MikroTik

Posted: **Fri Apr 14, 2006 3:20 pm**

We are planning to equip our new cpes with routerboards. Is there a possibility to allow the customer to allign the antenna without giving him access to the whole router? Maybe with an integrated webserver or with a client application via snmp?

Or do I have to write my own application?

Posted: **Fri Apr 14, 2006 9:50 pm**

Let me dig in the office on Tuesday. I think I have something like this flying around my hard disk...

If I just forget to come back here, a short reminder to info at cmit dot de might help

Best regards,
Christian Meis

Posted: **Fri Apr 14, 2006 10:15 pm**

Thanx!

Und: Schöne Ostern!

Posted: **Sat Apr 15, 2006 3:33 pm**

hi cmit,

if you would be so kind to mail it to me too !

thanks in advance

arco

Posted: **Sat Apr 15, 2006 6:39 pm**

Cmit, here too, please?

Mike

Posted: **Sun Apr 16, 2006 8:58 am**

Me too please.

Posted: **Sun Apr 16, 2006 2:35 pm**

HI All.

We have made a custom Apps that are pretty cool

that uses both SNMP and Telnet. And we are showing the Signal with a grapich bar red,yellow,green for the signal strenght.
and you can set the SSID for diffrent base stations...
and soon we can let the Customers Scan and then connect.
and the apps is in the MT routerboard disk....
so we dont need any cd roms. And we uppdate the apps via ftp

if some one is intrested mail me on rickard@rbcom.se

Posted: **Tue Apr 18, 2006 12:50 pm**

Ok, found it

Short list of features:
Small client app to help clients/customers to align their (RouterOS based) CPE. (The CPE is queried by SNMP.)
The customer just enters the ip address of the CPE and presses "Start".

The app is showing you:
- system name
- MAC (wlan) of you CPE
- configured frequency
- wireless connection status (via a red/green signal)
- wireless signal strength (numeric dB and bar graph)

It's in last beta state, so I have to finish some things to get things running. Of course it's one single exe file, no installation, no registry trash, ...

I will offer that as a branded app to interested WISPs. Anyone interested please write me a short email to info at cmit dot de to get in touch.

Best regards,
Christian Meis

Posted: **Tue Apr 18, 2006 2:05 pm**

/me queue up

aviper (at) mail (dot) bg

Posted: **Tue Apr 18, 2006 4:19 pm**

The RB112's have a built in speaker/beeper. From my understanding this is to allow alaignment via a tone. I have not tried it so I do not know if it is functioning is in the software yet or not. But if/when this works it is a perfect tool for most self installs.

We also use the WaveRider product and one nice feature is the units are always available through the 169.254.10.250 ip address regardless of what the managment address has been configured for. You may recognize this as a block that windows will give an interface by default if it can not come up with a DHCP address. Has anyone used or considered using this block so any end user software could be set to communicate to the radio with out the user haveing to configure an IP address? Could be a fast and simple way to get novice end users to connect up to a radio and enter in information in cases where the AP has to be chosen. Or other location dependant information is required. I'm no programer so I can only help with the idea!

Erik

Posted: **Wed Apr 19, 2006 7:09 pm**

So, who do i need to kiss to get this too

Also writing one in with delphi. Don't have snmp vcl though.
Everything scripted and parsed through telnet

willing to share code.

Posted: **Wed Apr 19, 2006 9:59 pm**

OK, guys... No need to kiss anyone, actually (or do kiss your wife, if you have one

).

I'm totally burried in the finishing stages of a project and not really in the office for the rest of this week.
I'll get back to everyone here and the ones who e-mailed me next week.
Let me at least get it translated to English - I suppose most of you won't make much use of it with a German user interface...

Best regards,
Christian Meis

Posted: **Sun Apr 30, 2006 12:23 am**

Any news ???

