Community discussions

MikroTik App
 
elmer
newbie
Topic Author
Posts: 40
Joined: Mon Jun 18, 2012 4:02 pm

RB333 with replaced LAN chip.

Mon Jun 18, 2012 4:08 pm

Hello! After repair LAN of RB333 i want to update firmware / software, but after install RB won`t boot :(

In console i`ll see this:
MikroTik 5.17
MikroTik Login: Oops: Kernel access of bad area, sig: 11 [#1]
RB333/RB600
last sysfs file: /sys/bus/spi/uevent
NIP: 85366ae8 LR: 85366cf0 CTR: 801c387c
REGS: 83b0dc30 TRAP: 0300   Tainted: P             (2.6.35)
MSR: 00009032 <EE,ME,IR,DR>  CR: 24822042  XER: 20000000
DAR: 00000004, DSISR: 20000000
TASK = 83a20800[235] 'net' THREAD: 83b0c000
GPR00: 85366cf0 83b0dce0 83a20800 00000000 802bc704 80298b4c 801c3868 00000000
GPR08: 00000001 00000000 83b0dbd0 801c387c 84822042 100e5590 301653a8 00000000
GPR16: 100c8ea8 00000000 20000000 83aded68 83adeb98 80320000 83aded30 83adeb08
GPR24: 20000000 00000001 00000200 00000000 83ade800 85364264 83adeb14 83adeb00
NIP [85366ae8] init_flow_control_params+0x1bb0/0x25c0 [ucc_geth@0x85363000]
LR [85366cf0] init_flow_control_params+0x1db8/0x25c0 [ucc_geth@0x85363000]
Call Trace:
[83b0dce0] [85366cf0] init_flow_control_params+0x1db8/0x25c0 [ucc_geth@0x853630)
[83b0dda0] [801d9c44] __dev_open+0xf0/0x13c
[83b0ddc0] [801d9ef0] __dev_change_flags+0xa0/0x198
[83b0dde0] [801da09c] dev_change_flags+0x1c/0x64
[83b0de00] [8022a9f0] devinet_ioctl+0x714/0x7f8
[83b0de70] [8022bd4c] inet_ioctl+0xcc/0xf8
[83b0de80] [801c59b4] sock_ioctl+0x64/0x2a4
[83b0dea0] [800a35b0] do_vfs_ioctl+0xa4/0x754
[83b0df10] [800a3ca0] sys_ioctl+0x40/0x74
[83b0df40] [800113ec] ret_from_syscall+0x0/0x38
--- Exception: c01 at 0x3011436c
    LR = 0x30039b1c
Instruction dump:
88e6010c 38c6010d 48001591 813c0300 7f83e378 7fa5eb78 80ff0290 38c00000
80890108 48001485 7c7b1b79 418201fc <807b0004> 38c00000 38a00000 809b00c8
---[ end trace f853320fb30e439f ]---
PHY: mdio@e0103120:01 - Link is Up - 100/Full
On RouterOS 4.17 don`t have this problem, for now i cannot access the board, netinstall dont work.
Can i do something by myself to get this RB works again? fwf via RS-232 dont resolve problem.

Who is online

Users browsing this forum: No registered users and 16 guests