Community discussions

MikroTik App
 
User avatar
sub_zero
just joined
Topic Author
Posts: 9
Joined: Mon Nov 05, 2007 12:07 pm

Problem With Nstreme Dual

Mon Nov 05, 2007 12:11 pm

Hello,
We have this kind of problem...
Connection Nstreme Dual, 2x PIV 3.2GHz, ver. MT 2.9.34 a 2.9.40, CM9 in individual reductions, 27dBi
spaced parabolic antennas - 3km, Fresnel zone ideal, frequence distance of Tx/Rx channel 300MHz.
Signal -60/-61dBi, cabels checked as well as pigtails and connectors.

There is lovely 34Mbit on RX with 6ms latency (in real tests), but TX has upload from 5 to 22Mbit with 20-150ms latency.
I was looking for a solution through the whole web, I found some similar problems, but nobody solved it ...
Please, do you have any suggestion?

Best regards
 
uldis
MikroTik Support
MikroTik Support
Posts: 3446
Joined: Mon May 31, 2004 2:55 pm

Re: Problem With Nstreme Dual

Mon Nov 05, 2007 1:50 pm

what is your nstreme dual configuration: framer-policy, size.
 
User avatar
sub_zero
just joined
Topic Author
Posts: 9
Joined: Mon Nov 05, 2007 12:07 pm

Re: Problem With Nstreme Dual

Mon Nov 05, 2007 4:00 pm

yes...framer polici is framer size and the limit is 4000..
 
jober
Long time Member
Long time Member
Posts: 690
Joined: Fri May 28, 2004 12:16 pm
Location: Louisiana,USA

Re: Problem With Nstreme Dual

Mon Nov 05, 2007 5:13 pm

I don't use 2.4Ghz in the big easy for APs, so I used one of the 2.4 channels for one of the links on the dual nstreme ptp and it stop any interference in the nstreme box. The 5.8 and 2.4 panel antennas are stacked on top of each other. The link works great! :D
Maybe you could try it.
 
User avatar
sub_zero
just joined
Topic Author
Posts: 9
Joined: Mon Nov 05, 2007 12:07 pm

Re: Problem With Nstreme Dual

Mon Nov 05, 2007 5:25 pm

I don't use 2.4Ghz in the big easy for APs, so I used one of the 2.4 channels for one of the links on the dual nstreme ptp and it stop any interference in the nstreme box. The 5.8 and 2.4 panel antennas are stacked on top of each other. The link works great! :D
Maybe you could try it.
impossible. Here is very big activity on 2.4Ghz band. We must operation only 5Ghz band. I read somewhere, that this problem makes some version of MT, that this problem will be fix, on version 3.0..
 
jober
Long time Member
Long time Member
Posts: 690
Joined: Fri May 28, 2004 12:16 pm
Location: Louisiana,USA

Re: Problem With Nstreme Dual

Mon Nov 05, 2007 6:24 pm

How will an OS software change fix a RF interference problem? :?
 
User avatar
sub_zero
just joined
Topic Author
Posts: 9
Joined: Mon Nov 05, 2007 12:07 pm

Re: Problem With Nstreme Dual

Mon Nov 05, 2007 7:48 pm

How will an OS software change fix a RF interference problem? :?
and my problem is just RF interference? can here anybody posted any functionaly config Nstreme Dual on 5Ghz?

my config is here:

