro latest stick will work if I don't find out what is the problem with these.

Can anyone help me out with this? I believe this may help others too.

Best Regards.
Maybe I can help. I have the DFP-34X-2C2 (which is the same as DFP-34G-2C2 but supports both EPON and GPON). You should NOT create WAN connection. If you do it the SFP will act as a router. You should leave it without WAN connection to get bridge access and pass all VLANs to the attached device.

In my case my ISP provider offers internet in VLAN20, so I have to make sure that the SFP port accepts traffic from VLAN20 (virtual interface vlan 20?).
Do you have to put VLAN information in 'Application ---> Multicast ---> VLAN Configuration' section? I have the exact same GPON stick but cannot connect to the Internet via PPPoE at all.
 
karman
just joined
Posts: 4
Joined: Thu Jul 30, 2020 8:32 pm

Re: Usage GPON module SFP in Spain

Thu Sep 17, 2020 6:24 pm

Hello guys,

I have tested so far:

ZISA OP151S
DFP-34G-2C2
DIPPER OPTICS D23446-SSHE
HUAWEI HG8010H (not SFP. Pure bridge device with one ETH port)

All of the tested resulted the same!
With all of these modules and HUAWEI device I can get O5 state for GPON and I can access the native VLAN on the ethernet which is dedicated for IPTV but no tagged traffic is coming out on the other side of the stick or LAN port of HG8010H. I tried to make a WAN interface on DFP-34G-2C2 with the same VLAN IDs and it could access it but making a pure bridge was never successful. This made me believe that there is some QinQ with the default VLAN ID so it works as a WAN interface on DFP-34G-2C2 or HUAWEI HG8245H but does not work if I try to access VLANs via mikrotik or any other managed network device. Other users experienced the same.

OR... Alll the above mentioned modules does not work in transparent mode.

Therefore, I believe, not even CarlitoxxPro latest stick will work if I don't find out what is the problem with these.

Can anyone help me out with this? I believe this may help others too.

Best Regards.
Maybe I can help. I have the DFP-34X-2C2 (which is the same as DFP-34G-2C2 but supports both EPON and GPON). You should NOT create WAN connection. If you do it the SFP will act as a router. You should leave it without WAN connection to get bridge access and pass all VLANs to the attached device.

In my case my ISP provider offers internet in VLAN20, so I have to make sure that the SFP port accepts traffic from VLAN20 (virtual interface vlan 20?).
Do you have to put VLAN information in 'Application ---> Multicast ---> VLAN Configuration' section? I have the exact same GPON stick but cannot connect to the Internet via PPPoE at all.
Nope, works plainly. PPPoE is not a matter of the ONU but the router on it's proper virtual vlan interface.
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Thu Sep 17, 2020 9:38 pm



Maybe I can help. I have the DFP-34X-2C2 (which is the same as DFP-34G-2C2 but supports both EPON and GPON). You should NOT create WAN connection. If you do it the SFP will act as a router. You should leave it without WAN connection to get bridge access and pass all VLANs to the attached device.

In my case my ISP provider offers internet in VLAN20, so I have to make sure that the SFP port accepts traffic from VLAN20 (virtual interface vlan 20?).
Hi, Many thanks for reply! I did everything like it should be. I have no WAN connections on the stick itself. However, if I try to add WAN connections then I am able to open all VLANs on the stick itself but when all WANs are removed, I am not able (mikrotik doesn't detect any VLAN tags) to access VLANs. It seems like it doesn't work as a bridge. Native (untagged traffic dedicated for IPTV) VLAN is available but no tagged traffic. If You know what to do, I will give You access to my PC and will pay You for a successful setup.

