I am a beginner and faced some challenges during the process. Documenting my notes online, in case they may help someone else in the future. If you notice something that I could do that would improve my setup, please let me know.
Preface before I start:
My intention was to disable my 2.4 and 5.0 from my current router (Asus RT-N66U running tomato) and use the wap ac as an access point. Main reason being that my current router is placed in a terrible location. And moving the ugly black router to the living room was a no-go with the wife. She liked the idea of the wap ac, said it looked similar to an alarm bell box or fire detector, so no issues on that front.
So the goal was to continue using the tomato router to handle all dhcp and routing duties and use the wap ac as it's antenna basically. There are no fancy vlans or guest wireless networks in this setup. It's just making the wap ac work with my current router.
Directions to flash to the latest firmware:
Recover a Broken Mikrotik Device
New RB951G-2HnD bricked? [Solved with Netinstall]
Firmware that I used
Setup Blues (Winbox where is my device?)
Even after resetting to factory defaults I was not seeing the wireless network Mikrotik and unable to use winbox. On reddit, someone suggested that I put it into CAP mode and see if I could connect to it with winbox at that point. And it worked!!!! So I’m finally in.
Directions to put in CAP mode:
- Hard wire WAP to your computer
- Manually configure IP to 192.168.88.x subnet. Though I am not sure that is actually necessary. I believe it makes the connection using the MAC address.
- Hold reset button until 2.4/5 goes solid and release button when CAP starts blinking.
- Wait one minute for WAP to start up. Open winbox and check neighbor. You should see your WAP MAC address!
- Connect and you’re in!
- Once in, you have to get rid of the CAP mode. System – Reset Configuration. I checked No Default and Do Not Backup.
Resources that I used during the setup phase of the process:
Making a simple wireless AP
Configure your MikroTik router as an Access Point wireless router
(The two above resources, left me with wireless access, but no internet on those devices. Pings and such was working through terminal on winbox, but I was confused. Later I realized that ether1 was good, but not the wireless radios. Slept on it and figured it out in the morning.)
InstrusDave ethernet bridge setup - posted on the forums and helped me get over the hump and get wireless internet connectivity working. If I had seen this post initially, the whole setup would've taken 10 minutes. (Once I got into winbox at least!)
Time to setup the device:
- Wireless – go to security profile and create your WPA key. In my case, my 2.4 is different than my 5.0, so I created two.
- Wireless – go back to interfaces.
- Double click on name of one of the interfaces (one is 2.4 and other is 5.0)
- General tab – I changed the name to match the SSID, to make it easier to identify
- Wireless tab – Mode AP Bridge
- Wireless tab – SSID make it the same as your last SSID
- Wireless tab – Security profile, choose the appropriate one from the first step above
- Wireless tab – I also modified Band, Channel Width and Frequency (everything else was left at defaults)
- (Repeat as needed for the second interface)
- Enable both when done
- At this point, devices will connect – but will not have internet access
- Bridge – create new bridge (lanBridge)
- Bridge – Ports tab add the two wireless interfaces and ether1 and choose lanBridge
- IP – DHCP Client – I chose the lanBridge as my interface and checked peer dns and ntp
All done, back up the configuration:
Method 1
To do it in a nice easy to read script, use terminal and just run: /export file=config
Then go to Files, right click and download the file to your desktop and open with a text editor
Method 2
To make a backup that your device can restore from, go to Files and choose Backup.
Then right click the new file and download to your desktop.
Future plans:
Replace the tomato router with a hex GR3 router.
Implement the fancy guest wireless network isolated on its own vlan.
Script generated by my setup.
Pretty similar to InstrusDave setup listed above.Code: Select all# mar/24/2018 06:55:33 by RouterOS 6.36.4 # software id = FKCU-VBGC # /interface bridge add name=lanBridge /interface wireless security-profiles add authentication-types=wpa2-psk eap-methods="" management-protection=\ allowed mode=dynamic-keys name=WirelessAP24 supplicant-identity="" \ wpa2-pre-shared-key=This_is_my_password_treat_it_well!!! add authentication-types=wpa2-psk eap-methods="" management-protection=\ allowed mode=dynamic-keys name=WirelessAP50 supplicant-identity="" \ wpa2-pre-shared-key="This is my password treat it well!!!" /interface wireless set [ find default-name=wlan1 ] band=2ghz-onlyn channel-width=20/40mhz-Ce \ disabled=no mode=ap-bridge name=WirelessAP24 security-profile=WirelessAP24 ssid=\ WirelessAP24 set [ find default-name=wlan2 ] band=5ghz-a/n/ac channel-width=\ 20/40/80mhz-eeCe disabled=no frequency=auto mode=ap-bridge name=WirelessAP50 \ security-profile=WirelessAP50 ssid=WirelessAP50 /interface bridge port add bridge=lanBridge interface=ether1 add bridge=lanBridge interface=WirelessAP24 add bridge=lanBridge interface=WirelessAP50 /ip dhcp-client add default-route-distance=0 dhcp-options=hostname,clientid disabled=no \ interface=lanBridge /system clock set time-zone-name=America/New_York /system routerboard settings set cpu-frequency=720MHz protected-routerboot=disabled