Community discussions

 
User avatar
exebug
newbie
Topic Author
Posts: 43
Joined: Thu Jun 08, 2006 3:36 pm
Location: South Africa
Contact:

RB800 ether problem

Wed Jun 02, 2010 9:51 am

I have the following problem on a ether with no cable connected

Image

ROS version 4.8

If i dissable and enable the interface it begins doing it again after a few seconds.

Any Ideas as to what could be the problem ?
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24190
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RB800 ether problem

Wed Jun 02, 2010 9:58 am

doing what? where is the problem?
No answer to your question? How to write posts
 
aaa
Member
Member
Posts: 458
Joined: Mon Apr 11, 2005 11:54 am
Location: Latvia, Baltezers

Re: RB800 ether problem

Wed Jun 02, 2010 10:01 am

Why you rename ethernet interfaces? Do you have link LEDs on when no cable connected? It's remind ethernet swich port damage by lightning :))
 
User avatar
THG
Member
Member
Posts: 472
Joined: Thu Oct 15, 2009 1:05 am

Re: RB800 ether problem

Wed Jun 02, 2010 10:15 am

doing what? where is the problem?
Receive traffic at a rate of 220 Mbps without reason.

I've seen this on another RB800 with RouterOS 4.5.
Last edited by THG on Fri Jun 11, 2010 10:26 am, edited 1 time in total.
 
User avatar
exebug
newbie
Topic Author
Posts: 43
Joined: Thu Jun 08, 2006 3:36 pm
Location: South Africa
Contact:

Re: RB800 ether problem

Mon Jun 07, 2010 9:52 am

doing what? where is the problem?
Receive traffic at a rate of 220 Mbps without reason.
Yep exactly whats happening, no cable connected to the ethernet port, yet there is traffic runinng for
no reason
 
User avatar
sergejs
MikroTik Support
MikroTik Support
Posts: 6615
Joined: Thu Mar 31, 2005 3:33 pm
Location: Riga, Latvia
Contact:

Re: RB800 ether problem

Tue Jun 08, 2010 2:47 pm

Do you have the same information after upgrading router to MikroTik RouterOS to 4.10? and by upgrading firmware by,
/system routerboard upgrade
/system reboot
 
User avatar
exebug
newbie
Topic Author
Posts: 43
Joined: Thu Jun 08, 2006 3:36 pm
Location: South Africa
Contact:

Re: RB800 ether problem

Thu Jun 10, 2010 9:10 pm

Will give it a try end report back
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24190
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: RB800 ether problem

Fri Jun 11, 2010 8:58 am

we have fixed this problem, fix will be in next RouterOS releases.
No answer to your question? How to write posts
 
unfamous
just joined
Posts: 15
Joined: Sun Apr 27, 2008 8:46 am

Re: RB800 ether problem

Fri Jun 11, 2010 1:35 pm

we have fixed this problem, fix will be in next RouterOS releases.

I also have problems like that but with RB1100,

no cable plug - RX 220.1 Mb. autonegotiation failed.

and when I plug the cable from other modem/router/switch to RB1100 port 11, 12 or 13, router always stuck / every 5-10 minutes interface/ether always disconnect/down.

but port 1-10 is normal!.. is that bug or something??

firmware: "2.27"
version: "4.10"
 
User avatar
roc-noc.com
Forum Veteran
Forum Veteran
Posts: 869
Joined: Sun Dec 02, 2007 3:27 am
Location: Rockford, IL USA
Contact:

Re: RB800 ether problem

Fri Jun 11, 2010 6:06 pm

we have fixed this problem, fix will be in next RouterOS releases.
Please release this fixed version soon. We have many customers putting these into production routing most of their traffic.

Tom
-----------------------------------------------
http://www.roc-noc.com
Tom, CCNA, ISP, USA Mikrotik Distributor
888-762-5662
-----------------------------------------------

Who is online

Users browsing this forum: No registered users and 3 guests