Community discussions

 
littlebill
Member Candidate
Member Candidate
Topic Author
Posts: 231
Joined: Sat Apr 30, 2011 3:11 am

Map2n boot firmware and various issues

Sun Sep 07, 2014 2:15 am

normally the boot firmware is on routerboard.com, i don't see it for the MAP?


activity indicators for the Lan ports are a joke, they are about 5 seconds behind, even on a link establishment

then blink 5 seconds behind at a steady pace

the wireless LED activity indicator does not have this problem

found another bug

6.19

make eth 1 master, eth 2 slave, only plug a cable into eth 2, and eth 1 lights up and show a link status in winbox 10 mbit

very weird, reversing does not do the same thing, eth 2 will not light up, supout sent to mikrotik



also can the poe out be used, when usb is supplying (2 amps behind) or does it not have a boost circuit?

also when attempting to use POE out for a picostation, forced on was required to boot the pico up, it was blinking weird on auto on, also showed no link

also should i be seeing values in the below picture or just powered on?
You do not have the required permissions to view the files attached to this post.
 
User avatar
honzam
Forum Guru
Forum Guru
Posts: 2292
Joined: Wed Feb 27, 2008 10:27 pm
Location: Czech Republic

Re: Map2n boot firmware and various issues

Sun Sep 07, 2014 11:18 pm

CPU = Qualcomm Atheros AR9331 400 MHz

MIPS-BE - http://www.mikrotik.com/download
LAN, FTTx, Wireless. ISP operator
 
littlebill
Member Candidate
Member Candidate
Topic Author
Posts: 231
Joined: Sat Apr 30, 2011 3:11 am

Re: Map2n boot firmware and various issues

Mon Sep 08, 2014 1:15 am

CPU = Qualcomm Atheros AR9331 400 MHz

MIPS-BE - http://www.mikrotik.com/download

uh yea? im looking for the boot firmware, not the main code
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 24259
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: Map2n boot firmware and various issues

Mon Sep 08, 2014 2:15 am

RouterBOOT is always in the RouterOS "RouterBOARD" package. If you have an up to date RouterOS, simply run "/system RouterBOARD upgrade".

The FWF file is only important to devices with COM ports (but they can also upgrade with the mentioned command)
No answer to your question? How to write posts
 
littlebill
Member Candidate
Member Candidate
Topic Author
Posts: 231
Joined: Sat Apr 30, 2011 3:11 am

Re: Map2n boot firmware and various issues

Mon Sep 08, 2014 6:12 am

ok an answer to any of the other questions?
 
User avatar
janisk
MikroTik Support
MikroTik Support
Posts: 6283
Joined: Tue Feb 14, 2006 9:46 am
Location: Riga, Latvia

Re: Map2n boot firmware and various issues

Mon Sep 08, 2014 2:36 pm

via USB you can power only connected board, PoE-out is not available.
 
littlebill
Member Candidate
Member Candidate
Topic Author
Posts: 231
Joined: Sat Apr 30, 2011 3:11 am

Re: Map2n boot firmware and various issues

Tue Sep 09, 2014 11:39 pm

via USB you can power only connected board, PoE-out is not available.

how about the missing POE values in the screen shot?
 
User avatar
janisk
MikroTik Support
MikroTik Support
Posts: 6283
Joined: Tue Feb 14, 2006 9:46 am
Location: Riga, Latvia

Re: Map2n boot firmware and various issues

Wed Sep 10, 2014 10:26 am

it is not capable of showing power consumption.

only option is status, where you can see if connected device is powered on, or other internal statuses of PoE-Out

Who is online

Users browsing this forum: No registered users and 14 guests