$ ./iperf3 -c 192.168.x.11 -R
Connecting to host 192.168.x.11, port 5201
Reverse mode, remote host 192.168.x.11 is sending
[ 4] local 192.168.x.28 port 49430 connected to 192.168.x.11 port 5201
[ ID] Interval Transfer Bandwidth
[ 4] 0.00-1.00 sec 44.7 MBytes 375 Mbits/sec
[ 4] 1.00-2.00 sec 50.8 MBytes 426 Mbits/sec
[ 4] 2.00-3.00 sec 49.9 MBytes 419 Mbits/sec
[ 4] 3.00-4.00 sec 49.3 MBytes 414 Mbits/sec
[ 4] 4.00-5.00 sec 51.9 MBytes 435 Mbits/sec
[ 4] 5.00-6.00 sec 50.8 MBytes 426 Mbits/sec
[ 4] 6.00-7.00 sec 51.3 MBytes 430 Mbits/sec
[ 4] 7.00-8.00 sec 50.8 MBytes 426 Mbits/sec
[ 4] 8.00-9.00 sec 51.3 MBytes 430 Mbits/sec
[ 4] 9.00-10.00 sec 50.9 MBytes 427 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth
[ 4] 0.00-10.00 sec 504 MBytes 423 Mbits/sec sender
[ 4] 0.00-10.00 sec 502 MBytes 421 Mbits/sec receiver
$ ./iperf3 -c 192.168.x.11 -R
Connecting to host 192.168.x.11, port 5201
Reverse mode, remote host 192.168.x.11 is sending
[ 4] local 192.168.x.28 port 49508 connected to 192.168.x.11 port 5201
[ ID] Interval Transfer Bandwidth
[ 4] 0.00-1.00 sec 74.5 MBytes 625 Mbits/sec
[ 4] 1.00-2.00 sec 91.6 MBytes 769 Mbits/sec
[ 4] 2.00-3.00 sec 92.4 MBytes 775 Mbits/sec
[ 4] 3.00-4.00 sec 91.5 MBytes 767 Mbits/sec
[ 4] 4.00-5.00 sec 92.4 MBytes 775 Mbits/sec
[ 4] 5.00-6.00 sec 91.5 MBytes 767 Mbits/sec
[ 4] 6.00-7.00 sec 91.4 MBytes 767 Mbits/sec
[ 4] 7.00-8.00 sec 85.0 MBytes 713 Mbits/sec
[ 4] 8.00-9.00 sec 86.8 MBytes 728 Mbits/sec
[ 4] 9.00-10.00 sec 93.5 MBytes 784 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth
[ 4] 0.00-10.00 sec 893 MBytes 749 Mbits/sec sender
[ 4] 0.00-10.00 sec 892 MBytes 748 Mbits/sec receiver
Can you show me your exact configuration?The default config for the wireless should be pretty good. The only thing I changed on my hAP AC is locking the channel on 100 and enabling WMM. I get a consistent 1300mbps link, and smooth 350~375mbps throughput.
In CAPsMAN it is different. Channel width should be 20MHz and you should use Extension Channel setting to choose wide the total channel should be.I tried all the settings. Also following the list here: https://en.wikipedia.org/wiki/List_of_WLAN_channels
Always when I set 80MHz, stands unsupportet configuraton (Country: switzerland with CAPsMAN). So I ask for the configuration to see what I do wrong?
To get 1300mbps data-rate (not throughput) you need a client device capable of 3 spatial streamsI have already tried various (with CAPsMAN and without CAPsMAN), but I never get a link higher than the screenshot.
Can someone post a working configuration, with consistent 1300mbps link? The configuration can also be without CAPSMAN, If possible with country Switzerland.
5240/20-eeeC/ac/P(20dBm)
[ ID] Interval Transfer Bandwidth
[340] 0.0- 1.0 sec 8772 KBytes 71858 Kbits/sec
[340] 1.0- 2.0 sec 9626 KBytes 78852 Kbits/sec
[340] 2.0- 3.0 sec 10268 KBytes 84111 Kbits/sec
[340] 3.0- 4.0 sec 9717 KBytes 79605 Kbits/sec
[340] 4.0- 5.0 sec 9829 KBytes 80520 Kbits/sec
[340] 5.0- 6.0 sec 10169 KBytes 83301 Kbits/sec
[340] 6.0- 7.0 sec 10827 KBytes 88699 Kbits/sec
[340] 7.0- 8.0 sec 10831 KBytes 88730 Kbits/sec
[340] 8.0- 9.0 sec 9788 KBytes 80184 Kbits/sec
[340] 9.0-10.0 sec 11108 KBytes 91000 Kbits/sec
The default config for the wireless should be pretty good. The only thing I changed on my hAP AC is locking the channel on 100 and enabling WMM. I get a consistent 1300mbps link, and smooth 350~375mbps throughput.
Set it toPlease help me how to configure my wAP ac (RBwAPG-5HacT2HnD-BE) to run this same 1300 Mb (MAcBook) speed like in mentoned by IntrusDave?
Is this
country Switzerland.
5240/20-eeeC/ac/P(20dBm)???
The default config for the wireless should be pretty good. The only thing I changed on my hAP AC is locking the channel on 100 and enabling WMM. I get a consistent 1300mbps link, and smooth 350~375mbps throughput.
I'm not too much into mac but as far I know Mac Air doesn't have triple chain wifi, I had new Mac Air yesterday at work and it showed as dual chain in device manager, also connected 867mbitStill only 867 Mb.
How to fix setup up to 1200-1300Mb ?
@IntrusDave how to get Channel 100 on Mikrotik wAP ac ?
Check model specifications for wifi, not sure how to check under OSX, I installed windows as customer requested so it was easy to check under device manager..That is interesting. Friend of mine has same model same time and got 1200-1300 connection from Netgear 5G Router.
I just wondering where can I find this information in mac about WiFi card dual/triple ?
Well tell me what wifi chip model it has, simple Google will reveal its specs..I know where to check my MacOS device wifi spec, but I don't see over there this dual or triple wording.
Well it's strange, because mine air book clearely showed dual band ac under device manager sorry dont have it anymore around to check anything or tell you anything more useful.Apple tech spec for all 2015 Macbook Air shows
https://www.apple.com/macbook-air/features/
1300 Mbps !
Chipset : Broadcom BCM43xx
Did you manage to improve on this?Hi, I bought hAP AC and I have a question about 5GHz AC speed.
I have a good internet connection, 600-800Mbit+ DOWN/UP on wire, but I have problem with AC wireless speed.
After 2 days of testing I have such results:
Signal -55dBm, 3m from client - USB TP Link T4UH AC1200.
CCQ 92%
TX Rate 520Mbps-80Mhz/2S/SGI
RX Rate 866 Mbps-80Mhz/2S/SGI
As you can see below my ISP give me better upload than download.
But can someone tell me why download on WiFI is not as fast as upload?
WIFI:
Cable: