Community discussions

 
Mikrotikate
just joined
Topic Author
Posts: 7
Joined: Wed Feb 18, 2015 11:09 pm

RB4011 Metal temperature is really hot

Wed Mar 27, 2019 5:35 pm

Hello all,

I recently bough a new RB4011iGS+5HacQ2HnD-IN and before i had the chance to configure it, the metal became extremely hot ( just at the point of burning your hands ) and we still haven't reached this summer..
I understand this is to dissipate the heat but i would like to ask two questions as i am considering returning it:

1. Is it possible ( currently or in a near future ) to lower the CPU frequency with RouterOS or make some other configuration to prevent it from heating this much.
2. is everyone having the same experience?

Thanks!
 
User avatar
Etz
Member Candidate
Member Candidate
Posts: 152
Joined: Thu Mar 27, 2014 10:09 am
Location: Estonia

Re: RB4011 Metal temperature is really hot

Wed Mar 27, 2019 6:37 pm

Interesting, mine is not gtting hot at all, despite being fitted into very tight place with no ventilation and serving 500/500 connection, switching local network (over cpu, switch chips are crap on this), vpn, etc...

ImageImage

Under Health, it reports ~45C as temp and it is not definitely "hot" to touch...but this is non-wireless model, maybe radios are generating lot of heat? :?

OT: I really love form factor of this model, there is no way, I could have fit 8 port switch + ISP "generic consumer" router into that space.
 
User avatar
pcunite
Forum Veteran
Forum Veteran
Posts: 945
Joined: Sat May 25, 2013 5:13 am
Location: USA

Re: RB4011 Metal temperature is really hot

Wed Mar 27, 2019 11:40 pm

I have the non-wifi model. System/Health reports 40C. Another model I manage shows the same.
 
Mikrotikate
just joined
Topic Author
Posts: 7
Joined: Wed Feb 18, 2015 11:09 pm

Re: RB4011 Metal temperature is really hot

Wed Mar 27, 2019 11:55 pm

Thank you for your input. It would also be really nice to have other RB4011iGS+5HacQ2HnD-IN users reply. I don't see how the radio card alone can generate this much heat.

I am really considering returning it...
I have 2 hAP ac which I really enjoy, and they really excel in many ways and are always at ambient temperature..
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 23998
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RB4011 Metal temperature is really hot

Thu Mar 28, 2019 1:06 pm

That is completely normal and is to be expected. The RB4011 is designed to act as a heatsink.
No answer to your question? How to write posts
 
Mikrotikate
just joined
Topic Author
Posts: 7
Joined: Wed Feb 18, 2015 11:09 pm

Re: RB4011 Metal temperature is really hot

Thu Mar 28, 2019 9:29 pm

Thanks normis,

Could you comment also on my first question?
That is, if I don't want it to heat this much how can I reduce the CPU frequency or other, by software means, in order to reduce heat even if that means lower performance?
Will this be possible/available for the RB4011iGS+5HacQ2HnD-IN?

Many thanks.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 23998
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RB4011 Metal temperature is really hot

Fri Mar 29, 2019 9:31 am

The device has a very high performance CPU and no active cooling, the enclosure is made to act as a heatsink. It is designed to be hot.
Without active cooling fans, you can't make it cooler. Even just running idle at low CPU frequency it will be hot.
No answer to your question? How to write posts
 
deanMKD1
Member
Member
Posts: 345
Joined: Fri Dec 12, 2014 12:06 am
Location: Macedonia
Contact:

Re: RB4011 Metal temperature is really hot

Fri Mar 29, 2019 1:03 pm

Almost al ARM based routers have a little higher temperature then normal as we can see on MISPBE devices. Even my hAP Ac2 have higher temperature then other devices i haved before. But i think its normal, and dont have downsides.
 
