Community discussions

MikroTik App
 
nkourtzis
Member Candidate
Member Candidate
Topic Author
Posts: 214
Joined: Tue Dec 11, 2012 12:56 am
Location: Greece

mAP Lite Ethernet susceptible to interference!

Fri Feb 05, 2016 12:43 am

Today I had the following experience with my new mAP lite: I used the integrated magnet to stick it onto a metallic TP-Link 8-port gigabit soho switch. It took me about an hour to debug what I was seeing, but at last I figured that when the surfaces of the two devices were in contact, the ethernet port would connect at 10Mbps full duplex after a long negotiation process and no data would pass through! As soon as the mAP was detached from the switch, everything worked just fine. The exact place on the surface of the switch on which the mAP attached did not seem to make any significant difference.

Obviously there was some kind of interference that impaired the ethernet controller.

I suppose minuscule size comes at a price, but could there be a second revision with some kind of shielding around the board?

PS: The offending switch: http://www.tp-link.com/lk/products/deta ... SG108.html
 
User avatar
ZeroByte
Forum Guru
Forum Guru
Posts: 4047
Joined: Wed May 11, 2011 6:08 pm

Re: mAP Lite Ethernet susceptible to interference!

Fri Feb 05, 2016 12:50 am

have you tried putting some insulator between the map lite and the switch? It could be some kind of grounding issue that's leading to it.
Then I would try touching the MAP lite to the switch, but backwards so the magnet wasn't sticking.

Basically - if it interferes just based on proximity (with insulator, but sticking with magnet, or touching but backwards so no magnet) then try it in proximity to other ethernet devices, monitors, tv sets, electric appliances, etc.

Since I'm assuming it's plugged into the same switch that you're sticking it to with the magnet, I wonder if a grounding loop is interfering with the signal propagation along the cat5. Have you tried other cables?
 
nkourtzis
Member Candidate
Member Candidate
Topic Author
Posts: 214
Joined: Tue Dec 11, 2012 12:56 am
Location: Greece

Re: mAP Lite Ethernet susceptible to interference!

Fri Feb 05, 2016 1:01 am

Unfortunately I cannot do further tests right now, since it is a production environment (and my only mAPL so far). But I will put them in my to-do list. Thing is, the outside of the mAPL is plastic, except from the ethernet post shield which is exposed and was almost certainly touching the switch case. The cable was not shielded though, just an ordinary cat5e patch with plastic plugs. I should probably try to put just a sheet of paper/plastic between them.
 
User avatar
kiler129
Member
Member
Posts: 352
Joined: Tue Mar 31, 2015 4:32 pm
Location: IL, USA
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Fri Feb 05, 2016 3:32 am

Some ethernet poor quality RJ45 sockets MAY be affected by magnets and EMI. Since it's TP-Link I'm not really surprised ;)
 
bazzer
Trainer
Trainer
Posts: 87
Joined: Sat Mar 07, 2009 11:51 pm
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Sun Feb 07, 2016 6:12 pm

I too have discovered issues with the magnets within the mAP lite. I find if the device is stuck in place with the magnet or the small backing plate that comes with it is placed on the back, the ethernet port will fail and sync to 10mbit with no data passed through it. If you boot the lite without it attached to a metal surface, the etherport works fine
 
User avatar
Cha0s
Forum Guru
Forum Guru
Posts: 1135
Joined: Tue Oct 11, 2005 4:53 pm

Re: mAP Lite Ethernet susceptible to interference!

Wed Mar 02, 2016 8:05 pm

I confirm the issue.

I have 3 mAP Lite and all 3 exhibit the same behavior as mentioned.

The surface does not seem to matter.

I've 'stuck' it over a switch, on a server, on a UPS, on the rack itself and the result is the same. No data passes through the ethernet.
The moment I remove it from any metallic surface the ethernet works like a charm.

I wonder if we can request a refund from the distributors since this is obviously a design flaw and the device does not work as advertised (at least in my country you are entitled by law for a replacement or full refund in case the product does not work as advertised).

I'll contact my distributor about returning these.

