Hi, I found this thread very useful on configuring CAPsMAN, but still got no supported channel on 5GHz and I don't understand why. any help is much appreciated.
CapsMAN config
# dec/27/2022 19:13:18 by RouterOS 6.49.2
# software id = PI2D-6Q1P
#
# model = RouterBOARD 941-2nD
# serial number = 5B320271D319
/caps-man channel
add band=2ghz-g/n control-channel-width=20mhz extension-channel=disabled \
frequency=2437,2462 name=channel2.4 skip-dfs-channels=yes
add band=5ghz-onlyac control-channel-width=20mhz extension-channel=disabled \
frequency=5180,5200,5220,5240 name=channel5 skip-dfs-channels=yes
/interface bridge
add admin-mac=D4:CA:6D:F3:43:20 auto-mac=no fast-forward=no name=bridge-local
/interface ethernet
set [ find default-name=ether1 ] advertise=\
10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full name=\
ether1-gateway
set [ find default-name=ether2 ] advertise=\
10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full name=\
ether2-master-local
set [ find default-name=ether3 ] advertise=\
10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full name=\
ether3-slave-local
set [ find default-name=ether4 ] advertise=\
10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full name=\
ether4-slave-local
/interface wireless
set [ find default-name=wlan1 ] band=2ghz-b/g/n channel-width=20/40mhz-Ce \
country=italy distance=indoors frequency=auto mode=ap-bridge ssid=\
MikroTik wireless-protocol=802.11
/caps-man datapath
add bridge=bridge-local local-forwarding=no name=datapath1
/caps-man security
add authentication-types=wpa2-psk encryption=aes-ccm group-encryption=aes-ccm \
name=security1 passphrase=XXXXXXXXXXXX
/caps-man configuration
add channel=channel2.4 country=italy datapath=datapath1 installation=indoor \
name=cfg2.4 security=security1 security.authentication-types=wpa2-psk \
ssid=FF_home
add channel=channel5 country=italy datapath=datapath1 installation=indoor \
name=cfg5 security=security1 security.authentication-types=wpa2-psk ssid=\
FF_home5
/interface list
add exclude=dynamic name=discover
add name=mactel
add name=mac-winbox
/interface wireless security-profiles
set [ find default=yes ] authentication-types=wpa2-psk eap-methods="" mode=\
dynamic-keys supplicant-identity=MikroTik wpa-pre-shared-key=\
XXXXXXXXXXXX wpa2-pre-shared-key=XXXXXXXXXXXX
/ip ipsec proposal
set [ find default=yes ] enc-algorithms=aes-128-cbc
/ip pool
add name=dhcp ranges=192.168.1.150-192.168.1.195
/ip dhcp-server
add address-pool=dhcp authoritative=after-2sec-delay disabled=no interface=\
bridge-local name=default
/snmp community
set [ find default=yes ] addresses=0.0.0.0/0
/caps-man manager
set enabled=yes
/caps-man manager interface
set [ find default=yes ] forbid=yes
add disabled=no interface=bridge-local
/caps-man provisioning
add action=create-dynamic-enabled master-configuration=cfg2.4 name-prefix=FF2
add action=create-dynamic-enabled master-configuration=cfg5 name-prefix=FF5
/interface bridge port
add bridge=bridge-local interface=ether2-master-local
add bridge=bridge-local interface=wlan1
add bridge=bridge-local interface=ether3-slave-local
add bridge=bridge-local interface=ether4-slave-local
/interface bridge settings
set use-ip-firewall=yes
/ip neighbor discovery-settings
set discover-interface-list=discover
/interface list member
add interface=ether2-master-local list=discover
add interface=ether3-slave-local list=discover
add interface=ether4-slave-local list=discover
add interface=wlan1 list=discover
add interface=bridge-local list=discover
add interface=ether2-master-local list=mactel
add interface=wlan1 list=mactel
add interface=ether2-master-local list=mac-winbox
add interface=wlan1 list=mac-winbox
/ip address
add address=192.168.1.1/24 comment="default configuration" interface=\
ether2-master-local network=192.168.1.0
add address=192.168.88.2/24 interface=ether1-gateway network=192.168.88.0
/ip cloud
set update-time=no
/ip dhcp-client
add comment="default configuration" interface=ether1-gateway
/ip dhcp-server lease
add address=192.168.1.91 comment="shinelan Alberto" mac-address=\
