Community discussions

MikroTik App
  4. Other topics
  5. RouterBOARD hardware

RB2011UAS-2HnD Graphing

Post Reply
 
DragonSlayer
newbie
Topic Author
Posts: 25
Joined: Tue Sep 25, 2012 9:14 am
Location: Sweden

RB2011UAS-2HnD Graphing

Thu Sep 12, 2013 11:59 am

I don't get any graphs on eth7-eth10 ports
RouterOS 6.3
Firmware 3.08
Code: Select all
/interface print
Flags: D - dynamic, X - disabled, R - running, S - slave 
 #     NAME                                TYPE         MTU L2MTU  MAX-L2MTU MAC-ADDRESS      
 0  RS FE6-HomePlug                        ether       1500  1598       2028 D4:CA:6D:97:8C:F2
 1  RS FE7-U5                              ether       1500  1598       2028 D4:CA:6D:97:8C:F3
 2   S FE8                                 ether       1500  1598       2028 D4:CA:6D:97:8C:F4
 3   S FE9                                 ether       1500  1598       2028 D4:CA:6D:97:8C:F5
 4   S FE10                                ether       1500  1598       2028 D4:CA:6D:97:8C:F6
 5  R  G1-WAN                              ether       1500  1598       4074 D4:CA:6D:97:8C:ED
 6  RS G2-LAN                              ether       1500  1598       4074 D4:CA:6D:97:8C:EE
 7  RS G3-NAS                              ether       1500  1598       4074 D4:CA:6D:97:8C:EF
 8   S G4                                  ether       1500  1598       4074 D4:CA:6D:97:8C:F0
 9   S G5                                  ether       1500  1598       4074 D4:CA:6D:97:8C:F1
10     SFP                                 ether       1500  1598       4074 D4:CA:6D:97:8C:EC
11   S WLAN                                wlan        1500  2290            D4:CA:6D:97:8C:F7
12  R  bridge-local                        bridge      1500  1598            D4:CA:6D:97:8C:EE
Also i only get Tx & Rx values on eth6 in the Interface List

How do i configure it to work
Top
 
User avatar
pcunite
Forum Guru
Forum Guru
Posts: 1345
Joined: Sat May 25, 2013 5:13 am
Location: USA

Re: RB2011UAS-2HnD Graphing

Thu Sep 12, 2013 7:12 pm

The newest version, v6.4, adjusts some issues with graphs. Perhaps you should try that version.
http://www.mikrotik.com/download
Top
 
DragonSlayer
newbie
Topic Author
Posts: 25
Joined: Tue Sep 25, 2012 9:14 am
Location: Sweden

Re: RB2011UAS-2HnD Graphing

Thu Sep 12, 2013 9:41 pm

actually it has nothing to do with graphing.

Just updated to 6.4 and rebooted (Graphing data stayed in place, was not deleted)

eth6 records data even if i dont have anything connected to that slot
i guess it has something to do with the switch, only recording on the master port.

so how can i get recorded data on the Fast Ethernet switch (eth6 - eth10)?
Top
 
Neilson
Member Candidate
Member Candidate
Posts: 174
Joined: Tue Nov 06, 2012 10:42 pm
Location: Auckland, New Zealand

Re: RB2011UAS-2HnD Graphing

Sat Sep 14, 2013 7:03 am

If I understand correctly the switch chip in that device only reports aggregate totals. That is why the figures only report on the master port.

I believe I have seen at least one device that will show the details per port (but I can't remember where I saw it). Otherwise its only aggregation.

If you wanted to see the per port then I would expect you would have to use software bridging. With the advantages of FastPath you may be able to use that to keep an adequate performance level up for your application.

Otherwise I don't think there is a way to see it. May be a good feature request for Mikrotik (maybe even implemented in the CRS as thats a single switch chip) but it would have to be data available to be read off the switch chip itself as diagnostic output.

Regards
Alexander
Top
 
DragonSlayer
newbie
Topic Author
Posts: 25
Joined: Tue Sep 25, 2012 9:14 am
Location: Sweden

Re: RB2011UAS-2HnD Graphing

Sun Sep 15, 2013 12:40 am

Yest that is true.. port eth1-eth5 show everything on each port, while eth6 shows everything on eth6-eth10
Top
 
DragonSlayer
newbie
Topic Author
Posts: 25
Joined: Tue Sep 25, 2012 9:14 am
Location: Sweden

Re: RB2011UAS-2HnD Graphing

Thu Sep 19, 2013 9:55 pm

SOLVED:

This is what i did (im not an advanced RouterOs user)
everyting was done via Winbox:

Open Interfaces and go to the tab "Interface"
Dubbleclick on your eth7 interface
go to the tab "General"
Select the value "None" for the "Master Port" setting
Click OK

Open Bridge and go to the tab "Ports"
press the plus sign [+]
Select the value for your eth7 interface for the "Interface"
Click OK

Repeat for eth8, eth9 and eth10
Done
Top
 
JackANSI
Frequent Visitor
Frequent Visitor
Posts: 71
Joined: Wed Apr 03, 2013 6:52 pm

Re: RB2011UAS-2HnD Graphing

Mon Sep 23, 2013 6:36 pm

Dup....
Last edited by JackANSI on Mon Sep 23, 2013 6:38 pm, edited 1 time in total.
Top
 
JackANSI
Frequent Visitor
Frequent Visitor
Posts: 71
Joined: Wed Apr 03, 2013 6:52 pm

Re: RB2011UAS-2HnD Graphing

Mon Sep 23, 2013 6:38 pm

You're going to take a performance hit when any of the ports 6-10 have to talk to each other with that config, just an FYI.
Top
 
DragonSlayer
newbie
Topic Author
Posts: 25
Joined: Tue Sep 25, 2012 9:14 am
Location: Sweden

Re: RB2011UAS-2HnD Graphing

Mon Sep 30, 2013 11:39 pm

another solution is welcome :?
Top
 
User avatar
janisk
MikroTik Support
MikroTik Support
Posts: 6263
Joined: Tue Feb 14, 2006 9:46 am
Location: Riga, Latvia

Re: RB2011UAS-2HnD Graphing

Tue Oct 01, 2013 10:36 am

wait for RouterOS 6.5 release. When you get that, set FE ports master-port back to ether6. Or if you know where to get 6.5rc1 pre-release that already have this feature.
Top
Post Reply

Who is online

Users browsing this forum: No registered users and 14 guests
  4. Other topics
  5. RouterBOARD hardware