To add to the design flaw, when data passes through wifi, it will make a high pitch sound which is rather annoying when using the device in a silent room.
http://forum.mikrotik.com/viewtopic.php ... 04#p519204
 
User avatar
ZeroByte
Forum Guru
Forum Guru
Posts: 4047
Joined: Wed May 11, 2011 6:08 pm

Re: mAP Lite Ethernet susceptible to interference!

Wed Mar 02, 2016 8:24 pm

Does this happen if there's an insulator between the magnet and the surface it's stuck to?
(like if you had a strip of electrical tape on the metal, and stuck the magnet to that tape only)
 
User avatar
doneware
Trainer
Trainer
Posts: 647
Joined: Mon Oct 08, 2012 8:39 pm
Location: Hungary

Re: mAP Lite Ethernet susceptible to interference!

Wed Mar 02, 2016 8:53 pm

try to put it onto a non-metallic surface.

tmbk they tested it thoroughly, but the magnetic field generated by the magnets that hold the device onto something is influenced and deformed by the attached metallic surface itself. this causes interference in the wireless part for sure, and i guess this interference can also influence the ethernet side transformers too.
 
darkprocess
Member Candidate
Member Candidate
Posts: 249
Joined: Fri Mar 20, 2015 1:16 pm

mAP Lite Ethernet susceptible to interference!

Wed Mar 02, 2016 10:37 pm

Same issue here. Bad design ? What can be the solution, remove the magnets?
 
User avatar
chechito
Forum Guru
Forum Guru
Posts: 2989
Joined: Sun Aug 24, 2014 3:14 am
Location: Bogota Colombia
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Wed Mar 02, 2016 10:40 pm

i think ehernet is vulnerable to interference by itself, you have to guarantee good cabling and avoid any source of interference to be safe

of course i think a strong magnet so close to a electronic device is a bad idea
 
Sob
Forum Guru
Forum Guru
Posts: 9119
Joined: Mon Apr 20, 2009 9:11 pm

Re: mAP Lite Ethernet susceptible to interference!

Wed Mar 02, 2016 10:44 pm

Does this happen if there's an insulator between the magnet and the surface it's stuck to?
Magnets are inside, so no matter what you stick it on, there's always mAP's plastic body between magnets and surface. Not even ethernet connector can touch it, because it's covered from back side.
 
User avatar
doneware
Trainer
Trainer
Posts: 647
Joined: Mon Oct 08, 2012 8:39 pm
Location: Hungary

Re: mAP Lite Ethernet susceptible to interference!

Thu Mar 03, 2016 12:20 am

Same issue here. Bad design ? What can be the solution, remove the magnets?
must be ok as long you do NOT attach it to anything metallic (ferromagnetic)
 
darkprocess
Member Candidate
Member Candidate
Posts: 249
Joined: Fri Mar 20, 2015 1:16 pm

mAP Lite Ethernet susceptible to interference!

Sun Mar 06, 2016 2:34 pm

Can someone from mikrotik provide an answer to this issue
 
ALDISBEHMANIS
just joined
Posts: 16
Joined: Mon Aug 18, 2008 3:32 pm

Re: mAP Lite Ethernet susceptible to interference!

Tue Mar 15, 2016 2:21 pm

Same problem here.
Even tried changing unit.
Design flaw!
 
darkprocess
Member Candidate
Member Candidate
Posts: 249
Joined: Fri Mar 20, 2015 1:16 pm

mAP Lite Ethernet susceptible to interference!

Tue Mar 15, 2016 7:48 pm

Mikrotik could you please provide an answer. Maplite is a great product anyway
 
bazzer
Trainer
Trainer
Posts: 87
Joined: Sat Mar 07, 2009 11:51 pm
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Tue Mar 15, 2016 10:56 pm

Remove internal magnets and stick flexi sticky backed magnet to outside of mAP lite (also works for fat mAP)
Image
Image
 
3bs
Frequent Visitor
Frequent Visitor
Posts: 55
Joined: Tue Aug 09, 2011 12:33 am
Location: Irkutsk, Russia

Re: mAP Lite Ethernet susceptible to interference!

Thu Mar 17, 2016 11:17 am

And again, no comments from mikrotik :)
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26287
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: mAP Lite Ethernet susceptible to interference!

Thu Mar 17, 2016 11:27 am

If you find any hardware related issue with our products, please contact the seller to arrange a replacement via Warranty repair services.
 