Posted: **Mon May 01, 2006 8:20 pm**

We have "RadioManager", runs on a PC or laptop, connects with Telnet or RS232 port, has easy-to-use RSSI (signal strength) bargraphs, and even audio tones for alignment using the PC sound system/speakers - great for CPEs that don't have any buzzers etc. Can be customised for operator/WISP OEM use.
All parameters can be viewed but password-ony access for "settable" items such as freq, SSID, etc. Allows authorised user to launch bandwidth tests etc. Ideal for corporate and WISP use.

An "old version" screenshot here:
http://www.cablefreesolutions.com/radio ... anager.jpg

Release version just about to be launched, a few days away (software is stable, just the registration portal being production-tested)
Any interest, do email us:
radiosupport (at) cablefreesolutions.com

Best news, it's free...

Regards

CableFree Solutions

Posted: **Tue May 02, 2006 6:38 pm**

So, anyone who has not contacted me via e-mail (Arco, Mike, Nuru, Dibatech?) just drop me a line at info at cmit dot de.

All others should have their eval version in their mailboxes...

Best regards,
Christian Meis

Posted: **Mon Aug 06, 2007 8:38 am**

Chris, would you mind email me those app too? (unlimited_question2004 at yahoo dot com)
thx a lot

Posted: **Mon Aug 06, 2007 12:06 pm**

Just sent

Best regards,
Christian Meis

Posted: **Tue Aug 07, 2007 4:54 pm**

Hi Chris,

Can you send it to me, please?
My email is: sofiamarq@iol.pt

Thanks a lot

Posted: **Tue Aug 07, 2007 6:55 pm**

Hi Chris,
Can you send it to me, please?
My email is: sofiamarq@iol.pt
Thanks a lot

And me please

info[at]levi[dot]ee

Posted: **Tue Aug 07, 2007 7:27 pm**

Hi Chris,
may you send it also to me, please?
My e-mail is: nicolaercole@libero.it

Thanks,
nick52

Posted: **Wed Aug 08, 2007 6:02 pm**

Sent to everyone who requested it until now

Best regards,
Christian Meis

Posted: **Wed Aug 08, 2007 7:57 pm**

I'd like to take a look, cmit. mike [at] akodi.net. Also customs, branding...

TNX

Posted: **Wed Aug 08, 2007 8:41 pm**

Hallo Christian,

Can you send it to me, please?
My email : edit...
Thanks

Posted: **Thu Aug 09, 2007 10:47 am**

Hello,

Can you send it to me?

kamil [at] extendbroadband.com

Thanks

Posted: **Thu Aug 09, 2007 11:27 am**

I'd like to take a look,

kiket01(at)gmail.com

thanks cmit.

Posted: **Thu Aug 09, 2007 10:20 pm**

i would like to take a look also..

jason.king [at] sunbeach dot net

Posted: **Fri Aug 10, 2007 12:01 am**

Hi, can you send for me, Cmit...
My email: fmelogno@hotmail.com
Thanks...

Posted: **Fri Aug 10, 2007 10:54 am**

If you could be so kind, i would like to see it too, Cmit. thx in advance
fanepix at yahoo dot com.

Posted: **Fri Aug 10, 2007 12:10 pm**

hello Cmit
can i test your software?

Posted: **Fri Aug 10, 2007 3:40 pm**

Yes - but I would need your e-mail address to send it to you

Either post here or write to info <at> cmit <dot> de

Best regards,
Christian Meis

Posted: **Sat Aug 11, 2007 1:22 am**

sorry

kamil [at] extendbroadband.com

thanks

Posted: **Sat Aug 11, 2007 8:13 am**

jober [at] skycom1 dot com

Thanks

Posted: **Sat Aug 11, 2007 2:19 pm**

Kindly... Appreciate..

support@gcs.co.za

Thx in advance

Posted: **Sat Aug 11, 2007 2:24 pm**

i would also love to have it cmit

Posted: **Sun Aug 12, 2007 8:31 am**

I would also like a copy at matt <at> velociter <dot> net.