Best Regards.
 
ranpha
Frequent Visitor
Frequent Visitor
Posts: 55
Joined: Mon Jan 09, 2012 3:16 am

Re: Usage GPON module SFP in Spain

Fri Sep 18, 2020 7:08 am

Do you have to put VLAN information in 'Application ---> Multicast ---> VLAN Configuration' section? I have the exact same GPON stick but cannot connect to the Internet via PPPoE at all.
Nope, works plainly. PPPoE is not a matter of the ONU but the router on it's proper virtual vlan interface.
Ok, so all I have to do is to put the OLT password in the SFP, and then put a VLAN interface on the SFP socket in routerOS, then run a PPPoE dialer on that VLAN interface?
IGMP snooping has to be enabled on the GPON stick?
 
valemal
just joined
Posts: 2
Joined: Wed Jul 08, 2020 12:56 am

Re: Usage GPON module SFP in Spain

Fri Sep 18, 2020 12:37 pm

Hey. You can help me? I configured my PON STICK ONU SFP module via telnet and killed the firmware. Can you give me the firmware?Image
Last edited by valemal on Fri Sep 18, 2020 2:59 pm, edited 2 times in total.
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Fri Sep 18, 2020 2:41 pm

I am willing to pay for a successful setup for at least one of these devices:

DFP-34G-2C2
DIPPER OPTICS D23446-SSHE
HUAWEI HG8010H (not SFP. Pure bridge device with one ETH port)

I need VLANs available in mikrotik. I know VLAN IDs, except DPOptics, other two can successfully register to OLT. With DPOptics I never achieved a successful registration to OLT.

All I get now is one untagged VLAN which is IPTV.

Is there anyone interested and willing to help?
 
Florian
Frequent Visitor
Frequent Visitor
Posts: 85
Joined: Sun Mar 13, 2016 9:45 am
Location: France

Re: Usage GPON module SFP in Spain

Sat Sep 19, 2020 7:54 pm

So it's limited at 1g ? In France (and i guess others countries too) Orange, SFR, Bouygues, offer more than 1gb now, still on gpon tech.
- Sorry for my english -
 
wiper
just joined
Posts: 1
Joined: Wed Aug 26, 2020 2:31 pm

Re: Usage GPON module SFP in Spain

Sun Sep 20, 2020 4:18 am

Hi, I bought the module "CarlitoxxPro GPON ONU SFP (CPGOS03-0490 v2.0)", I want to share some of my conclusions after doing many tests.

- It is not 100% compatible with all Mikrotik routers, as comrade Gnubyte commented, the module is not always detected by the router, you have to remove and reconnect the module several times until it works.
- The SFP module does not have a link until the fiber cable is connected, therefore it is not possible to configure it or check the status if the optical fiber fails, for example due to a damaged cable.
- The module status screen always indicates O5, it never changes.
- Needs to takes a long time to sync and connect with the OLT.
- Sometimes the module crashes, link is UP but not responding.
- It is not possible to do Port Forwarding, nor have I been able to receive RIP routing, I would say that the bridge does not work well.

It is not an easy task, but once connected and synchronized with the OLT, all the VLANs work and the transfer speed is correct.

In my opinion it does not work 100% well, I would not install it in a production environment, at the moment it is only valid for tests or as a paperweight.

If anyone is interested in buying this module, mine is for sale, contact me, we can surely reach an agreement.

Greetings.
Last edited by wiper on Sun Sep 20, 2020 4:21 am, edited 1 time in total.
 
spaxton
Member Candidate
Member Candidate
Posts: 181
Joined: Fri Jan 01, 2010 12:18 pm

Re: Usage GPON module SFP in Spain

Mon Sep 21, 2020 9:54 am

Hi, I bought the module "CarlitoxxPro GPON ONU SFP (CPGOS03-0490 v2.0)", I want to share some of my conclusions after doing many tests.