3bs
Frequent Visitor
Frequent Visitor
Posts: 55
Joined: Tue Aug 09, 2011 12:33 am
Location: Irkutsk, Russia

Re: mAP Lite Ethernet susceptible to interference!

Sun Mar 20, 2016 4:56 am

If you find any hardware related issue with our products, please contact the seller to arrange a replacement via Warranty repair services.
Noise when wifi work - hardware issue, or feature (all work fine except small noise)?
And ethernet that stop work after attach to mettal surface.
Maybe it's all hardware features? :)
 
Sob
Forum Guru
Forum Guru
Posts: 9119
Joined: Mon Apr 20, 2009 9:11 pm

Re: mAP Lite Ethernet susceptible to interference!

Sun Mar 20, 2016 6:04 am

Noise when wifi work - hardware issue, or feature (all work fine except small noise)?
It's MWAAF, MikroTik Wireless Activity Audio Feedback™. Patent pending. And for no extra charge!
 
DmitryAVET
Member Candidate
Member Candidate
Posts: 112
Joined: Thu Mar 26, 2015 12:27 am
Location: Ukraine, Mukachevo
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Sun Mar 20, 2016 8:54 pm

If you find any hardware related issue with our products, please contact the seller to arrange a replacement via Warranty repair services.
Noise when wifi work - hardware issue, or feature (all work fine except small noise)?
And ethernet that stop work after attach to mettal surface.
Maybe it's all hardware features? :)
+1
Confirm noise on high load

Maybe power system?
mikrotik_rbmapl_2nd_map_lite_review_11_hardware.JPG
You do not have the required permissions to view the files attached to this post.
 
User avatar
kiler129
Member
Member
Posts: 352
Joined: Tue Mar 31, 2015 4:32 pm
Location: IL, USA
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Sun Mar 20, 2016 10:20 pm

It could be piezeoelectric effect of capacitors.

Details: https://www.youtube.com/watch?v=F2gX-R1k7MM
 
fragtion
Member Candidate
Member Candidate
Posts: 257
Joined: Fri Nov 13, 2009 10:08 pm
Location: Johannesburg, South Africa

Re: mAP Lite Ethernet susceptible to interference!

Mon Apr 18, 2016 7:45 pm

I've got the same problem with my mAP Lite. I noticed a problem with ethernet connectivity immediately after unboxing on first use, but didn't realize that it was caused by a design flaw with the magnet until reading this thread

Update: Mine's working perfectly since removing the magnets.
 
User avatar
juanvi
Member Candidate
Member Candidate
Posts: 165
Joined: Mon May 05, 2014 6:55 pm
Location: SPAIN

Re: mAP Lite Ethernet susceptible to interference!

Wed May 11, 2016 11:56 am

Broken Eth in one of my 3 map lite. Interface shows intermitent disconnections of few seconds. Faulty device? Magnets?Anyone else? Some news from MT side? I love this device, please MT give him some love too. :D
 
SolarW
newbie
Posts: 40
Joined: Mon Nov 29, 2010 3:37 am

Re: mAP Lite Ethernet susceptible to interference!

Wed May 11, 2016 4:48 pm

Can confirm this issue - my 3 mAP Light have this problem.

1. Install to magnetic surface
2. Reboot or power cycle
3. Ethernet port not work

Temporarily solution (tnx to this post writers)

Solution 1 (without warranty void)
- install on NOT magnetic surface (on double-sided adhesive tape for example)

Solution 2 (with warranty lost)
- remove magnets from mAP Light cover
 
SolarW
newbie
Posts: 40
Joined: Mon Nov 29, 2010 3:37 am

Re: mAP Lite Ethernet susceptible to interference!

Wed May 11, 2016 4:49 pm

If you find any hardware related issue with our products, please contact the seller to arrange a replacement via Warranty repair services.
Realy?
You have solution for this problem?
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26287
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: mAP Lite Ethernet susceptible to interference!

Wed May 11, 2016 4:59 pm

Well yes, we are able to fix most problems, I wrote about this in March already, so you would have received the repaired unit by now. Our RMA department needs to see your unit before we can make a definite conclusion what exactly was wrong.
 