Thanks,
Matt

Posted: **Mon Aug 13, 2007 9:11 am**

likewise, please

service@uberpc.co.nz

Posted: **Fri Aug 17, 2007 4:36 pm**

I'd like to try it out Christian.
TYVM
gberg at cyberpine.net

Posted: **Sat Aug 18, 2007 12:44 pm**

Would be great if you could send it to me too

dexterp37 at gmail.com

Posted: **Sun Aug 19, 2007 7:14 am**

Love to try it.
jgwaldrop at hotmail dot com

Posted: **Sun Aug 19, 2007 8:13 am**

Me too, please. npbrasil <at> gmail (dot) com. Thanks!

Posted: **Sun Aug 19, 2007 8:52 am**

Cmit, me to plz

dianseh[at]sixnezer[dot]com thanks

Posted: **Sun Aug 19, 2007 11:31 am**

cmit, me too please.
My Email: francesco.l at web dot de

Posted: **Mon Aug 20, 2007 7:55 pm**

Hi ,

I would like to try the application also , please send it to francisvictor@seychelles.sc

Thanks

Francis

Posted: **Tue Aug 21, 2007 9:14 am**

me too: speedweb1@googlemail.com

Posted: **Tue Aug 21, 2007 2:32 pm**

Me too please.
emiliano<at>cablenet<dot>com<dot>ar

tnx

Posted: **Fri Aug 24, 2007 10:13 am**

Cmit,

can I hav a try too plz - matdawam [at] gmail [dot] com

thx

Posted: **Fri Aug 24, 2007 9:57 pm**

me too: asterix_spawn@hotmail.com

Posted: **Mon Aug 27, 2007 3:10 pm**

Me too please :
robert_lipinski@derkom.pl
THX

Posted: **Mon Aug 27, 2007 8:55 pm**

um, rapidshare?

Posted: **Mon Aug 27, 2007 10:11 pm**

may i have this to
bigbrother@webmail.co.za

Posted: **Wed Aug 29, 2007 9:36 am**

Hallo Christian,

Can you send it to me, please?
My email : rauulu [at] gmail [dot] com

Thanks!

Posted: **Wed Aug 29, 2007 5:13 pm**

could I please have it as well? Ken@surfnetc dot com

Posted: **Thu Aug 30, 2007 3:26 am**

Could I please recieve the application?

dallas @ linuxsrv.net
Dallas

Posted: **Thu Aug 30, 2007 3:30 am**

me too "Please"

Thanks!
mwi (at) moorelandisp (dot) net

Posted: **Thu Aug 30, 2007 10:02 am**

Hy Christian, i already sent you an email, but never got an answer...

Can you send me the app? mip at cpuzone dot it

Posted: **Thu Aug 30, 2007 10:13 am**

also got no answer till now

Possible to post a download link?

Posted: **Thu Aug 30, 2007 9:32 pm**

Hi, Cris

you sent to me : sandro@tganet.com.br

Posted: **Fri Aug 31, 2007 8:17 pm**

Cmit, please send a copy, thanks for all you do.

steve at vroomwireless dot com

Posted: **Sat Sep 01, 2007 9:22 am**

Yes - but I would need your e-mail address to send it to you

Either post here or write to info <at> cmit <dot> de

Best regards,
Christian Meis

abuse[at]chirpan[dot]com

thanks,
C. G.

Posted: **Sat Sep 01, 2007 1:57 pm**

How I wanted to have some programming skills to do an app like that.
Could you send me a copy: " danielillu [at] hotmail dot com "

Many thanks!

Posted: **Sun Sep 02, 2007 3:34 am**

me too Please Thanks!
kadhemaaa(at) yahoo (dot) com

Posted: **Sun Sep 02, 2007 7:55 pm**

I would like this too!

andreas[at]silowireless.com

Posted: **Sun Sep 02, 2007 8:59 pm**

Looks like a great app.

Me too please!

ghmorris (at) candlelight.ca

Thanks
George

Posted: **Mon Sep 03, 2007 3:58 pm**

Me too, please. ofasa {at} yahoo {dot} com.