User avatar
sebastia
Forum Guru
Forum Guru
Posts: 1589
Joined: Tue Oct 12, 2010 3:23 am
Location: Antwerp, BE

Re: RB4011 Metal temperature is really hot

Fri Mar 29, 2019 2:21 pm

possibly shorter lifespan?
 
mada3k
Frequent Visitor
Frequent Visitor
Posts: 75
Joined: Mon Jul 13, 2015 10:53 am
Location: Sweden

Re: RB4011 Metal temperature is really hot

Fri Mar 29, 2019 8:15 pm

I'm sure it's designed to be placed laying down, so the air can pass through the fins.
Manages some CCR's, RB750Gr3, RB922 and wAP's
 
User avatar
chechito
Forum Guru
Forum Guru
Posts: 1651
Joined: Sun Aug 24, 2014 3:14 am
Location: Bogota Colombia
Contact:

Re: RB4011 Metal temperature is really hot

Sat Mar 30, 2019 5:18 pm

Hello all,

I recently bough a new RB4011iGS+5HacQ2HnD-IN and before i had the chance to configure it, the metal became extremely hot ( just at the point of burning your hands ) and we still haven't reached this summer..
I understand this is to dissipate the heat but i would like to ask two questions as i am considering returning it:

1. Is it possible ( currently or in a near future ) to lower the CPU frequency with RouterOS or make some other configuration to prevent it from heating this much.
2. is everyone having the same experience?

Thanks!
1. You are complaining but not sharing temp reported on system health menu, please share to have an objective view of the situation
2. RB4011 is not a tiny device like hAP AC2, this device have twice as much cpu clock and uses Heaviest Out of Order CPU so expect more power consumption then HEAT
3. Passive cooled devices are designed to work a little hotter that is normal but is important to provide proper air flow
4. Maybe this device is not right for your needs, dont expect the device to be changed just for you
5. Datasheet its very clear, Power consumption around 23 watt, passive cooled device, this device will not work cool as a 5-10 watt tiny device, very clear on specs, dont expect this device to work well on a confined situation
6. Product photos make obvious the cooling fins at the back, and venting holes downside, its very clear you have to ensure proper free airflow for this device
7. If you cant live with this situation Put and external fan and its done you will have better temperatures
 
netos
just joined
Posts: 2
Joined: Sun Apr 07, 2019 11:02 pm

Re: RB4011 Metal temperature is really hot

Sun Apr 07, 2019 11:10 pm

You can reduce the frequency by going to system-> routerboard-> settings-> cpu frequencu. When installed at 800 MHz and the 2.4Ghz WiFi is turned off, the temperature should stop at 37 C. This is idle. But I do not know how it will affect performance.
 
netos
just joined
Posts: 2
Joined: Sun Apr 07, 2019 11:02 pm

Re: RB4011 Metal temperature is really hot

Mon Apr 08, 2019 4:22 pm

Today I looked at the temperature on rb4011iGS + rm in idle 34 C. And on rb1100ahx4 the temperature is 40 c with zero loading. The rb1100ahx4 case is barely warm. there the radiator does not touch the hull, but in a dream it seems it should still be hot. Who checked them at 100% loading cpu? What are your temperatures?
 
np3a17868
just joined
Posts: 1
Joined: Sat Apr 20, 2019 8:03 am

Re: RB4011 Metal temperature is really hot

Sat Apr 20, 2019 8:17 am

Mine runs hot (IMHO too hot) to the touch as well. System heath reports around 45C during the day. Even without the 5GHz radio which I normally disable.
This 4011 replaced a 2011 few weeks ago. Temperature was never a concern on the 2011.

Noted per design the chassis will become hot. However, I think the designed chassis temperature is too high,.
 
User avatar
craigmitchell
just joined
Posts: 6
Joined: Sat Aug 18, 2012 6:30 pm

Re: RB4011 Metal temperature is really hot

Sat Apr 20, 2019 11:12 pm

Hi team, I was tasked to evaluate the RB4011 before investing in more units.

This unit feels warm to the touch, even at zero load/shutdown.