SolarW
newbie
Posts: 40
Joined: Mon Nov 29, 2010 3:37 am

Re: mAP Lite Ethernet susceptible to interference!

Wed May 11, 2016 5:07 pm

Well yes, we are able to fix most problems, I wrote about this in March already, so you would have received the repaired unit by now. Our RMA department needs to see your unit before we can make a definite conclusion what exactly was wrong.
Sounds like good :)
I'm buy my mAP Light only two week ago - in March you write not for me :)
 
littlebill
Member Candidate
Member Candidate
Posts: 234
Joined: Sat Apr 30, 2011 3:11 am

Re: mAP Lite Ethernet susceptible to interference!

Tue May 24, 2016 6:29 am

Well yes, we are able to fix most problems, I wrote about this in March already, so you would have received the repaired unit by now. Our RMA department needs to see your unit before we can make a definite conclusion what exactly was wrong.

so what is the link to the fix? apparently everyone has this problem
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26287
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: mAP Lite Ethernet susceptible to interference!

Tue May 24, 2016 8:24 am

Well yes, we are able to fix most problems, I wrote about this in March already, so you would have received the repaired unit by now. Our RMA department needs to see your unit before we can make a definite conclusion what exactly was wrong.

so what is the link to the fix? apparently everyone has this problem
Like I said, with any device that has any kind of problem, submit it to RMA for repair, so we can fix it.
 
littlebill
Member Candidate
Member Candidate
Posts: 234
Joined: Sat Apr 30, 2011 3:11 am

Re: mAP Lite Ethernet susceptible to interference!

Tue May 24, 2016 3:59 pm

ok let me ask this a different way, is there anyone on this thread or who owns one, who DOESN"T have this problem?
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26287
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: mAP Lite Ethernet susceptible to interference!

Tue May 24, 2016 4:16 pm

Not sure about this thread, but just let me remind you, that nobody goes into the forum for posting something that works. People come to the forum to post about their problems. This thread has 31 posts.
 
Sob
Forum Guru
Forum Guru
Posts: 9119
Joined: Mon Apr 20, 2009 9:11 pm

Re: mAP Lite Ethernet susceptible to interference!

Tue May 24, 2016 6:47 pm

To help fellow user with interrogation ;), are you saying that these troubled mAP Lites are only few bad units? The ones you have available for yourself to play with work fine, there's no trouble with ethernet speed negotiation even if you stick them on big metal rack using the magnet, and no noticeable noice even when you push 100Mbit through wireless. And if people go and buy new one, they have >99% chance to get trouble free unit? Is that so? Out of curiosity, any hints what's wrong with those units that don't work fine?
 
Zorro
Long time Member
Long time Member
Posts: 675
Joined: Wed Apr 16, 2014 2:43 pm

Re: mAP Lite Ethernet susceptible to interference!

Thu May 26, 2016 7:08 am

cable itself is more EMI-vulnerable(or become part of pollution itself, which is even more important, sadly :/) than connector.
but if you deploy STP or CAT7 cable(or one of those "improved 6a" cables with one-two-multiple screens(but weaker than on Cat7 somewhat and with weaker cable itself and skin effect/bandwidth)) you HAD TO ENSURE that also connectors are - Properly Shielded and grounded, connected to screen, not just routers and for thus - have sockets with screen/grounding 360'/around clock.
 
sup5
Member
Member
Posts: 359
Joined: Sat Jul 10, 2010 12:37 am

Re: mAP Lite Ethernet susceptible to interference!

Thu May 26, 2016 11:00 am

One thing looks suspicious.
Since approx. two to three weeks no online shop I could find has MAPlite on stock.
But I remember they were available before this timeframe.

So I assume they all sent back their MAPs to Mikrotik for inspection.
 
Mazutti
newbie
Posts: 27
Joined: Sat Jun 21, 2014 4:12 am

Re: mAP Lite Ethernet susceptible to interference!

Fri Jul 08, 2016 11:49 am

One thing looks suspicious.
Since approx. two to three weeks no online shop I could find has MAPlite on stock.
But I remember they were available before this timeframe.