Thanks.

Posted: **Mon Sep 03, 2007 8:10 pm**

may I try the software too please
antenna.mr (at) gmail (dot) com

Posted: **Wed Sep 05, 2007 7:32 pm**

me too please
andrisoripada at gmail dot com

Posted: **Thu Sep 06, 2007 1:25 am**

I found this site that hosts the Radio Manager software.

http://www.cablefreecommunications.com/

I really like the app. except it really needs the ability to check RSSI via SNMP.
I wouldn't want to give out any telnet passwords to our customers.

Posted: **Thu Sep 06, 2007 1:33 am**

Thanls springwifi, but the download link you provided doesn't work, now. Maybe is a temporal error

Posted: **Thu Sep 06, 2007 5:09 am**

Found the correct link!

http://cablefreesolutions.com/software/ ... ger3v2.exe

Posted: **Thu Sep 06, 2007 10:11 am**

Both links should be correct - one leads to the other.
Just for clarity, that's CableFree's Radiomanager software, which is a Windows GUI, works with most versions of ROS, is frequently updated (with auto version update prompt) and lets you see most aspects of a radio configuration - ideal for P2P links as well as base stations and CPEs.

The software was written to run with our own-brand hardware, but will run with any MT/ROS box.
You do need to put a custom script on your radio to use it - adds a unique user/password for the software to log on.
Drop me a mail at stephen <dot> patrick [at] cablefree <dot> co <dot> uk and we'll send it over.

We welcome feedback for any features users would like to see in our software.

Regards

CableFree Solutions

Posted: **Fri Sep 07, 2007 8:59 am**

Please sent to support at eburg dot com

Thank you

Posted: **Sat Sep 08, 2007 5:29 pm**

Whats a user and password necessary for connect using a Radio Manager, i dont connect in my Wireless Radios, dont have acess !!!

Sandro

Posted: **Mon Sep 10, 2007 10:50 am**

Dear Sandro,
Do drop us an email, we'll send you the script.
It's requested not to put it on a public forum, because of the obvious security risk.

Best regards

CableFree Solutions

Posted: **Wed Sep 12, 2007 7:09 pm**

OK, everybody who hasn't gotten the eval version in his e-mail box until now - I have resent it to those, as there seems to have been some problem with that mail not reaching several people.
If you requested it and still don't have it in your inbox until in about 10 minutes, please send a short notification to me by email - thanks!

Best regards,
Christian Meis

Posted: **Sat Sep 15, 2007 2:47 am**

Cmit; Thanks..
And if you can make it as Orinoco software, I'll be happy to bye it.

Thaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaanks

Posted: **Tue Sep 18, 2007 11:48 pm**

I downloaded it from the link above and I am getting Run-time error '429': ActiveX component can't create object. My email is lljr@1starnet.com if there is a different install file I need.

Thank you!

Posted: **Wed Sep 19, 2007 6:02 am**

Me too pretty please.

znuffy@gmail.com

Gmail doesn't accept .exe's, or zipped .exe's, so you should mail it as a rar or something

Thanks

Posted: **Sat Sep 22, 2007 2:44 am**

Any chance of a symbian version ? I do this atm : http://wiki.mikrotik.com/wiki/CPE_alignment_method

Posted: **Fri Sep 28, 2007 3:43 pm**

Hey Christian,
Always appreciate reading your comments on the forums.
I would like to test your app.
rodneal at htwc dot biz

Thank you,
Rod

Posted: **Sun Sep 30, 2007 7:10 am**

Thanks in advance

telstar924 at yahoo dot com

Posted: **Mon Oct 01, 2007 3:12 am**

Hi
Also want to try it too. Many thank's

email: mikrotik at mls dot nc

Posted: **Mon Oct 01, 2007 7:20 am**

Hi Chris, Canadian WISP here, would liek to give her a go also pls.

admin (at) pogosansfil (dot) net

Vielen Dank

Posted: **Sat Oct 06, 2007 1:06 pm**

hello Christian
can i have your software?

