Just got myself a CubeG-5ac60adpair that won't connect to eachother straight out of the box as expected.
The setup I'm looking to achieve is as follows; Main router (WRT 32X)<---->Cube1 ))))))(((((( Cube2 <----->Zyxel switch connected to some IP-cameras. No obstacles in the path of wireless transmission (about 5 meters away from each other as of now for troubleshooting).
If I understand this right I should be able to see my IP cameras as if they were connected straight to my main router, which I'm not.
The only thing I've tried so far is to switch which cube is connected to the main router since there are no clear way to tell which one is supposed to. The only difference between the two cubes is that one has a sticker on the side with username and password on it. No other changes or configuration has been made, since the manual says "configuration is optional".
I've managed to connect to each cube by connecting them separately (not at the same time) to my main router and using winbox and each cubes mac-address.
This is the config on each cube:
Cube 1 - password protected login
Code: Select all
[admin@MikroTik] > export
# jan/02/1970 00:01:19 by RouterOS 6.47.10
# software id = 8LWK-U6S3
#
# model = CubeG-5ac60ad
# serial number = E2A30DE7D11D
/interface bridge
add admin-mac=08:55:31:C8:54:FA auto-mac=no comment=defconf name=bridge
/interface wireless
set [ find default-name=wlan1 ] band=5ghz-a/n/ac channel-width=20/40/80mhz-XXXX disabled=no frequency=auto installation=outdoor mode=bridge ssid=MikroTik-c854fa
/interface w60g
set [ find ] disabled=no mode=bridge name=wlan60-1 password=XXXX-XXXX ssid=MikroTik-c854fa
/interface w60g station
add comment=defconf mac-address=08:55:31:C8:54:FB name=wlan60-station-1 parent=wlan60-1 remote-address=08:55:31:C8:55:9D
/interface bonding
add comment=defconf mode=active-backup name=bond1 primary=wlan60-station-1 slaves=wlan60-station-1,wlan1
/interface wireless security-profiles
set [ find default=yes ] authentication-types=wpa2-psk comment=defconf disable-pmkid=yes mode=dynamic-keys supplicant-identity=MikroTik wpa2-pre-shared-key=5fa1-563e
/interface bridge port
add bridge=bridge comment=defconf interface=ether1
add bridge=bridge comment=defconf interface=bond1
/ip address
add address=192.168.88.2/24 comment=defconf interface=bridge network=192.168.88.0
Cube 2 - no password protected login
Code: Select all
[admin@MikroTik] > /export
# jan/02/1970 00:08:41 by RouterOS 6.48.4
# software id = WAPC-Z5P3
#
# model = CubeG-5ac60ad
# serial number = E29D0E463646
/interface bridge
add admin-mac=2C:C8:1B:43:05:DE auto-mac=no comment=defconf name=bridge
/interface wireless
set [ find default-name=wlan1 ] band=5ghz-a/n/ac channel-width=20/40/80mhz-XXXX disabled=no frequency=auto installation=outdoor mode=station-bridge ssid=MikroTik
/interface w60g
set [ find ] disabled=no mode=station-bridge name=wlan60-1 ssid=MikroTik
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/interface bridge port
add bridge=bridge comment=defconf interface=ether1
add bridge=bridge comment=defconf interface=wlan60-1
/ip address
add address=192.168.88.1/24 comment=defconf interface=bridge network=192.168.88.0
My main router has no special configurations, also tried with different router but same result.
Really hope you guys can help me out, thannks in advance!