So I assume they all sent back their MAPs to Mikrotik for inspection.
Sounds possible, since mAP Lite have never been available here in Brazil, and no distributor has any forecast as to when it will be. Hope it´s for the best.

Mazutti
 
solelunauno
Member Candidate
Member Candidate
Posts: 119
Joined: Mon Jul 16, 2012 7:00 pm
Location: Roseto Capo Spulico CS Italy
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Mon Jul 11, 2016 5:55 pm

I noticed the same problem using mAP lite with its iron plate with adhesive: mAP will stuck @ 10Mbps and it will not work. If it's installed far from iron surfaces, it works well.
 
darkprocess
Member Candidate
Member Candidate
Posts: 249
Joined: Fri Mar 20, 2015 1:16 pm

Re: mAP Lite Ethernet susceptible to interference!

Mon Jul 11, 2016 6:52 pm

I removed one magnet and now it works as it has to be.

Envoyé de mon SM-G925F en utilisant Tapatalk
 
ecylcje
just joined
Posts: 19
Joined: Thu Jul 31, 2014 7:36 pm

Re: mAP Lite Ethernet susceptible to interference!

Tue Apr 24, 2018 5:01 pm

Hi,

Is this magnetic interference issue still happening with mAP Lites. I bought my mAP lite 17/04/2018 and it has issues where the eth1 port goes down every so often (seemingly random).

I have removed the 'metal backing' plate for now and attached using 'blue tack', but I was just wondering whether I should still need to be doing this, or even considering opening up the mAP lite to removal the internal magnet. (Is opening it up easy to do - I know it breaks the warranty).

Thanks,

Chris
 
ecylcje
just joined
Posts: 19
Joined: Thu Jul 31, 2014 7:36 pm

Re: mAP Lite Ethernet susceptible to interference!

Tue Apr 24, 2018 7:37 pm

Update:

It has been running now for several hours without being attached to anything metallic, only via blue tack. The connection has been rock sold, whereas previously it was 'link' bouncing at least 2 to 3 times ever hour (or more).

I suspect either the issue is back or my MAP lite came from a supplier which had 2 year old stock (unlikely).

Thanks,

Chris
 
bazzer
Trainer
Trainer
Posts: 87
Joined: Sat Mar 07, 2009 11:51 pm
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Tue Apr 24, 2018 8:06 pm

Pop the lid and see if it has any metal shield plates over the magnets. if it hasn't, its an original MK 1 with the ether interference problem. I'll see if i can find a comparison picture i took when the MK2 came out to help.
 
bazzer
Trainer
Trainer
Posts: 87
Joined: Sat Mar 07, 2009 11:51 pm
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Tue Apr 24, 2018 9:22 pm

MK1 on the left (bottom), MK 2 on the right (top)
You do not have the required permissions to view the files attached to this post.
 
ecylcje
just joined
Posts: 19
Joined: Thu Jul 31, 2014 7:36 pm

Re: mAP Lite Ethernet susceptible to interference!

Wed Apr 25, 2018 7:07 pm

Hi,

Just as a reply to this. I contacted the seller and the stock is a maximum of 3 months old. So it should definitely be a MK2 version. I guess there are still issues.

I'm now just deciding whether to open it up and void the warranty or live with the 'blue-tack'. I suspect the blue-tack will win.

Note: There have been no issues since using the blue-tack.

Thanks to everyone,

Chris
 
User avatar
juliokato
Member Candidate
Member Candidate
Posts: 228
Joined: Mon Oct 26, 2015 4:27 pm
Location: Brazil

Re: mAP Lite Ethernet susceptible to interference!

Wed Apr 25, 2018 8:02 pm

Again mikrotik adjusts the product without at least providing some indication visible in part number or serial number. (like RevA or RevB)
We have to open the equipment to do a visual inspection of the product. (sad thing)
How much it costs to make a change on the labels?
 
bazzer
Trainer
Trainer
Posts: 87
Joined: Sat Mar 07, 2009 11:51 pm
Contact:

Re: mAP Lite Ethernet susceptible to interference!

Wed Apr 25, 2018 9:41 pm

I'm now just deciding whether to open it up and void the warranty or live with the 'blue-tack'.
If I recall I don't think there are any warranty labels by MT, unless your supplier sticks anything on
 
maszika
just joined
Posts: 2
Joined: Tue Apr 06, 2021 1:22 am

Re: mAP Lite Ethernet susceptible to interference!

