Page 1 of 1

waP R movil+ (Panama) problem "Not camped on cell"

Posted: Tue Aug 20, 2019 8:41 pm
by m0ntana
Hi!
I'm in Panama and trying to get work Movil+ sim card.
Here is what i can see debugging LTE:
After enabling it:
12:39:54 echo: lte,async lte1: sent ATE0
12:39:54 echo: lte,async lte1: rcvd OK
12:39:54 echo: lte,async lte1: sent AT+CFUN=0,1
12:39:54 echo: lte,async lte1: rcvd OK
[admin@MikroTik] /interface lte>
12:40:13 echo: lte,async lte1: sent ATE0
[admin@MikroTik] /interface lte>
(7 messages discarded)
12:40:15 echo: lte,async lte1: sent AT+CREG=2
12:40:15 echo: lte,async lte1: rcvd OK
12:40:15 echo: lte,async lte1: sent AT+CGREG=2
12:40:15 echo: lte,async lte1: rcvd +CME ERROR: operation not supported
12:40:15 echo: lte,async lte1: sent AT+CEREG=2
12:40:15 echo: lte,async lte1: rcvd OK
12:40:15 echo: lte,async lte1: sent AT+CGEREP=2,0
12:40:15 echo: lte,async lte1: rcvd OK
12:40:15 echo: lte,async lte1: sent AT+CMGF=0
12:40:15 echo: lte,async lte1: rcvd OK
12:40:15 echo: lte,async lte1: sent AT+CNMI=1,1,0,1,0
12:40:15 echo: lte,async lte1: rcvd OK
[admin@MikroTik] /interface lte>
12:40:16 echo: lte,async lte1: sent AT+CPIN?
12:40:16 echo: lte,async lte1: rcvd +CPIN: READY
12:40:16 echo: lte,async lte1: sent AT+CFUN=1
12:40:16 echo: lte,async,raw +CEREG: 2
12:40:16 echo: lte,async lte1: rcvd OK
[admin@MikroTik] /interface lte>
12:40:20 echo: lte,async lte1: sent AT+CPMS="SM","SM","SM"
12:40:20 echo: lte,async lte1: rcvd +CPMS: 0,30,0,30,0,30
12:40:20 echo: lte,async lte1: sent AT+CFUN?
12:40:20 echo: lte,async lte1: rcvd +CFUN: 1
12:40:20 echo: lte,async lte1: sent AT+CNUM
12:40:20 echo: lte,async lte1: rcvd
12:40:20 echo: lte,async lte1: sent AT+CIMI
12:40:20 echo: lte,async lte1: rcvd 714011001705705
12:40:20 echo: lte,async lte1: sent AT+CPIN?
12:40:20 echo: lte,async lte1: rcvd +CPIN: READY
12:40:20 echo: lte,async lte1: sent AT%PDNSET=1,"apn01.cwpanama.com.pa","IP","NONE","",""
12:40:20 echo: lte,async lte1: rcvd OK
[admin@MikroTik] /interface lte>
12:40:21 echo: lte,async lte1: sent at%cmatt=1
12:40:21 echo: lte,async lte1: rcvd OK
12:40:21 echo: lte,debug lte1: config ok
12:40:21 echo: lte,async,raw lte1: sent AT+CFUN?
12:40:21 echo: lte,async,raw lte1: rcvd +CFUN: 1
12:40:21 echo: lte,async,raw lte1: sent AT%MEAS="7"
12:40:21 echo: lte,async,raw lte1: rcvd CQI: N/A
12:40:21 echo: lte,async,raw lte1: sent AT%MEAS="8"
12:40:21 echo: lte,async,raw lte1: rcvd Signal Quality: RSRP = N/A, RSRQ = N/A, SINR = N/A, RSSI = N/A
12:40:21 echo: lte,async,raw lte1: sent AT%PCONI
12:40:21 echo: lte,async,raw lte1: rcvd +CME ERROR: Not camped on cell
[admin@MikroTik] /interface lte>
12:40:24 echo: lte,async,raw lte1: sent AT%MEAS="7"
12:40:24 echo: lte,async,raw lte1: rcvd CQI: N/A
12:40:24 echo: lte,async,raw lte1: sent AT%MEAS="8"
12:40:24 echo: lte,async,raw lte1: rcvd Signal Quality: RSRP = N/A, RSRQ = N/A, SINR = N/A, RSSI = N/A
12:40:24 echo: lte,async,raw lte1: sent AT%PCONI
12:40:24 echo: lte,async,raw lte1: rcvd +CME ERROR: Not camped on cell
[admin@MikroTik] /interface lte>
12:40:27 echo: lte,async,raw lte1: sent AT%MEAS="7"
12:40:27 echo: lte,async,raw lte1: rcvd CQI: N/A
12:40:27 echo: lte,async,raw lte1: sent AT%MEAS="8"
12:40:27 echo: lte,async,raw lte1: rcvd Signal Quality: RSRP = N/A, RSRQ = N/A, SINR = N/A, RSSI = N/A
12:40:27 echo: lte,async,raw lte1: sent AT%PCONI
12:40:27 echo: lte,async,raw lte1: rcvd +CME ERROR: Not camped on cell
[admin@MikroTik] /interface lte>
12:40:30 echo: lte,async,raw lte1: sent AT%MEAS="7"
12:40:30 echo: lte,async,raw lte1: rcvd CQI: N/A
12:40:30 echo: lte,async,raw lte1: sent AT%MEAS="8"
12:40:30 echo: lte,async,raw lte1: rcvd Signal Quality: RSRP = N/A, RSRQ = N/A, SINR = N/A, RSSI = N/A
12:40:30 echo: lte,async,raw lte1: sent AT%PCONI
12:40:30 echo: lte,async,raw lte1: rcvd +CME ERROR: Not camped on cell
I have latest firmware: 6.45.3