Hello Everybody!
Its my first post on this forum, but I am with MT from 2.8.x version.
My question is:
Is QinQ vlans supported in CRS317-1G-16S+RM?
In specs is 801.Q only...
Re: CRS 317 support 802.1ad QinQ
+1 - I would presume it supports it??
Re: CRS 317 support 802.1ad QinQ
I have reply from support@mt: Does not support vlan-in-vlan.
Re: CRS 317 support 802.1ad QinQ
CRS317-1G-16S+RM currently does not support QinQ VLANs in switch chip (hardware support).
You can currently configure it through VLANs:
https://wiki.mikrotik.com/wiki/Manual:I ... LAN#Q-in-Q
802.1ad is a bridge standard so we must extend our bridge implementation to support it in hardware (though switch chip). We are working on it, it will be added in future versions.
You can currently configure it through VLANs:
https://wiki.mikrotik.com/wiki/Manual:I ... LAN#Q-in-Q
802.1ad is a bridge standard so we must extend our bridge implementation to support it in hardware (though switch chip). We are working on it, it will be added in future versions.
Re: CRS 317 support 802.1ad QinQ
So it does not support this? https://wiki.mikrotik.com/wiki/Manual:C ... 8Q-in-Q.29CRS317-1G-16S+RM currently does not support QinQ VLANs in switch chip (hardware support).
You can currently configure it through VLANs:
https://wiki.mikrotik.com/wiki/Manual:I ... LAN#Q-in-Q
802.1ad is a bridge standard so we must extend our bridge implementation to support it in hardware (though switch chip). We are working on it, it will be added in future versions.
Re: CRS 317 support 802.1ad QinQ
Doing QinQ in Software on a CRS317 is not very efficient though, when it comes to 10Gbit/s traffic. At 1-2 Gbit/s traffic, we'll be at CPU maximum.
Where are we with this supporting QinQ in the new configuration style ?
/M
Where are we with this supporting QinQ in the new configuration style ?
/M
Re: CRS 317 support 802.1ad QinQ
Aren't the QinQ a switch chip feature? I thought it was done by hardware, not involving the CPU.Doing QinQ in Software on a CRS317 is not very efficient though, when it comes to 10Gbit/s traffic. At 1-2 Gbit/s traffic, we'll be at CPU maximum.
Where are we with this supporting QinQ in the new configuration style ?
/M
Re: CRS 317 support 802.1ad QinQ
Aren't the QinQ a switch chip feature? I thought it was done by hardware, not involving the CPU.
Please read back in the thread and you'll realise, that Mikrotik stated, that the chip feature is not exposed to winbox yet and it has to be done in software until such time.CRS317-1G-16S+RM currently does not support QinQ VLANs in switch chip (hardware support).
You can currently configure it through VLANs:
https://wiki.mikrotik.com/wiki/Manual:I ... LAN#Q-in-Q
802.1ad is a bridge standard so we must extend our bridge implementation to support it in hardware (though switch chip). We are working on it, it will be added in future versions.
/M
Re: CRS 317 support 802.1ad QinQ
Is it still true that Q-in-Q is not supported with firmware 6.41rc5*
Re: CRS 317 support 802.1ad QinQ
Only in software. (Meaning CPU)Is it still true that Q-in-Q is not supported with firmware 6.41rc5*
Hardware is not configurable yet.
/M
Sent from my SM-G930F using Tapatalk
Re: CRS 317 support 802.1ad QinQ
as we are approaching v6.42 is no-QinQ-in-hardware still the case with the upcoming release?
-
-
viteaglavan
just joined
- Posts: 1
- Joined:
Re: CRS 317 support 802.1ad QinQ
Hi guys,
I'm new to this forum
Could you please explain how can I set TPID for vlan interface with 'use service tag' marked?
As far as I understood it uses the 0x88A8 for service tag, and 0x8100 for inner tag.
I need the ability to select service tag TPID values between 0x88A8 | 0x9100 | 0x8100
I'm new to this forum
Could you please explain how can I set TPID for vlan interface with 'use service tag' marked?
As far as I understood it uses the 0x88A8 for service tag, and 0x8100 for inner tag.
I need the ability to select service tag TPID values between 0x88A8 | 0x9100 | 0x8100
You do not have the required permissions to view the files attached to this post.
Re: CRS 317 support 802.1ad QinQ
Hello, by default VLAN interface uses and accepts encapsulation with TPID 0x8100. If "use-service-tag" option is enabled, then VLAN interface uses TPID 0x88A8. TPID 0x9100 is not supported in VLAN interfaces.
Re: CRS 317 support 802.1ad QinQ
As other people wonder - Are we/Have we gotten hardware support for QinQ?
Re: CRS 317 support 802.1ad QinQ
Doesn't look like it, though the Marvell 98DX8216 is a metro chipset (marvell's words) which would suggest 802.1ad should be available at the HW level.As other people wonder - Are we/Have we gotten hardware support for QinQ?
But my guess is we won't see this with this HW.
regards,
hk
Re: CRS 317 support 802.1ad QinQ
It is available sinc 6.43rc13
*) crs3xx - added initial Q-in-Q hardware offloading support (CLI only)
*) crs3xx - added initial Q-in-Q hardware offloading support (CLI only)
Who is online
Users browsing this forum: Bing [Bot] and 33 guests