My e-mail is spiller.marco@tiscali.it

thanks

Posted: **Tue Oct 09, 2007 11:20 pm**

hello Christian
can i have your software?

My e-mail is samsoft08@yahoo.com

thanks

Posted: **Sun Oct 14, 2007 6:20 am**

Hi Chris can i have it for a try?
my email is onowojemma[at]yahoo.com
Thanks

Posted: **Wed Oct 17, 2007 12:32 pm**

hello Christian
can i also have your software?
My email is mirazhiukas (at) gmail dot com

thanks a lot

Posted: **Tue Oct 23, 2007 7:19 pm**

Would be great if you could send it to me too,
gun@kirz.com

Posted: **Mon Oct 29, 2007 12:14 am**

I would also like to give it a try.

rob <at> springwifi <dot> com

Posted: **Mon Oct 29, 2007 12:18 am**

Could you send it to me also

kawaki85 (at) yahoo (dot) co (dot) uk

Thanks

Posted: **Mon Oct 29, 2007 5:53 am**

can i also gesseldaniel@yahoo.com

Posted: **Tue Feb 12, 2008 10:29 pm**

Could I also get the script... brandenburg.todd@gmail.com thanks

Posted: **Sat Apr 12, 2008 4:23 pm**

Hello cmit,

If you would be so kind to mail it to me too !

thanks in advance

ihernandez at c-com dot net dot ve or
ignaciohernandezr at gmail dot com

Posted: **Sat May 31, 2008 9:03 pm**

Hello cmit,

If you would be so kind to mail it to me too !

thanks in advance

ebarriosjr at gmail dot com

Posted: **Sat May 31, 2008 10:43 pm**

Hi, mail me to, Cmit...
My email: sandro@tganet.com.br
Thanks...

Posted: **Sun Jun 01, 2008 12:56 am**

G'day Cmit.

If you have any left could you mail me a copy at:

tony@clovabay.net.nz

Vielen Dank.

Posted: **Sun Jun 01, 2008 2:51 pm**

Could you send it to me also
jrecabeitia@talahenen.com.ar

Posted: **Mon Jun 02, 2008 7:03 pm**

sent to me also if you could

rclark@bulleri.net

Posted: **Tue Jun 03, 2008 1:59 pm**

Could you send it to me also

brendanhurley@gmail.com

ta

Posted: **Tue Jun 03, 2008 2:53 pm**

Hello Mikrotik Support,

don´t you see how many people need a tool with which they can monitor the Signal strenghts for installation of a CPE?!

So - why don´t you integrate a signal monitor in ROS where we (or our customers) can see the singal strengths of the wireless interface!
I think integration would be quite simple for you and would give us a real adavantage!

maybe by typing the ip address of the ether if into a webbrowser (like the admin tool works atm).
The admin tool could move to ip-adress/admin or so...

Please be so kind and have a look at this issue.

Posted: **Tue Jun 03, 2008 2:59 pm**

you can use the wireless align mode with the beeper.

Posted: **Tue Jun 03, 2008 5:12 pm**

Hey Cmit, I E-mailed you a while ago but no reply. If you have a chance or Anyone else that has it and can send it to me it would be very much appreciated.

E-mail @ jbwireless4you@gmail.com Thanks. -Jordan

Posted: **Tue Jun 03, 2008 10:30 pm**

you can use the wireless align mode with the beeper.

beeper is not really the right thing if you (or a customer) is installing a CPE!
Or why do you think everybody asks for such a tool?

most competitors have something where you can see the signal strenghts - not only because it is funny...

And i think this is really no work for mikrotik but an advantage for every user...

Posted: **Wed Jun 04, 2008 12:13 am**

you can use the wireless align mode with the beeper.
beeper is not really the right thing if you (or a customer) is installing a CPE!
Or why do you think everybody asks for such a tool?

most competitors have something where you can see the signal strenghts - not only because it is funny...