Sat Apr 10, 2021 3:31 am

Hi,

i bought a Map Lite at Januar. This is HW REV 3. I have the following problem:

The unit powered over active POE Switch ( HIKVISION ), and when it mount with magnet on a DSC Alarm system box, i have problem with Ethernet speed ( very oft only 10 Mb ) and randomly reboot after 1-2 days. When i unmount from the metal box, i have no problem. As attachment i give 2 pictures, with magnet mount and without magnet mount.

What is the solution ? This is engineering fault ? I must unmount the magnets from inside, and use a double side tape for mount on DSC alarm case ?

I see on the PCB one coil, when i unmount the magnet at this side, i think i have no interference, or ?

Thanks, Maszi
You do not have the required permissions to view the files attached to this post.
Last edited by maszika on Sat Apr 10, 2021 3:35 am, edited 1 time in total.
 
indy
newbie
Posts: 25
Joined: Sun Mar 22, 2020 10:17 pm

Re: mAP Lite Ethernet susceptible to interference!

Sun Apr 25, 2021 4:18 pm

My recently bought MAP Lite suffers from the same problem, with the Ethernet port dropping down to 10Mbit or failing completely, when the device is stuck on metal.
Bit surprised since it is hardware revision 2 (with factory firmware v6.44.5 from July/2019), which supposedly fixed the issue?
 
maszika
just joined
Posts: 2
Joined: Tue Apr 06, 2021 1:22 am

Re: mAP Lite Ethernet susceptible to interference!

Mon Apr 26, 2021 12:14 am

Hi,

I found the problem and the solution:

The EMI interference is active on the Ethernet Magnetic Transformer chip ( SWAPNET NS681679 ), when the device is stuck on metal.

The solution in my case the halfmount of device on metal box. ( under Transformer chip no metal object ) The auto negotiation is immediately 100 Mbit/s full duplex, and very stable, no reboot etc.

See pictures...
You do not have the required permissions to view the files attached to this post.
 
VK7HSE
just joined
Posts: 2
Joined: Tue Aug 06, 2019 11:02 am

Re: mAP Lite Ethernet susceptible to interference!

Mon Apr 26, 2021 10:55 am

After reading this thread I checked the mAP Lite that I have stuck on the rack ear of the switch. The mAP Lite is setup as a low power access point for the RB3011UIAS-RM (RF power set to minimum) Anyway this was stuck to the rack ear and the chip mentioned, and yes the ethernet is at 10meg, I've made a short patch cable so that it hangs free from all metal and the ethernet is back to 100meg.

So yes this does suffer from interference when stuck to a metal surface, however has anyone used the supplied metal patch as this does add a slight height off the attached surface (possibly inconsequential) and it does not cover the chip.

So for now mine is just hanging out in front of the router!

Sent from my Pixel 4 XL using Tapatalk

 
OnMi
just joined
Posts: 1
Joined: Thu Mar 31, 2022 12:09 pm

Re: mAP Lite Ethernet susceptible to interference!

Fri Apr 01, 2022 11:52 pm

We confirm that even mAP Lite bought in 02/2022 (probably MK2) still suffers from EMI interference issue.
We encoutered exactly the same behaviour with dopped packets and failing ethernet connection on both mAPs we installed on metal surface.

We used solution described above -> removed right neodym magnet from the cover underneath the PCB.

Now everything returned back to fully functional state. Rock solid 100mbit full duplex connection without any packet loss.

Our version (probably MK2) contained additional metal shield underneath the PCB on right side (under SWAPNET NS681679 transformer chip), but was equiped with full size neodym magnets like MK1.

It's bit strange, that mAP Lite issue with EMI interferrence issue described in 2016 is not still fully settled in 2022.

Note: it seems, that cAP Lite uses exactly the same board. But cAP Lite has just surface mounted cover with two screws (no magnets) and uses aluminium heat spreader underneath the PCB. We never encountered such issue on cAP Live. So it seems, that source of the issue is magnetic field produced by neodym magnets.

Who is online

Users browsing this forum: No registered users and 26 guests