Our unit is running RouterOS/firmware 6.43.14

1) we performed a System > Reset Configuration
2) no clients connected with LAN or WLAN
3) the unit was tested sitting in an open space on a table top with at least 2m clearing in all directions
4) the ambient air temperature was 23.5°C


Test #1 - with the unit powered on, we measured the external temperature at different points on the metal casing at 5 minute intervals after boot:

Time after boot / case temp
5 mins / 28.4 °C
10 mins / 33.0 °C
15 mins / 35.3 °C
20 mins / 37.0 °C
25 mins / 37.8 °C
30 mins / 38.6 °C
35 mins / 39.0 °C
40 mins / 40.2 °C
45 mins / 40.2 °C
50 mins / 40.4 °C
55 mins / 40.8 °C
60 mins / 40.8 °C


Test #2 - logon to the unit (winbox) and shutdown the unit. Our expectations were that the temperature would drop to ambient room temperature as the unit was now powered down (but still connected to PSU):

Time after shutdown / case temp
1 hour / 43.0 °C
2 hours / 43.5 °C
3 hours / 44.5 °C
4 hours / 45.0 °C
10 hours / 45.0 °C


I would be very interested to hear if the above observations are expected?
Last edited by craigmitchell on Sun Apr 21, 2019 9:21 am, edited 2 times in total.
 
cdemers
Member Candidate
Member Candidate
Posts: 176
Joined: Sun Feb 26, 2006 3:32 pm
Location: Canada
Contact:

Re: RB4011 Metal temperature is really hot

Sun Apr 21, 2019 4:02 am

If the power is connected the cpu is still running, even when you issue a shutdown in routeros. It just does a unix halt all processes and sits there in an idle loop, there is no way for it to power down if it's like all the other routers i have seen.


Sent from my SM-A520W using Tapatalk

 
Nemesiz
just joined
Posts: 5
Joined: Mon Mar 04, 2013 9:35 pm

Re: RB4011 Metal temperature is really hot

Sat Jun 22, 2019 7:49 pm

My RB4011iGS+5HacQ2HnD is hot like potato. Is it 47C normal?
 
R1CH
Forum Veteran
Forum Veteran
Posts: 869
Joined: Sun Oct 01, 2006 11:44 pm

Re: RB4011 Metal temperature is really hot

Tue Jun 25, 2019 12:50 pm

Yes, Mikrotik devices have a history of running quite hot. So far I've seen no reports of actual problems caused by this, the CPUs are rated for very high temperatures. If your router is actually crashing or exhibiting other strange behavior as a result of the temperature then it's a problem.
 
User avatar
honzam
Forum Guru
Forum Guru
Posts: 2274
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: RB4011 Metal temperature is really hot

Tue Jun 25, 2019 6:47 pm

Our rb4011 now reports 52C and works...
LAN, FTTx, Wireless. ISP operator
 
User avatar
chechito
Forum Guru
Forum Guru
Posts: 1651
Joined: Sun Aug 24, 2014 3:14 am
Location: Bogota Colombia
Contact:

Re: RB4011 Metal temperature is really hot

Wed Jun 26, 2019 12:41 am

Hi team, I was tasked to evaluate the RB4011 before investing in more units.

This unit feels warm to the touch, even at zero load/shutdown.

Our unit is running RouterOS/firmware 6.43.14

1) we performed a System > Reset Configuration
2) no clients connected with LAN or WLAN
3) the unit was tested sitting in an open space on a table top with at least 2m clearing in all directions
4) the ambient air temperature was 23.5°C


Test #1 - with the unit powered on, we measured the external temperature at different points on the metal casing at 5 minute intervals after boot:

Time after boot / case temp
5 mins / 28.4 °C
10 mins / 33.0 °C
15 mins / 35.3 °C
20 mins / 37.0 °C
25 mins / 37.8 °C
30 mins / 38.6 °C
35 mins / 39.0 °C
40 mins / 40.2 °C
45 mins / 40.2 °C
50 mins / 40.4 °C
55 mins / 40.8 °C
60 mins / 40.8 °C


Test #2 - logon to the unit (winbox) and shutdown the unit. Our expectations were that the temperature would drop to ambient room temperature as the unit was now powered down (but still connected to PSU):

Time after shutdown / case temp
1 hour / 43.0 °C
2 hours / 43.5 °C
3 hours / 44.5 °C
4 hours / 45.0 °C
10 hours / 45.0 °C