And i think this is really no work for mikrotik but an advantage for every user...

Mikrotik does have a signal reading go into the registered tab it gives signal strength etc etc. but a nice tool like this may eas install's

Posted: **Wed Jun 04, 2008 8:36 am**

you can use the wireless align mode with the beeper.

Well I just tried /interface wireless align monitor on an RB133C running v3.9 and it immediately rammed the CPU usage to 100% and produced no results for over a minute. Closed the console and the CPU rate remained at 100% for several more minutes before it returned to 'normal'.

Having already had to 'downgrade' several routers from v3.x to 2.9.51 because of problems I'm beginning to suspect that the 'smaller RAM' versions of the 100 series at least just can't cope with v3.

Posted: **Wed Jun 04, 2008 10:06 am**

Mikrotik does have a signal reading go into the registered tab it gives signal strength etc etc. but a nice tool like this may eas install's

yes - but i think thats all too difficult.
We only want to tell our customer: "got to "ip-address" and there you´ll see your signal Strength.
There shoud be a signal value and maybe some graphic wichs shows a "Signal-Graph" with red, yellow and green colours (depending on the signal strenghts)...
So the customer needs no technical know how - he just has to type in an address and could see if the signal is good or not...

Posted: **Wed Jun 04, 2008 10:38 am**

Mikrotik does have a signal reading go into the registered tab it gives signal strength etc etc. but a nice tool like this may eas install's
yes - but i think thats all too difficult.
We only want to tell our customer: "got to "ip-address" and there you´ll see your signal Strength.
There shoud be a signal value and maybe some graphic wichs shows a "Signal-Graph" with red, yellow and green colours (depending on the signal strenghts)...
So the customer needs no technical know how - he just has to type in an address and could see if the signal is good or not...

We've found that it's better to tell the customer to give us a call when he aligns his
antenna. So he needs only a cellphone while he's climbing his roof. With a client
app he has to take his laptop up (if he has one) and has additional cabling, ...
Only alternative would be an led-row at the back of the routenna showing signalstrength.

Stefan

Posted: **Wed Jun 04, 2008 11:18 am**

we have also "non-Mikrotik" CPEs wich show us the signal via web-interface like I wrote before...
And there is nearly no one that cannont handle the installation by himself.

With Mikrotik CPEs we have to use the tool from cmit (which does not work if the wlan if is in a bridge) or have to call/drive to the custumer -> cost´s a lot of time...

Posted: **Sun Jun 22, 2008 7:59 am**

cmit,

If you are still giving out the script to create the special username/password, I'd sure appreciate a copy.

Thanks!

alan@fiebig.us

Posted: **Sun Jun 22, 2008 4:51 pm**

I'm surprised I havn't asked for the software yet, So dear Cmit can you please send me a copy of your software. e-mail: info at vnet-bd dot com.

Many thanks in advance

Posted: **Fri Jul 04, 2008 3:45 am**

cmit, are you still active on this thread, and if so, are you still offering the script? I have downloaded your application, and would like to try it on some of my mikrotik routers, but need the script to do so.

Is that script to create the special username/password for this application available anywhere, from anyone, else?

Thanks!

cmit,

If you are still giving out the script to create the special username/password, I'd sure appreciate a copy.

Thanks!

alan@fiebig.us

Posted: **Fri Jul 04, 2008 12:01 pm**

Ehm, now I'm lost somewhere

...

What script for a "special username/password" do you mean?
The thread here was about an app for CPE alignment...

Posted: **Fri Jul 04, 2008 4:06 pm**

Ehm, now I'm lost somewhere ...

What script for a "special username/password" do you mean?
The thread here was about an app for CPE alignment...

So are you holding onto this Antenna alignment tool? Just lemme know I wount bother you anymore

Posted: **Fri Jul 04, 2008 11:38 pm**

Ehm, now I'm lost somewhere ...