00:47:B0:3F:5F:CE server=default
add address=192.168.1.92 comment="shinelan Andrea" mac-address=\
00:47:50:1B:CC:93 server=default
add address=192.168.1.94 comment="RS485 to ETH Andrea" mac-address=\
D4:AD:20:48:1D:7A server=default
/ip dhcp-server network
add address=192.168.1.0/24 comment="default configuration" gateway=\
192.168.1.1 netmask=24
/ip dns
set allow-remote-requests=yes servers=8.8.8.8,8.8.4.4
/ip dns static
add address=192.168.88.1 name=router
/ip route
add distance=1 gateway=192.168.88.1
/ip service
set telnet disabled=yes
set www disabled=yes
set ssh port=2201
/ip upnp
set enabled=yes
/ip upnp interfaces
add interface=bridge-local type=internal
add interface=ether1-gateway type=external
/system clock
set time-zone-autodetect=no time-zone-name=Europe/Rome
/system identity
set name="CapsMan Router"
/system ntp client
set enabled=yes server-dns-names=pool.ntp.org
/tool e-mail
set address=192.168.1.3 from=gw-home@elamb.it
/tool mac-server
set allowed-interface-list=mactel
/tool mac-server mac-winbox
set allowed-interface-list=mac-winbox
CAP config:
# dec/27/2022 19:13:48 by RouterOS 6.49.7
# software id = SLFT-C3D8
#
# model = RBwAPG-5HacT2HnD
# serial number = BED60B7D30DE
/interface bridge
add name=bridge1
/interface wireless
# managed by CAPsMAN
# channel: 2437/20/gn(18dBm), SSID: FF_home, CAPsMAN forwarding
set [ find default-name=wlan1 ] band=2ghz-g/n country=italy frequency=2432 \
installation=indoor mode=ap-bridge name=wlan2.4 ssid=FF_home
# managed by CAPsMAN
set [ find default-name=wlan2 ] band=5ghz-onlyac country=italy frequency=5200 \
mode=ap-bridge name=wlan5 ssid=FF_home_pt5 wps-mode=disabled
/interface wireless security-profiles
set [ find default=yes ] authentication-types=wpa2-psk eap-methods="" mode=\
dynamic-keys supplicant-identity=MikroTik wpa2-pre-shared-key=\
XXXXXXXXXXXX
/interface bridge port
add bridge=bridge1 interface=all multicast-router=disabled
/interface wireless cap
#
set bridge=bridge1 discovery-interfaces=bridge1 enabled=yes interfaces=\
wlan2.4,wlan5
/ip address
add address=192.168.1.24/24 interface=bridge1 network=192.168.1.0
/ip dhcp-client
add disabled=no interface=bridge1
/ip dhcp-relay
add dhcp-server=192.168.1.1 disabled=no interface=bridge1 name=relay1
/system clock
set time-zone-name=Europe/Rome
/system identity
set name="AP tel"
2.4GHz config is applied but network is not visible. I'm using only channel 6 as neighbor has strong wifi on 1 and 11
5GHz still has no supported channel
Thank you
UPDATE: kept working on this. if under provisioning I explicitly put "hardware support mode" as "gn" for 2.4 network and "ac" for 5GHz net, "no supported channel" error disappear and both network are visible to clients. only odd thing: if setup applied by CAPsMAN, shelly devices of home automation will not be able to connect to internet, while if applied directly on AP they work fine without any other config changes
# dec/27/2022 22:19:10 by RouterOS 6.49.7
# software id = SLFT-C3D8
#
# model = RBwAPG-5HacT2HnD
# serial number = BED60B7D30DE
/interface bridge
add name=bridge1
/interface wireless
set [ find default-name=wlan1 ] band=2ghz-g/n country=italy disabled=no \
frequency=2432 installation=indoor mode=ap-bridge name=wlan2.4 ssid=\
FF_home wps-mode=disabled
set [ find default-name=wlan2 ] band=5ghz-onlyac country=italy frequency=5200 \
mode=ap-bridge name=wlan5 ssid=FF_home_pt5 wps-mode=disabled
/interface wireless security-profiles
set [ find default=yes ] authentication-types=wpa2-psk eap-methods="" mode=\
dynamic-keys supplicant-identity=MikroTik wpa2-pre-shared-key=\
XXXXXXXXXXXX
/interface bridge port
add bridge=bridge1 interface=all multicast-router=disabled
/interface wireless cap
set bridge=bridge1 discovery-interfaces=bridge1 interfaces=wlan2.4,wlan5
/ip address
add address=192.168.1.24/24 interface=bridge1 network=192.168.1.0
/ip dhcp-client
add disabled=no interface=bridge1
/ip dhcp-relay
add dhcp-server=192.168.1.1 disabled=no interface=bridge1 name=relay1
/system clock
set time-zone-name=Europe/Rome
/system identity
set name="AP tel"