I have two cAP ac's on both levels around my house.
Decided to turn off wifi during the night with simple script/schedule which works brilliantly.
Problem is that sometimes it takes 20+ minutes for wlan2 to go from S to RS state when script enables interface. Clients can connect only when it's in RS state.
What could be the issue ?
One unit is 3+years old one of first one's with 256g of ram (RouterBOARD cAP Gi-5acD2nD)
Other one is just recently bought with 128g of ram (RBcAPGi-5acD2nD r2)
Every day it's different. Sometime it takes 3min for one, sometimes 23min.
Running 6.48.4
level 1 AP:
Code: Select all
set [ find default-name=wlan2 ] adaptive-noise-immunity=none allow-sharedkey=no ampdu-priorities=0 amsdu-limit=8192 amsdu-threshold=8192 antenna-gain=0 area="" arp=enabled arp-timeout=auto band=5ghz-onlyac basic-rates-a/g=12Mbps bridge-mode=enabled channel-width=20/40mhz-Ce \
compression=no country="new zealand" default-ap-tx-limit=0 default-authentication=yes default-client-tx-limit=0 default-forwarding=yes disable-running-check=no disabled=no disconnect-timeout=3s distance=indoors frame-lifetime=0 frequency=5180 frequency-mode=regulatory-domain \
frequency-offset=0 guard-interval=any hide-ssid=no ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7 ht-supported-mcs=\
mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9,mcs-10,mcs-11,mcs-12,mcs-13,mcs-14,mcs-15,mcs-16,mcs-17,mcs-18,mcs-19,mcs-20,mcs-21,mcs-22,mcs-23 hw-fragmentation-threshold=disabled hw-protection-mode=none hw-protection-threshold=0 hw-retries=7 installation=indoor \
interworking-profile=disabled keepalive-frames=enabled l2mtu=1600 mac-address=2C:C8:1B:15:5A:E7 max-station-count=2007 mode=ap-bridge mtu=1500 multicast-buffering=enabled multicast-helper=default name=wlan2 nv2-cell-radius=30 nv2-downlink-ratio=50 nv2-mode=dynamic-downlink \
nv2-preshared-key="" nv2-qos=default nv2-queue-count=2 nv2-security=disabled nv2-sync-secret="" on-fail-retry-time=100ms preamble-mode=both radio-name=2CC81B155AE7 rate-selection=advanced rate-set=configured rx-chains=0,1 scan-list=default secondary-channel="" \
security-profile=default skip-dfs-channels=all ssid=w station-bridge-clone-mac=00:00:00:00:00:00 station-roaming=disabled supported-rates-a/g=12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps tdma-period-size=2 tx-chains=0,1 tx-power-mode=default update-stats-interval=disabled \
vht-basic-mcs=mcs0-7 vht-supported-mcs=mcs0-9,mcs0-9,mcs0-9 vlan-id=1 vlan-mode=no-tag wds-cost-range=50-150 wds-default-bridge=none wds-default-cost=100 wds-ignore-ssid=no wds-mode=disabled wireless-protocol=802.11 wmm-support=disabled wps-mode=disabled
leve 2 AP:
Code: Select all
set [ find default-name=wlan2 ] adaptive-noise-immunity=none allow-sharedkey=no ampdu-priorities=0 amsdu-limit=8192 amsdu-threshold=8192 antenna-gain=0 area="" arp=enabled arp-timeout=auto band=5ghz-onlyac basic-rates-a/g=12Mbps bridge-mode=enabled channel-width=20/40mhz-eC \
compression=no country="new zealand" default-ap-tx-limit=0 default-authentication=yes default-client-tx-limit=0 default-forwarding=yes disable-running-check=no disabled=no disconnect-timeout=3s distance=indoors frame-lifetime=0 frequency=5240 frequency-mode=regulatory-domain \
frequency-offset=0 guard-interval=any hide-ssid=no ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7 ht-supported-mcs=\
mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9,mcs-10,mcs-11,mcs-12,mcs-13,mcs-14,mcs-15,mcs-16,mcs-17,mcs-18,mcs-19,mcs-20,mcs-21,mcs-22,mcs-23 hw-fragmentation-threshold=disabled hw-protection-mode=none hw-protection-threshold=0 hw-retries=7 installation=indoor \
interworking-profile=disabled keepalive-frames=enabled l2mtu=1600 mac-address=64:D1:54:FF:D7:98 max-station-count=2007 mode=ap-bridge mtu=1500 multicast-buffering=enabled multicast-helper=default name=wlan2 nv2-cell-radius=30 nv2-downlink-ratio=50 nv2-mode=dynamic-downlink \
nv2-preshared-key="" nv2-qos=default nv2-queue-count=2 nv2-security=disabled nv2-sync-secret="" on-fail-retry-time=100ms preamble-mode=both radio-name=64D154FFD798 rate-selection=advanced rate-set=configured rx-chains=0,1 scan-list=default secondary-channel="" \
security-profile=default skip-dfs-channels=all ssid=w station-bridge-clone-mac=00:00:00:00:00:00 station-roaming=enabled supported-rates-a/g=12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps tdma-period-size=2 tx-chains=0,1 tx-power-mode=default update-stats-interval=disabled \
vht-basic-mcs=mcs0-7 vht-supported-mcs=mcs0-9,mcs0-9,mcs0-9 vlan-id=1 vlan-mode=no-tag wds-cost-range=50-150 wds-default-bridge=none wds-default-cost=100 wds-ignore-ssid=no wds-mode=disabled wireless-protocol=802.11 wmm-support=disabled wps-mode=disabled
Thanks,
Artis