I would be very interested to hear if the above observations are expected?

i think that people must hire better qualified personnel to do that kind of evaluations than you
 
User avatar
chechito
Forum Guru
Forum Guru
Posts: 1651
Joined: Sun Aug 24, 2014 3:14 am
Location: Bogota Colombia
Contact:

Re: RB4011 Metal temperature is really hot

Wed Jun 26, 2019 12:51 am

people please update your knowledge on modern IT


Current state of art hardware heats a lot more than rb4011, in most modern devices temperature climbs so high that devices are throtling lowering performance to keep temperature under control

there is many CPU working at temperatures as high as 90°C or more and this is considered "normal"

this device consumes 23watt that energy needs to go some where in form of heat

Never rains at everyone taste

Mikrotik makes and designs a solid, powerful, silent and passive cooled device

absent of mobile parts thus less prone to failure because of fan damage


Then

many people complaining about feels hotter

No way to make happy everyone
 
mkx
Forum Guru
Forum Guru
Posts: 2468
Joined: Thu Mar 03, 2016 10:23 pm

Re: RB4011 Metal temperature is really hot

Wed Jun 26, 2019 9:27 am

... passive cooled device
This.

A passive cooled device can't cool without larger temperature difference (between device and ambient).
BR,
Metod
 
chrismfz
just joined
Posts: 14
Joined: Sat Apr 07, 2007 6:27 am
Contact:

Re: RB4011 Metal temperature is really hot

Thu Jun 27, 2019 4:54 pm

Hexpoe on attic without insulation or ventilated / cooled. 3rd summer in a row.
They will survive.
Image
 
dakotabcn
newbie
Posts: 27
Joined: Thu Apr 21, 2016 11:16 pm

Re: RB4011 Metal temperature is really hot

Fri Jun 28, 2019 12:31 am

Hello
My RB4011 wifi version is VERY VERY hot, it is impossible to put your hand on, you burn!
I do not find this excessive temperature logical or normal, it is currently marking 51 degrees Celsius, this is not good, such a high temperature will end up damaging the hardware, and it is not a cheap device at all.
Mikrotik has tested this equipment in warm environments? currently in Barcelona (Spain) we are with a very strong heat wave, and I fear for the router, I have had several mikrotik routers (RB3011, RB951G, RB1100AGx4) and none gets so hot
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 23998
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RB4011 Metal temperature is really hot

Fri Jun 28, 2019 10:55 am

This is NOT TRUE. Please read the entire topic.
No answer to your question? How to write posts
 
User avatar
blue
Member Candidate
Member Candidate
Posts: 265
Joined: Sun Dec 12, 2004 1:48 pm
Location: Serbia

Re: RB4011 Metal temperature is really hot

Mon Jul 01, 2019 11:14 pm

Hello,

It's very warm in Serbia and my RB4011iGS+ blocked twice in 3 days. This time I put him in Librenms and last temp before crash was 66C. It was maybe higher, but 4011 didn't report it. I could ping device, but traffic stopped and only remote gsm reboot saved me from traveling to this remote location.

I will have to mount some kind of fan to it.

BR...
 
joegoldman
Member
Member
Posts: 474
Joined: Mon May 27, 2013 2:05 am

Re: RB4011 Metal temperature is really hot

Tue Jul 02, 2019 3:06 am

you need to buy hardware for the installation, not just for the specs. If you are working in hot environments with no natural airflow / air-con then you will need active cooling, so buy a model with active cooling (RB1100AHx4 would be my suggestion). There is more to product selection then just specs, ports and functionality.
 