- It is not 100% compatible with all Mikrotik routers, as comrade Gnubyte commented, the module is not always detected by the router, you have to remove and reconnect the module several times until it works.
- The SFP module does not have a link until the fiber cable is connected, therefore it is not possible to configure it or check the status if the optical fiber fails, for example due to a damaged cable.
- The module status screen always indicates O5, it never changes.
- Needs to takes a long time to sync and connect with the OLT.
- Sometimes the module crashes, link is UP but not responding.
- It is not possible to do Port Forwarding, nor have I been able to receive RIP routing, I would say that the bridge does not work well.

It is not an easy task, but once connected and synchronized with the OLT, all the VLANs work and the transfer speed is correct.

In my opinion it does not work 100% well, I would not install it in a production environment, at the moment it is only valid for tests or as a paperweight.

If anyone is interested in buying this module, mine is for sale, contact me, we can surely reach an agreement.

Greetings.
You reported a lot of bugs for it. However, port forwarding should not be done on the module itself. This module should work as a pure bridge. For me will be enough if it works stable inside of the media converter cage. Send me Your offer in pm including shipping costs to Montenegro and a payment method.

By the way... Have You ever had a module which worked for You? Which one was it and how did You configure it? I offered to pay to the one who can make a working configuration with certain modules mentioned in this thread but nobody answered. It seems that nobody ever made it work or nobody wants money.

Best Regards.
 
karman
just joined
Posts: 4
Joined: Thu Jul 30, 2020 8:32 pm

Re: Usage GPON module SFP in Spain

Tue Sep 22, 2020 2:49 pm

I am willing to pay for a successful setup for at least one of these devices:

DFP-34G-2C2
DIPPER OPTICS D23446-SSHE
HUAWEI HG8010H (not SFP. Pure bridge device with one ETH port)

I need VLANs available in mikrotik. I know VLAN IDs, except DPOptics, other two can successfully register to OLT. With DPOptics I never achieved a successful registration to OLT.

All I get now is one untagged VLAN which is IPTV.

Is there anyone interested and willing to help?
Actually as the ONU SFP acts as bridge you should think of it as a TRUNK. All VLANs passthrough it to the 'next stage', in this case the router, so you should have one virtual interface per vlan.

I'm sorry but I'm no mikrotik expert, I'm unable to help yuo with the exact needed steps.
 
sotirone
just joined
Posts: 4
Joined: Tue Oct 22, 2019 2:07 am

Re: Usage GPON module SFP in Spain

Thu Sep 24, 2020 10:00 pm

Hi, I bought the module "CarlitoxxPro GPON ONU SFP (CPGOS03-0490 v2.0)", I want to share some of my conclusions after doing many tests.

- It is not 100% compatible with all Mikrotik routers, as comrade Gnubyte commented, the module is not always detected by the router, you have to remove and reconnect the module several times until it works.
- The SFP module does not have a link until the fiber cable is connected, therefore it is not possible to configure it or check the status if the optical fiber fails, for example due to a damaged cable.
- The module status screen always indicates O5, it never changes.
- Needs to takes a long time to sync and connect with the OLT.
- Sometimes the module crashes, link is UP but not responding.
- It is not possible to do Port Forwarding, nor have I been able to receive RIP routing, I would say that the bridge does not work well.

It is not an easy task, but once connected and synchronized with the OLT, all the VLANs work and the transfer speed is correct.

In my opinion it does not work 100% well, I would not install it in a production environment, at the moment it is only valid for tests or as a paperweight.

If anyone is interested in buying this module, mine is for sale, contact me, we can surely reach an agreement.

Greetings.
I would like to buy the SFP. Please send me a PM. Thanks!
 
sotirone
just joined
Posts: 4
Joined: Tue Oct 22, 2019 2:07 am

Re: Usage GPON module SFP in Spain

Fri Sep 25, 2020 8:29 pm

Has anyone tried CarlitoxxPro's SFP with pfSense?

Is the OS important or not? Is there a driver that needs to be loaded?

Does it work with Mellanox 10Gb SFP+ adapters? (specifically the Mellanox ConnectX-3).

Who is online

Users browsing this forum: No registered users and 25 guests