What script for a "special username/password" do you mean?
The thread here was about an app for CPE alignment...

Perhaps there are two different applications being discussed on this thread?

The software was written to run with our own-brand hardware, but will run with any MT/ROS box.
You do need to put a custom script on your radio to use it - adds a unique user/password for the software to log on.

Do drop us an email, we'll send you the script. It's requested not to put it on a public forum, because of the obvious security risk.

cmit, if the above mentioned script is for an application different from yours, could you then please email me a copy of your application to alan@fiebig.us?

Thanks!

Posted: **Tue Jul 15, 2008 12:59 pm**

I would love to evaluate your software aswell..
..but no kisses for you!

renato.bernardi {at} medianetitalia.net

Posted: **Thu Sep 11, 2008 8:08 pm**

hello Christian
can i have your software?

My e-mail is mniche@cox.net

thanks

Kevin

Posted: **Fri Sep 12, 2008 9:57 pm**

Just for completeness/clear up confusion:
"radiomanager" is from our company, CableFree.
You have to put a script on the box to allow the software to connect.
But, the current version doesn't support 3.x, a new version is due soon.

Regards

Posted: **Wed Sep 17, 2008 10:31 am**

hey Cmit can you please send to me that software so i can test it?

mail support@netwave.co.za

Kindly Regards

Posted: **Thu Sep 25, 2008 4:35 pm**

Cmit,
You send to me please?

jeancog84@hotmail.com

Thanks

Posted: **Thu Sep 25, 2008 5:12 pm**

pieter@fxbmining.co.za

Thanks

Posted: **Wed Dec 03, 2008 4:21 pm**

please send it to me also:

amartini6@inwind.it

thank you

Posted: **Thu Dec 04, 2008 11:28 am**

Can I have the script for special username/password please?
Is RadioManager now compatible with ROS 3.x?
guyver30@gmail.com

Posted: **Mon Dec 08, 2008 11:05 am**

Very very useful and intresting...

Can You send to me please?

uomogamma@gmail.com

Thanks so much

M.

Posted: **Tue Dec 09, 2008 8:59 pm**

Witelcom (http://www.witelcom.com) have a software called RAT on their support page - works fine...

Posted: **Wed Dec 10, 2008 9:53 pm**

The Rat software seems to need a password for the zip. I couldn't open it.

Tom

Posted: **Wed Dec 10, 2008 11:46 pm**

Yeah, you're right - I e-mailed their support or info and got a password - I'll see if I can find it.

In the jpg you can see how it looks like. Turns amber and red for lower signal levels. It has big numbers so it's easy to see - even from distance. Seen some limitations though; only station mode and the OID must be right or else it tend to hang...

Posted: **Sun Dec 14, 2008 11:13 pm**

Yeah, you're right - I e-mailed their support or info and got a password - I'll see if I can find it.

In the jpg you can see how it looks like. Turns amber and red for lower signal levels. It has big numbers so it's easy to see - even from distance. Seen some limitations though; only station mode and the OID must be right or else it tend to hang...

Password is public Dogggs

Posted: **Mon Dec 15, 2008 4:50 pm**

Thanks for looking it up, but they must have changed the password.

Tom

Posted: **Mon Dec 15, 2008 6:03 pm**

Thanks for looking it up, but they must have changed the password.

Tom

Got the software today. There was no password. Works fine for me.

Stefan

Posted: **Mon Dec 15, 2008 6:15 pm**

I downloaded it again and also no problem or password this time, thanks.

Tom

Posted: **Mon Dec 15, 2008 6:52 pm**

I didn't catch the part about only working in station mode, that must be why it isn't working for me. I cant find a way to use station mode instead of station-pseudobridge and give a customer a public address without natting.

Tom

Posted: **Mon Dec 15, 2008 6:57 pm**

I didn't catch the part about only working in station mode, that must be why it isn't working for me. I cant find a way to use station mode instead of station-pseudobridge and give a customer a public address without natting.