User avatar
blue
Member Candidate
Member Candidate
Posts: 265
Joined: Sun Dec 12, 2004 1:48 pm
Location: Serbia

Re: RB4011 Metal temperature is really hot

Tue Jul 02, 2019 9:41 am

you need to buy hardware for the installation, not just for the specs. If you are working in hot environments with no natural airflow / air-con then you will need active cooling, so buy a model with active cooling (RB1100AHx4 would be my suggestion). There is more to product selection then just specs, ports and functionality.
You are completely right! I didn't think about that potential issue :(
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 23998
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RB4011 Metal temperature is really hot

Tue Jul 02, 2019 10:05 am

I don't think the crash was due to temperature. The device can easily work at higher temperatures. make a supout.rif file and contact support, it could be another reason
No answer to your question? How to write posts
 
matiss
MikroTik Support
MikroTik Support
Posts: 3
Joined: Fri Dec 30, 2016 10:13 am

Re: RB4011 Metal temperature is really hot

Tue Jul 02, 2019 1:00 pm

you will need active cooling, so buy a model with active cooling (RB1100AHx4 would be my suggestion).
Be careful choosing device, both RB1100AHx4 models have passive cooling!
 
joegoldman
Member
Member
Posts: 474
Joined: Mon May 27, 2013 2:05 am

Re: RB4011 Metal temperature is really hot

Tue Jul 02, 2019 2:27 pm

you will need active cooling, so buy a model with active cooling (RB1100AHx4 would be my suggestion).
Be careful choosing device, both RB1100AHx4 models have passive cooling!
Hrmm i swear I remember fan holes on the back of 1100 case - maybe im thinking older model? My bad.
 
nmt1900
just joined
Posts: 24
Joined: Wed Feb 01, 2017 12:36 am

Re: RB4011 Metal temperature is really hot

Tue Jul 02, 2019 3:24 pm

RB1100AHx2 was last one with fans.
 
User avatar
blue
Member Candidate
Member Candidate
Posts: 265
Joined: Sun Dec 12, 2004 1:48 pm
Location: Serbia

Re: RB4011 Metal temperature is really hot

Tue Jul 02, 2019 6:45 pm

I don't think the crash was due to temperature. The device can easily work at higher temperatures. make a supout.rif file and contact support, it could be another reason
OK. I will do that. Thanks...
 
User avatar
chechito
Forum Guru
Forum Guru
Posts: 1651
Joined: Sun Aug 24, 2014 3:14 am
Location: Bogota Colombia
Contact:

Re: RB4011 Metal temperature is really hot

Wed Jul 03, 2019 1:02 am

you will need active cooling, so buy a model with active cooling (RB1100AHx4 would be my suggestion).
Be careful choosing device, both RB1100AHx4 models have passive cooling!
Hrmm i swear I remember fan holes on the back of 1100 case - maybe im thinking older model? My bad.
case has fan holes but not fans, only 20 watt no need for active cooling but maybe you can adapt a fan
 
Docop
just joined
Posts: 17
Joined: Thu May 23, 2019 3:56 pm

Re: RB4011 Metal temperature is really hot

Sun Jul 07, 2019 3:21 pm

Hot.. quite interesting. No one told about real data, just 1 post and don't know with what device it was took. My ex cry about everything is cold and me i was cooking. My rb in system health is at 40dC, room temp at 28.5 quite hot. And with a termocouple K type, a 1/8 of it, i can get a case temp of 22. it's about 0.5 feet from the floor.
But at same time, if you do multiple vlan and pass all the traffic of multiple network and so, you tax the unit. The rb4011 is not intend for a big buiseness and they do have bigger crs series for that.
 
User avatar
blue
Member Candidate
Member Candidate
Posts: 265
Joined: Sun Dec 12, 2004 1:48 pm
Location: Serbia

Re: RB4011 Metal temperature is really hot

Wed Jul 10, 2019 10:12 pm

Hello,

It's very warm in Serbia and my RB4011iGS+ blocked twice in 3 days. This time I put him in Librenms and last temp before crash was 66C. It was maybe higher, but 4011 didn't report it. I could ping device, but traffic stopped and only remote gsm reboot saved me from traveling to this remote location.

I will have to mount some kind of fan to it.

BR...
4011 blocked again, and weather is cold in Serbia. So blocking wasn't temperature related. I am changing it tomorrow for CCR1009-7G-1C-1S+
I sent supout again, and hopefully MTK will find what is wrong whit it.

BR,,,

Who is online

Users browsing this forum: No registered users and 14 guests