One Site
name="wlan1" mtu=1500 mac-address=00:0B:6B:56:FB:33 arp=enabled 
      disable-running-check=no interface-type=Atheros AR5213 
      radio-name="p2p_zero" mode=nstreme-dual-slave ssid="nstreme1" area="" 
      frequency-mode=manual-txpower country=czech republic antenna-gain=20 
      frequency=5540 band=5ghz scan-list=default rate-set=default 
      supported-rates-b="" supported-rates-a/g=54Mbps basic-rates-b="" 
      basic-rates-a/g=54Mbps max-station-count=2007 ack-timeout=dynamic 
      tx-power-mode=default noise-floor-threshold=default 
      periodic-calibration=default periodic-calibration-interval=60 
      burst-time=disabled dfs-mode=none antenna-mode=ant-a wds-mode=disabled 
      wds-default-bridge=none wds-default-cost=100 wds-cost-range=50-150 
      wds-ignore-ssid=no update-stats-interval=disabled 
      default-authentication=no default-forwarding=no default-ap-tx-limit=0 
      default-client-tx-limit=0 proprietary-extensions=pre-2.9.25 
      hide-ssid=no security-profile=default disconnect-timeout=3s 
      on-fail-retry-time=100ms preamble-mode=long compression=no 
      allow-sharedkey=no 
 name="wlan2" mtu=1500 mac-address=00:0B:6B:56:FB:C4 arp=enabled 
      disable-running-check=no interface-type=Atheros AR5213 
      radio-name="000B6B56FBC4" mode=nstreme-dual-slave ssid="nstreme2" 
      area="" frequency-mode=manual-txpower country=czech republic 
      antenna-gain=10 frequency=5580 band=5ghz scan-list=default 
      rate-set=default supported-rates-b="" supported-rates-a/g=6Mbps 
      basic-rates-b="" basic-rates-a/g=6Mbps max-station-count=20 
      ack-timeout=dynamic tx-power-mode=default noise-floor-threshold=default 
      periodic-calibration=default periodic-calibration-interval=60 
      burst-time=disabled dfs-mode=none antenna-mode=ant-a wds-mode=disabled 
      wds-default-bridge=none wds-default-cost=100 wds-cost-range=50-150 
      wds-ignore-ssid=no update-stats-interval=disabled 
      default-authentication=no default-forwarding=no default-ap-tx-limit=0 
      default-client-tx-limit=0 proprietary-extensions=pre-2.9.25 
      hide-ssid=no security-profile=default disconnect-timeout=3s 
      on-fail-retry-time=100ms preamble-mode=long compression=no 
      allow-sharedkey=no 
 R name="nstreme1" mtu=1500 mac-address=00:0B:6B:56:FB:C4 arp=enabled disable-running-check=no tx-radio=wlan1 rx-radio=wlan2 remote-mac=00:0B:6B:81:EC:E9 
      tx-band=5ghz tx-frequency=5540 rx-band=5ghz rx-frequency=5680 rates-b="" rates-a/g=36Mbps framer-policy=exact-size framer-limit=4000
Other site
 name="wlan3" mtu=1500 mac-address=00:0B:6B:81:EC:E9 arp=enabled disable-running-check=no interface-type=Atheros AR5213 radio-name="000B6B81ECE9" 
      mode=nstreme-dual-slave ssid="MikroTik" area="" frequency-mode=manual-txpower country=albania antenna-gain=0 frequency=5180 band=5ghz scan-list=default 
      rate-set=default supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps 
      basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007 ack-timeout=dynamic tx-power-mode=default noise-floor-threshold=default 
      periodic-calibration=default periodic-calibration-interval=60 burst-time=disabled dfs-mode=none antenna-mode=ant-a wds-mode=disabled 
      wds-default-bridge=none wds-default-cost=100 wds-cost-range=50-150 wds-ignore-ssid=no update-stats-interval=disabled default-authentication=yes 
      default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0 proprietary-extensions=post-2.9.25 hide-ssid=no security-profile=default 
      disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=long compression=no allow-sharedkey=no 
name="wlan5" mtu=1500 mac-address=00:0B:6B:37:6A:29 arp=enabled disable-running-check=no interface-type=Atheros AR5213 radio-name="000B6B376A29" 
      mode=nstreme-dual-slave ssid="Mikrotik" area="" frequency-mode=manual-txpower country=czech republic antenna-gain=0 frequency=5180 band=5ghz 
      scan-list=default rate-set=default supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps supported-rates-a/g=48Mbps,54Mbps basic-rates-b="" 
      basic-rates-a/g=48Mbps,54Mbps max-station-count=2007 ack-timeout=dynamic tx-power-mode=defaut tx-power-mode=all-rates-fixed noise-floor-threshold=default 
      periodic-calibration=default periodic-calibration-interval=60 burst-time=disabled dfs-mode=none antenna-mode=ant-a wds-mode=disabled 
      wds-default-bridge=none wds-default-cost=100 wds-cost-range=50-150 wds-ignore-ssid=no update-stats-interval=disabled default-authentication=yes 
      default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0 proprietary-extensions=post-2.9.25 hide-ssid=no security-profile=default 
      disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both compression=no allow-sharedkey=no 
 R name="nstreme1" mtu=1500 mac-address=00:0B:6B:81:EC:E9 arp=enabled disable-running-check=no tx-radio=wlan5 rx-radio=wlan3 remote-mac=00:0B:6B:56:FB:C4 
      tx-band=5ghz tx-frequency=5680 rx-band=5ghz rx-frequency=5540 rates-b="" rates-a/g=54Mbps framer-policy=exact-size framer-limit=4000
 
tully
MikroTik Support
MikroTik Support
Posts: 502
Joined: Fri May 28, 2004 11:07 am

Re: Problem With Nstreme Dual

Tue Nov 06, 2007 11:54 am

The supported rates are screwed up. You should probably do a system reset and start over.

Who is online

Users browsing this forum: No registered users and 51 guests