Tom

asked me for a pass e-mailed them and they said pass is "Public" put it in and it worked.

Posted: **Mon Dec 15, 2008 11:42 pm**

I contacted them the other day - since I could not find the password again, and they said; Oops, no need for password on this - we'll remove it"

The software is made for WISP, and made to i.e. run directly from a CD. It expect you to be connected to a CPE in station mode with NAT and DHCP service. It will grab your PCs default gateway (the CPE then) and use SNMP to poll with the predefined community string. Quite clever and works nice for DIY installations.

You can point it to other IP-addresses also, but the OID must be correct - default for wlan1. I've seen that changing a wlan card messes this up (due to OID counter), and a system reset is required to get it working. Don't know if it works in sudo-bridge - we don't use it. Makes less sense to try on a base station I guess...

Posted: **Tue Dec 16, 2008 9:42 pm**

What do thay meen by "the OID must bee the same"

Posted: **Wed Dec 17, 2008 12:11 am**

I did not say "the OID must be the same", did I?
I said "the OID must be correct - default for wlan1"

Posted: **Wed Dec 17, 2008 5:44 pm**

I did not say "the OID must be the same", did I?
I said "the OID must be correct - default for wlan1"

Wath do you meen by that?

Posted: **Wed Dec 17, 2008 11:25 pm**

I did not say "the OID must be the same", did I?
I said "the OID must be correct - default for wlan1"
Wath do you meen by that?

Well, it's in my post:

"You can point it to other IP-addresses also, but the OID must be correct - default for wlan1. I've seen that changing a wlan card messes this up (due to OID counter), and a system reset is required to get it working"

You will have to try for yourselves here...

Posted: **Tue Dec 23, 2008 8:37 am**

me to please

xezen182x@gmail.com

Posted: **Sat Jan 03, 2009 11:34 pm**

can i have it too? oinioin@yahoo.com,thanks alot

Posted: **Fri Jan 09, 2009 7:50 pm**

There is a new RAT1.6 beta out for this - also supports UBNT/AirOS now. I've tried it - works!

Seems like some guys missed that RAT is for public download - don't have to ask anyone for it...

Posted: **Wed Jan 14, 2009 11:11 pm**

lol,

How about a WWW/FTP server, and allowing people to DL it?
That way we do not have to publish our email addresses over the internet.

Software sounds good though, would like to get a copy too.

Thanks

Posted: **Sat Jan 24, 2009 10:19 pm**

LOL on you then - if you scroll up that's exactly what you find - a WEB URL...

Posted: **Mon Mar 02, 2009 5:43 pm**

me to please

adp_ucalp@yahoo.com.ar

Posted: **Tue Mar 10, 2009 3:12 am**

may i have the software too...

leo_cakep@yahoo.com

Posted: **Mon Apr 06, 2009 1:55 am**

may i have the software?
chadyagh@hotmail.com
thanks in advance

Posted: **Mon Apr 06, 2009 9:47 am**

can the OP please share a link to this famous app, because all these people's email addresses will be gathered by spambots

Posted: **Tue Apr 07, 2009 4:46 pm**

Yes please

can the OP please share a link to this famous app, because all these people's email addresses will be gathered by spambots

Posted: **Thu Apr 09, 2009 9:32 am**

http://www.witelcom.com/index.php/support/helpntools

RAT

New RAT1.6 : Radio Alignment Tool

Posted: **Tue May 05, 2009 12:16 am**

hi chris, can i have the application pls
chadyagh@hotmail.com

Posted: **Thu Jul 23, 2009 7:21 pm**

Christian

Do you think I could have a copy of this app
m259wf AT YAHOO DOT COM

MFG

Posted: **Thu Jul 23, 2009 10:34 pm**

can the mikrotik team maybe lock this subject

MikroTik

CPE-Antenna alignment via customer / Application available?

CPE-Antenna alignment via customer / Application available?

Program

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?

Re: CPE-Antenna alignment via customer / Application available?