i try to connect my RB3011 to a switch by cisco sfp fiber modules:
Code: Select all
[admin@MikroTik] /interface ethernet> monitor
numbers: sfp1
name: sfp1
status: no-link
auto-negotiation: done
advertising:
link-partner-advertising:
sfp-module-present: yes
sfp-rx-loss: no
sfp-tx-fault: no
sfp-type: SFP-or-SFP+
sfp-connector-type: LC
sfp-link-length-50um: 550m
sfp-link-length-62um: 550m
sfp-vendor-name: CISCO
sfp-vendor-part-number: SFP-GE-SX
sfp-vendor-revision: 1.0
sfp-vendor-serial: 1134705697
sfp-manufacturing-date: 13-11-28
sfp-wavelength: 850nm
sfp-temperature: 37C
sfp-supply-voltage: 3.317V
sfp-tx-bias-current: 6mA
sfp-tx-power: -5.803dBm
sfp-rx-power: -6.657dBm
eeprom-checksum: good
eeprom: 0000: 03 04 07 00 00 00 01 00 00 00 00 01 0d 00 00 00 ........ ........
0010: 37 37 00 00 43 49 53 43 4f 20 20 20 20 20 20 20 77..CISC O
0020: 20 20 20 20 00 20 20 20 53 46 50 2d 47 45 2d 53 . SFP-GE-S
0030: 58 20 20 20 20 20 20 20 31 2e 30 20 03 52 00 1a X 1.0 .R..
0040: 00 1a 00 00 31 31 33 34 37 30 35 36 39 37 20 20 ....1134 705697
0050: 20 20 20 20 31 33 31 31 32 38 20 20 58 90 01 3e 1311 28 X..>
0060: 00 00 11 f7 8c d1 89 6b d4 07 74 98 7d 16 12 b1 .......k ..t.}...
0070: 49 0f 4b 00 00 00 00 00 00 00 00 00 9f e6 6b 65 I.K..... ......ke
0080: 5f 00 ec 00 55 00 f6 00 8c a0 75 30 88 b8 79 18 _...U... ..u0..y.
0090: 1d 4c 00 00 13 88 01 f4 18 a5 03 e8 13 93 04 ea .L...... ........
00a0: 1f 07 00 3f 13 93 00 64 00 00 00 00 00 00 00 00 ...?...d ........
00b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ........ ........
00c0: 00 00 00 00 3f 80 00 00 00 00 00 00 01 00 00 00 ....?... ........
00d0: 01 00 00 00 01 00 00 00 01 00 00 00 00 00 00 9f ........ ........
00e0: 25 c8 81 98 0c 60 0a 44 0b 4a 00 00 00 00 02 f8 %....`.D .J......
00f0: 01 40 00 00 05 40 00 00 00 00 00 00 00 00 00 00 .@...@.. ........
When i plug in the sfp the mikrotik becoms unreachable on all (not only switch 2) ethernet ports. then i have to reconnect the lan cables. Sometimes 10 times till i can access the switch again. Sometimes i have to reboot.
Confugration is default.
FW is 6.42.7
May i got an defective rb3011? i just ordered it.
BR
mode